Yamaha DSP-AX757SE owner manual Changing source names in the display window, Press RE-NAME using a

Page 75

Notes

•“NG” appears in the display window if programming was unsuccessful. In this case, start over from step 4.

•This remote control can learn approximately 120 functions. However depending on the signals learned, “FULL” may appear in the display before you program 120 functions. In this case, clear unnecessary programmed functions to make room for further learning.

6Repeat steps 4 and 5 to program additional functions.

7Press LEARN again to exit from the learning mode.

LEARN

REMOTE CONTROL FEATURES

Changing source names in the display window

You can change the name that appears in the display window on the remote control if you want to use a different name to the one that is set as the factory preset. This is useful when you have set the input selector to control a different component.

1Press an input selector button to select the source component you want to rename.

The selected component name appears in the display window.

Notes

•Learning may not be possible in the following cases:

– When the batteries in the remote control for this unit or other components are weak.

– When the distance between the two remote controls is too great or too small.

– When the remote control infrared windows are not facing at the appropriate angle.

– When the remote control is exposed to direct sunlight.

– When the function to be programmed is continuous or uncommon.

•“ERROR” appears in the display window if you press more than one button at the same time.

2Press RE-NAME using a

ballpoint pen or similar

RE-NAME

object.

3Press u / d to select and enter a character.

Pressing d changes the character as follows:

A to Z, a to z, 0 to 9, space, -(hyphen), and /(slash). (Pressing u changes the characters in reverse order.)

PRESET

TV VOL

CH

CH

TV VOL

PRESET

4Press j / i to move the cursor to the next position.

PRESET

TV VOL

CH

CH

TV VOL

PRESET

y

If you want to continue setting up names for other components, press TV MUTE/SELECT and repeat steps 1, 3 and 4.

5Press RE-NAME again to exit from the renaming mode.

RE-NAME

OPERATION	ADVANCED

English

73

Image 75

Contents DSP-AX757SE AV Amplifier Special Instructions for U.K. Model For U.K. customersContents Other features FeaturesBuilt-in 7-channel power amplifier Sound field featuresSlide the cover back until it snaps into place Supplied accessoriesInstalling batteries in the remote control Getting StartedFront panel Controls and FunctionsFM/AM Input ModeSpeakers A/B Straight EffectRemote control Using the remote control Front panel display Input channel indicators Sleep indicator96/24 indicator LFE indicatorAC Outlets Rear panelSpeaker placement Speaker SetupSpeaker connections 10 mmRed positive + Black negative Center Subwoofer System Presence speakersRight Left Right Left Front speakers aSubwoofer jack Front terminalsCenter terminals Surround terminalsConnections Before connecting componentsConnecting video components Connections for DVD playbackVideo Monitor Connecting to the Multi CH Input jacks For 6-channel inputExternal decoder DVD recorder Or VCR Connections for other video componentsVideo AUX jacks on the front panel Use these jacks to connect any video source, such as aConnecting audio components Connecting a turntableConnections for audio components Center PRE OUT jack Connecting to an external amplifierFront PRE OUT jacks Surround PRE OUT jacksGround GND terminal Indoor FM antenna IncludedAM loop antenna includedMemory back-up Connecting the power supply cordConnecting the AC power cord AC Outlets SwitchedPress Straight Effect repeatedly to select 4 ! MIN Speaker impedance settingTurning on the power Press STANDBY/ON to turn off the powerOptimizer microphone position Auto SetupIntroduction Optimizer microphone setup Checks and adjusts the sound level volume of each speakerStarting the setup AutomenuAutocheck Error If an error screen appearsResultexit Press j / i to switch between warning messages For details about each message, seeExample screen Errors during auto setup Troubleshooting for auto setup procedure Before auto setupCause Remedy 1OUT of Phase3LEVEL Error 2OVER 24mSelect the input source Adjust the volume to the desired output levelPlayback Basic operationsSilent Cinema To adjust the toneTo listen with headphones Select a sound field program if desiredPlaying video sources Background Selecting sound field programsSelecting Multi CH Input Front panel operationDecoders select with j Remote control operationEnjoying multi-channel software Auto AutoEnjoying 2-channel software in surround Press Select on the remote control to select the decoderWhen you select the SUR. Standard program When you select the SUR. Enhanced or Movie Theater programListening to high fidelity stereo sound Indicator around the front panel button lights upTo cancel, press Pure Direct again This adjusts the level of compressionVirtual Cinema DSP Listening to unprocessed input signalsDownmixing to 2 channels Press Straight to select StraightPress Straight Press Input Mode to select an input modeSelecting input modes Displaying information about the input SourceFlg RatePress FM/AM to select the reception band FM/AM Tuning RX-V757 onlyAutomatic and manual tuning Press PRESET/TUNING l / h once to begin automatic tuningHold down the button to Presetting stationsManual tuning Automatically presetting FM stationsTune into a station Manually presetting stationsAutomatic preset tuning options Press and hold Memory MAN’L/AUTO FM for more than 3 secondsRepeat steps 1 to 5 to store other stations Selecting preset stationsPreset number Shows the displayed station has been stored as C3Press and hold PRESET/TUNING Edit for more than 3 seconds Exchanging preset stationsSelect preset station E1 See Selecting preset stationsReceiving Radio Data System stations Changing the Radio Data System mode PTYFrequency display Desired program type Press PRESET/TUNING l / h or PresetCH u / d on the remote control to select Control to begin searching all preset RadioEON function To cancel this functionRecording Special considerations when recording DTS softwareMusic Sound Field Program DescriptionsFor movie/video sources StereoSound Field Program Descriptions SUR. Enhanced For music sourcesEntertainment SUR. StandardSelecting the OSD mode Using the sleep timer Advanced OperationsP04 Movie Theater Control range is from +10 dB to -10 dB Canceling the sleep timerPress j / i to adjust the speaker output level Press Enter when you have completed your adjustmentSound Menu Auto SetupManual Setup SET MenuOption Menu Signal InfoTo exit, press SET Menu when finished Using SET MenuPress u / d to select Manual Setup Press Enter to enter Manual SetupSUR. L/R SP Sound Menu 1/2Front SP Center SPCross Over SUR. B L/R SPPresence SP LFE/BASS OUTPresence/Surround back channel priority 02ASUBWOOFER PhaseSubwoofer phase Subwoofer Phase PriorityDequalizer CSP DistanceGaudio SET Elfe LevelFdynamic Range Optical Input MenuCMPNT-V Input Optical OUTCinput Rename Binput ModeInput mode Binput Mode Volume Trim D Volume TrimOption Menu Adisplay SETBmemory Guard Parameter initialization CPARAM. INI Speaker B setting SP BCPARAM. INI Dmulti Zone SETAdvanced Setup Menu Advanced Setup menu is displayed in the front panel displayPress STANDBY/ON to confirm your selection Remote Remote Advanced Setup menu itemsFactory presets Preset Speaker impedance SP IMPControlling this unit Remote Control FeaturesFixing the remote to AMP mode Control areaRemote Control Code Default Settings Setting remote control codes VOL Tuner Controlling other componentsDVD player Digital TV LD player CD playerTo 10 cm Programming codes from other remote controlsPress Learn using a ballpoint pen or similar object Learn is displayedObject Press u / d to select and enter a character Press RE-NAME using aPress RE-NAME again to exit from the renaming mode Changing source names in the display windowClearing function sets Press Clear by using a ballpoint pen or similar objectPress u / d to select the clear mode Press Clear to exit from the clearing modeClearing a learned function Clearing individual functionsThis unit System configuration and connections exampleZone 2 RX-V757 only Zone 2 connectionsRemote control will be able to operate this unit and Zone Remote controlling ZoneUsing this unit’s internal amplifier To enable Zone 2 mode on the remote ControlFor DVDs encoded in DTS Press Select k/n to exit from the Zone 2 modeTurning this unit to either on or standby Special considerations for DTS softwareEditing Sound Field Parameters What is a sound field Changing parameter settingsPress j / i to change Parameter value Press u / d to selectRoom SIZE/P. Room Size Room size INIT. DLY/P. INIT. DLY Initial delaySound Field Parameter Descriptions DSP Level DSP levelRoom Size Surround room size INIT. DLY Surround initial delaySB INI. DLY Surround back initial delay Liveness LivenessREV.DELAY Reverberation delay REV.TIME Reverberation timeREV. Level Reverberation level For 7ch Stereo Dimension DimensionDIALG.LIFT Dialog lift For 2ch Stereo Direct DirectFor DTS Neo6 Music Image Center image Control range 0 to Initial settingGeneral TroubleshootingOne side can be Problem Cause Remedy Refer to Sound suddenlyGoes off Only the speaker onRecord Volume level Problem Cause Remedy Refer to Dolby Digital or DTSOr DTS indicator on Volume level isTuner With the exception of U.K. model Remote control Resetting the Factory Presets Audio formats GlossaryITU-R Sound field programsAudio information Cinema DSPVideo signal Video signal informationComponent video signal Composite video signalSpecifications