Yamaha RX-V557 owner manual Troubleshooting, General

Page 70

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center.

■General

Problem

Cause

Remedy

Refer to

page

 

 

 

 

 

 

 

This unit fails to turn

The power cord is not connected or the

Connect the power cord firmly.

—

on when STANDBY/

plug is not completely inserted.

 

 

ON (or SYSTEM

The impedance setting is incorrect.

Set the impedance to match your speakers.

56

POWER) is pressed,

or enters the standby

The protection circuitry has been

Make sure all speaker wire connections on this unit

11-13

mode soon after the

power has been

activated.

and on all speakers are secure and that the wire for

 

 

each connection does not touch anything other than

 

turned on.

 

 

 

its respective connection.

 

 

 

 

 

 

 

 

 

This unit has been exposed to a strong

Set this unit in the standby mode, disconnect the

—

 

external electric shock (such as lightning

power cord, plug it back in after 30 seconds, then use

 

 

or strong static electricity).

it normally.

 

 

 

 

 

No sound

Incorrect input or output cable

Connect the cables properly. If the problem persists,

14-20

 

connections.

the cables may be defective.

 

 

The input mode is set to DTS or

Select AUTO.

32

 

ANALOG.

 

 

 

No appropriate input source has been

Select an appropriate input source with INPUT,

25

 

selected.

MULTI CH INPUT (or MULTI CH IN on the remote

 

 

 

control) or the input selector buttons.

 

 

Speaker connections are not secure.

Secure the connections.

12

 

The front speakers to be used have not

Select the front speakers with SPEAKERS A and/or

25

 

been selected properly.

B.

 

 

 

 

 

 

The volume is turned down.

Turn up the volume.

—

 

The sound is muted.

Press MUTE or any operation button of this unit to

26

 

 

resume audio output, then adjust the volume.

 

 

The input mode is set to ANALOG while

Set the input mode to AUTO or DTS.

32

 

playing a source encoded with a DTS

 

 

 

signal.

 

 

 

Signals this unit cannot reproduce are

Play a source whose signals can be reproduced by this

—

 

being received from a source component,

unit.

 

 

such as a CD-ROM.

 

 

 

 

 

 

No picture

The output and input for the picture are

Turn on the video conversion function.

53

 

connected to different types of video

 

 

 

jacks.

 

 

68

Page 69 Page 71
Image 70
Page 69 Page 71
Contents RX-V557 For U.K. customers Special Instructions for U.K. ModelContents Sound field features FeaturesBuilt-in 6-channel power amplifier Other featuresGetting Started Supplied accessoriesInstalling batteries in the remote control Please check that you received all of the following partsControls and Functions Front panelInput Mode VolumePRESET/TUNING Edit Speakers A/BRemote control Using the remote control Front panel display Input channel indicators/speaker indicators 96/24 indicatorLFE indicator Zone 2 indicatorRear panel AC OutletsSpeaker Setup Speaker placementOhms before using see Tighten the knob to secure the wireSpeaker connections Subwoofer jack Front terminalsConnect surround speakers 6, 7 to these terminals Surround Back terminalsBefore connecting components ConnectionsConnecting video components Connections for DVD playbackConnecting to the Multi CH Input jacks Connections for other video components Video AUX jacks on the front panelConnecting audio components Connections for audio componentsClamp it with Pliers Connecting the FM and AM antennasInsert the cable Wire into the slot Snap the cover into placeAC Outlets Switched Connecting the power supply cordConnecting the AC power cord Memory back-upPress STANDBY/ON to turn off the power Speaker impedance settingTurning on the power Rotate Program to move through the menu and select SP IMPBasic Setup Using the Basic Setup menuPress j / i to select the number of speakers you connected Press d to display SET/CANCELPress d to display the Speakers parameter Press Enter to confirm your selectionTo balance the speaker levels Perform the following steps after seeBasic operations Adjust the volume to the desired output levelPlayback Select the input sourceSelect a sound field program if desired To listen with headphonesTo adjust the tone Silent CinemaPlaying video sources Background Selecting sound field programsSelecting Multi CH Input Front panel operationAuto Auto Remote control operationEnjoying multi-channel software Decoders select with jWhen you select the SUR. Enhanced or Movie Theater program Press Select on the remote control to select the decoderWhen you select the SUR. Standard program Enjoying 2-channel software in surroundListening to high fidelity stereo sound Direct Stereo This adjusts the level of compressionNight listening modes Downmixing to 2 channels Listening to unprocessed input signalsVirtual Cinema DSP Rotate Input to select the input source Selecting input modesDisplaying information about the input Source FM/AM Tuning Automatic and manual tuningAutomatically presetting FM stations Presetting stationsManual tuning Hold down the button to continue searchingPress and hold Memory MAN’L/AUTO FM for more than 3 seconds Manually presetting stationsAutomatic preset tuning options Tune into a stationShows the displayed station has been stored as C3 Selecting preset stationsRepeat steps 1 to 5 to store other stations See Selecting preset stations Exchanging preset stationsSelect preset station E1 Press and hold PRESET/TUNING Edit for more than 3 secondsReceiving Radio Data System stations Changing the Radio Data System mode Do not press FREQ/TEXT until a Radio Data System indicatorPTY Seek function Selected program type appears in the front panel displayTo cancel this function EON functionSpecial considerations when recording DTS software RecordingSound Field Program Descriptions For movie/video sourcesSUR. Standard For music sources Hall in ViennaAdvanced Operations Using the sleep timerSetting the sleep timer Canceling the sleep timer Amount of timePress Enter when you have completed your adjustment Manually adjusting speaker levelsPress j / i to adjust the speaker output level Control range is from +10 dB to -10 dBSET Menu Using SET Menu Front speakers Front Speaker settings Aspeaker SETSubwoofer phase Swfr Phase Center speaker CenterUnit Unit Speaker level BSP LevelSpeaker distance CSP Distance Speaker distancesMuting type Mute TYP Audio settings Gaudio SETAudio delay A. Delay Tone bypass TC.BYPASSDisplay settings Adisplay SET Dimmer Dimmer Video conversion V. ConvSpeaker B setting SP B Parameter initialization CPARAM. INIAdvanced Setup menu is displayed in the front panel display Advanced Setup MenuPress STANDBY/ON to confirm your selection Speaker impedance SP IMP Advanced Setup menu itemsFactory presets Preset Remote RemoteControlling this unit Remote Control FeaturesControl area Controlling other componentsPress Code SET using a ballpoint pen or similar object Setting remote control codesRemote Control Code Default Settings Transmit indicator on the remote control flashes twiceControlling other components VCREnter the code number 9991 or 9992 see the table below Switching library codesClearing set up remote control codes Enter the code numberZone System configuration and connections exampleZone 2 connections Remote controlling Zone StandbyFor DVDs encoded in DTS To turn on all units the main unit and Zone 2 unitSpecial considerations for DTS software For CDs encoded in DTSWhat is a sound field Changing parameter settings Editing Sound Field ParametersResetting parameters to the factory Presets Use PARAM. INI seeDSP Level DSP level INIT.DLY Initial delaySound Field Parameter Descriptions For 2ch Stereo Direct DirectCT Width Center width Dimension DimensionFor 6ch Stereo For DTS Neo6 Music Image Center imageTroubleshooting GeneralTroubleshooting Digital Output Remote control TunerRotate Program to move through the menu and select Preset Resetting the Factory PresetsAdvanced Setup menu appears in the front panel display Press Straight Effect to select the desired settingGlossary Audio formatsCinema DSP Sound field programsAudio information ITU-RComposite video signal Video signal informationComponent video signal Video signalSpecifications APPENDIX-i APPENDIX-ii APPENDIX-iii APPENDIX-iv APPENDIX-v All rights reserved
Top Page Image Contents