Yamaha RX-V557 owner manual Recording, Special considerations when recording DTS software

Page 44

RECORDING

Recording adjustments and other operations are performed from the recording components. Refer to the operating instructions for those components.

12

1

2

1Turn on the power of this unit and all connected components.

2Select the source component you want to record from.

INPUT

CD

MD/CD-R

TUNER

SLEEP

 

DVD

DTV/CBL

V-AUX

MULTI CH IN

 

or

 

 

 

 

VCR

 

 

AMP

Front panel

 

Remote control

 

3Start playback (or select a broadcast station) on the source component.

4Start recording on the recording component.

y

Do a test recording before you start an actual recording.

Notes

•When this unit is set in the standby mode, you cannot record between other components connected to this unit.

•The setting of TONE CONTROL, VOLUME, “SP LEVEL” (page 51) and the sound field programs does not affect recorded material.

•A source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.

•S-video and composite video signals pass independently through this unit’s video circuits. Therefore, when recording or dubbing video signals, if your video source component is connected to provide only an S-video (or only a composite video) signal, you can record only an S-video (or only a composite video) signal to your VCR.

•Digital signals input to the DIGITAL INPUT jacks are not output to the analog AUDIO OUT (L/R) jacks for recording. Likewise, analog signals input to the AUDIO IN (L/R) jacks are not output to the DIGITAL OUTPUT jack. Therefore, if your source component is connnected to provide only digital (or analog) signals, you can only record digital (or analog) signals.

•A given input source is not output on the same REC OUT channel. (For example, the signal input from VCR IN is not output on VCR OUT.)

•Check the copyright laws in your country to record from records, CDs, radio, etc. Recording of copyrighted material may infringe copyright laws.

If you playback a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals.

■Special considerations when recording

DTS software

The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being recorded. Therefore, if you want to use this unit to record sources that have DTS signals recorded on them, the following considerations and adjustments need to be made.

For DVDs and CDs encoded with DTS, when your player is compatible with the DTS format, follow its operating instructions to make a setting so that the analog signal will be output from the player.

42

Page 43 Page 45
Image 44
Page 43 Page 45
Contents RX-V557 For U.K. customers Special Instructions for U.K. ModelContents Features Built-in 6-channel power amplifierSound field features Other featuresSupplied accessories Installing batteries in the remote controlGetting Started Please check that you received all of the following partsControls and Functions Front panelVolume PRESET/TUNING EditInput Mode Speakers A/BRemote control Using the remote control Front panel display 96/24 indicator LFE indicatorInput channel indicators/speaker indicators Zone 2 indicatorRear panel AC OutletsSpeaker Setup Speaker placementSpeaker connections Tighten the knob to secure the wireOhms before using see Front terminals Connect surround speakers 6, 7 to these terminalsSubwoofer jack Surround Back terminalsBefore connecting components ConnectionsConnecting video components Connections for DVD playbackConnecting to the Multi CH Input jacks Connections for other video components Video AUX jacks on the front panelConnecting audio components Connections for audio componentsConnecting the FM and AM antennas Insert the cable Wire into the slotClamp it with Pliers Snap the cover into placeConnecting the power supply cord Connecting the AC power cordAC Outlets Switched Memory back-upSpeaker impedance setting Turning on the powerPress STANDBY/ON to turn off the power Rotate Program to move through the menu and select SP IMPBasic Setup Using the Basic Setup menuPress d to display SET/CANCEL Press d to display the Speakers parameterPress j / i to select the number of speakers you connected Press Enter to confirm your selectionTo balance the speaker levels Perform the following steps after seeAdjust the volume to the desired output level PlaybackBasic operations Select the input sourceTo listen with headphones To adjust the toneSelect a sound field program if desired Silent CinemaSelecting sound field programs Selecting Multi CH InputPlaying video sources Background Front panel operationRemote control operation Enjoying multi-channel softwareAuto Auto Decoders select with jPress Select on the remote control to select the decoder When you select the SUR. Standard programWhen you select the SUR. Enhanced or Movie Theater program Enjoying 2-channel software in surroundNight listening modes This adjusts the level of compressionListening to high fidelity stereo sound Direct Stereo Virtual Cinema DSP Listening to unprocessed input signalsDownmixing to 2 channels Displaying information about the input Source Selecting input modesRotate Input to select the input source FM/AM Tuning Automatic and manual tuningPresetting stations Manual tuningAutomatically presetting FM stations Hold down the button to continue searchingManually presetting stations Automatic preset tuning optionsPress and hold Memory MAN’L/AUTO FM for more than 3 seconds Tune into a stationRepeat steps 1 to 5 to store other stations Selecting preset stationsShows the displayed station has been stored as C3 Exchanging preset stations Select preset station E1See Selecting preset stations Press and hold PRESET/TUNING Edit for more than 3 secondsReceiving Radio Data System stations Changing the Radio Data System mode Do not press FREQ/TEXT until a Radio Data System indicatorPTY Seek function Selected program type appears in the front panel displayTo cancel this function EON functionSpecial considerations when recording DTS software RecordingSound Field Program Descriptions For movie/video sourcesSUR. Standard For music sources Hall in ViennaUsing the sleep timer Setting the sleep timer Canceling the sleep timerAdvanced Operations Amount of timeManually adjusting speaker levels Press j / i to adjust the speaker output levelPress Enter when you have completed your adjustment Control range is from +10 dB to -10 dBSET Menu Using SET Menu Speaker settings Aspeaker SET Subwoofer phase Swfr PhaseFront speakers Front Center speaker CenterSpeaker level BSP Level Speaker distance CSP DistanceUnit Unit Speaker distancesAudio settings Gaudio SET Audio delay A. DelayMuting type Mute TYP Tone bypass TC.BYPASSDisplay settings Adisplay SET Dimmer Dimmer Video conversion V. ConvSpeaker B setting SP B Parameter initialization CPARAM. INIPress STANDBY/ON to confirm your selection Advanced Setup MenuAdvanced Setup menu is displayed in the front panel display Advanced Setup menu items Factory presets PresetSpeaker impedance SP IMP Remote RemoteRemote Control Features Control areaControlling this unit Controlling other componentsSetting remote control codes Remote Control Code Default SettingsPress Code SET using a ballpoint pen or similar object Transmit indicator on the remote control flashes twiceControlling other components VCRSwitching library codes Clearing set up remote control codesEnter the code number 9991 or 9992 see the table below Enter the code numberZone 2 connections System configuration and connections exampleZone Remote controlling Zone StandbyTo turn on all units the main unit and Zone 2 unit Special considerations for DTS softwareFor DVDs encoded in DTS For CDs encoded in DTSWhat is a sound field Changing parameter settings Editing Sound Field ParametersResetting parameters to the factory Presets Use PARAM. INI seeINIT.DLY Initial delay Sound Field Parameter DescriptionsDSP Level DSP level For 2ch Stereo Direct DirectDimension Dimension For 6ch StereoCT Width Center width For DTS Neo6 Music Image Center imageTroubleshooting GeneralTroubleshooting Digital Output Remote control TunerResetting the Factory Presets Advanced Setup menu appears in the front panel displayRotate Program to move through the menu and select Preset Press Straight Effect to select the desired settingGlossary Audio formatsSound field programs Audio informationCinema DSP ITU-RVideo signal information Component video signalComposite video signal Video signalSpecifications APPENDIX-i APPENDIX-ii APPENDIX-iii APPENDIX-iv APPENDIX-v All rights reserved
Top Page Image Contents