Yamaha DSP-AX757SE Connecting to an external amplifier, Front PRE OUT jacks, Center PRE OUT jack

Page 22

CONNECTIONS

■Connecting to an external amplifier

If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the PRE OUT jacks as follows.

Notes

•When audio pin plugs are connected to the PRE OUT jacks for output to an external amplifier, do not make connections to the corresponding SPEAKERS terminals. Set the volume of the amplifier connected to this unit to the maximum.

•The signals output through the FRONT PRE OUT and CENTER PRE OUT jacks are affected by the TONE CONTROL settings.

•If SPEAKERS A is turned off and SP B is set to ZONE B (see page 65), signals will only be output from the FRONT PRE OUT jacks.

1	2 3	4
	PRE OUT
	CENTER	SINGLE
	SUB	SURROUND
FRONT	SURROUND WOOFER	BACK

5

1FRONT PRE OUT jacks

Front channel line output jacks.

2SURROUND PRE OUT jacks

Surround channel line output jacks.

3CENTER PRE OUT jack

Center channel line output jack.

4SURROUND BACK PRE OUT jacks

Surround back or presence channel line output jacks.

5SUBWOOFER PRE OUT jack

Connect a subwoofer with built-in amplifier, such as the YAMAHA Active Servo Processing Subwoofer System, to this jack.

Notes

•Each PRE OUT jack outputs the same channel signals as the corresponding speaker terminals.

•Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level using the remote control (see “Manually adjusting speaker levels” on page 53).

•Some signals may not be output from the SUBWOOFER PRE OUT jack depending on the SPEAKER SET (see page 57) and LFE/BASS OUT (see page 58) settings.

20

Image 22

Contents DSP-AX757SE AV Amplifier For U.K. customers Special Instructions for U.K. ModelContents Sound field features FeaturesBuilt-in 7-channel power amplifier Other featuresGetting Started Supplied accessoriesInstalling batteries in the remote control Slide the cover back until it snaps into placeControls and Functions Front panelStraight Effect Input ModeSpeakers A/B FM/AMRemote control Using the remote control Front panel display LFE indicator Sleep indicator96/24 indicator Input channel indicatorsRear panel AC OutletsSpeaker Setup Speaker placement10 mm Speaker connectionsRed positive + Black negative Right Left Front speakers a Subwoofer System Presence speakersRight Left CenterSurround terminals Front terminalsCenter terminals Subwoofer jackBefore connecting components ConnectionsConnections for DVD playback Connecting video componentsVideo Monitor For 6-channel input Connecting to the Multi CH Input jacks External decoder Use these jacks to connect any video source, such as a Connections for other video componentsVideo AUX jacks on the front panel DVD recorder Or VCRConnecting a turntable Connecting audio componentsConnections for audio components Surround PRE OUT jacks Connecting to an external amplifierFront PRE OUT jacks Center PRE OUT jackIndoor FM antenna IncludedAM loop antenna included Ground GND terminalAC Outlets Switched Connecting the power supply cordConnecting the AC power cord Memory back-upPress STANDBY/ON to turn off the power Speaker impedance settingTurning on the power Press Straight Effect repeatedly to select 4 ! MINChecks and adjusts the sound level volume of each speaker Auto SetupIntroduction Optimizer microphone setup Optimizer microphone positionAutomenu Starting the setupAutocheck If an error screen appears ErrorResultexit For details about each message, see Press j / i to switch between warning messagesExample screen Troubleshooting for auto setup procedure Before auto setup Errors during auto setup2OVER 24m 1OUT of Phase3LEVEL Error Cause RemedyBasic operations Adjust the volume to the desired output levelPlayback Select the input sourceSelect a sound field program if desired To adjust the toneTo listen with headphones Silent CinemaFront panel operation Selecting sound field programsSelecting Multi CH Input Playing video sources BackgroundAuto Auto Remote control operationEnjoying multi-channel software Decoders select with jWhen you select the SUR. Enhanced or Movie Theater program Press Select on the remote control to select the decoderWhen you select the SUR. Standard program Enjoying 2-channel software in surroundThis adjusts the level of compression Indicator around the front panel button lights upTo cancel, press Pure Direct again Listening to high fidelity stereo soundPress Straight to select Straight Listening to unprocessed input signalsDownmixing to 2 channels Virtual Cinema DSPDisplaying information about the input Source Press Input Mode to select an input modeSelecting input modes Press StraightRate FlgPress PRESET/TUNING l / h once to begin automatic tuning FM/AM Tuning RX-V757 onlyAutomatic and manual tuning Press FM/AM to select the reception bandAutomatically presetting FM stations Presetting stationsManual tuning Hold down the button toPress and hold Memory MAN’L/AUTO FM for more than 3 seconds Manually presetting stationsAutomatic preset tuning options Tune into a stationShows the displayed station has been stored as C3 Selecting preset stationsPreset number Repeat steps 1 to 5 to store other stationsSee Selecting preset stations Exchanging preset stationsSelect preset station E1 Press and hold PRESET/TUNING Edit for more than 3 secondsReceiving Radio Data System stations PTY Changing the Radio Data System modeFrequency display Control to begin searching all preset Radio Press PRESET/TUNING l / h or PresetCH u / d on the remote control to select Desired program typeTo cancel this function EON functionSpecial considerations when recording DTS software RecordingStereo Sound Field Program DescriptionsFor movie/video sources MusicSound Field Program Descriptions SUR. Standard For music sourcesEntertainment SUR. EnhancedAdvanced Operations Selecting the OSD mode Using the sleep timerP04 Movie Theater Press Enter when you have completed your adjustment Canceling the sleep timerPress j / i to adjust the speaker output level Control range is from +10 dB to -10 dBSET Menu Auto SetupManual Setup Sound MenuSignal Info Option MenuPress Enter to enter Manual Setup Using SET MenuPress u / d to select Manual Setup To exit, press SET Menu when finishedCenter SP Sound Menu 1/2Front SP SUR. L/R SPLFE/BASS OUT SUR. B L/R SPPresence SP Cross OverPriority 02ASUBWOOFER PhaseSubwoofer phase Subwoofer Phase Presence/Surround back channel priorityCSP Distance DequalizerElfe Level Gaudio SETFdynamic Range Optical OUT Input MenuCMPNT-V Input OpticalVolume Trim D Volume Trim Binput ModeInput mode Binput Mode Cinput RenameAdisplay SET Option MenuBmemory Guard Dmulti Zone SET Speaker B setting SP BCPARAM. INI Parameter initialization CPARAM. INIAdvanced Setup menu is displayed in the front panel display Advanced Setup MenuPress STANDBY/ON to confirm your selection Speaker impedance SP IMP Advanced Setup menu itemsFactory presets Preset Remote RemoteControl area Remote Control FeaturesFixing the remote to AMP mode Controlling this unitSetting remote control codes Remote Control Code Default SettingsVOL Digital TV LD player CD player Controlling other componentsDVD player TunerLearn is displayed Programming codes from other remote controlsPress Learn using a ballpoint pen or similar object To 10 cmChanging source names in the display window Press RE-NAME using aPress RE-NAME again to exit from the renaming mode Object Press u / d to select and enter a characterPress Clear to exit from the clearing mode Press Clear by using a ballpoint pen or similar objectPress u / d to select the clear mode Clearing function setsClearing individual functions Clearing a learned functionZone 2 connections System configuration and connections exampleZone 2 RX-V757 only This unitTo enable Zone 2 mode on the remote Control Remote controlling ZoneUsing this unit’s internal amplifier Remote control will be able to operate this unit and ZoneSpecial considerations for DTS software Press Select k/n to exit from the Zone 2 modeTurning this unit to either on or standby For DVDs encoded in DTSWhat is a sound field Changing parameter settings Editing Sound Field ParametersPress u / d to select Press j / i to change Parameter valueDSP Level DSP level INIT. DLY/P. INIT. DLY Initial delaySound Field Parameter Descriptions Room SIZE/P. Room Size Room sizeLiveness Liveness INIT. DLY Surround initial delaySB INI. DLY Surround back initial delay Room Size Surround room sizeREV.TIME Reverberation time REV.DELAY Reverberation delayREV. Level Reverberation level For 2ch Stereo Direct Direct Dimension DimensionDIALG.LIFT Dialog lift For 7ch StereoControl range 0 to Initial setting For DTS Neo6 Music Image Center imageTroubleshooting GeneralOnly the speaker on Problem Cause Remedy Refer to Sound suddenlyGoes off One side can beVolume level is Problem Cause Remedy Refer to Dolby Digital or DTSOr DTS indicator on Record Volume levelTuner With the exception of U.K. model Remote control Resetting the Factory Presets Glossary Audio formatsCinema DSP Sound field programsAudio information ITU-RComposite video signal Video signal informationComponent video signal Video signalSpecifications