Yamaha DSP-AX757SE owner manual Option Menu, Adisplay SET, Bmemory Guard

Page 66

SET MENU

3 OPTION MENU

Use to adjust the optional system parameters.

3 OPTION MENU

.

B)MEMORY

C)PARAM.

D)MULTI ZONE

p

p

■Display settings A)DISPLAY SET

A)DISPLAY SET

.;;;;;;;;;0

;;;ON

;;;;;;0

;;;AUTO

;;;;;ON

p

p

Dimmer DIMMER

Use to adjust the brightness of the front panel display. Choices: –4 to 0

Video conversion VIDEO CONV.

Use this feature to turn on/off conversion of composite (VIDEO) signals to both S-video and component signals. This allows you to output converted video signals from the S VIDEO or COMPONENT VIDEO jacks when no S-video or component signals are input. This feature also converts S-video signals to component signals when no component signals are input.

Choices: ON, OFF

•Select OFF not to convert any signals (except S-video signals to composite signals).

•Select ON to convert composite signals to S-video and component signals, and to convert S-video signals to component signals.

•Regardless of the setting, S-video signals are always converted to composite signals.

Notes

•Converted video signals are only output to the MONITOR OUT jacks. When recording you must make the same type of video connections (i.e., S-video) between each component.

•When converting composite video or S-video signals from a VCR to component video signals, the picture quality may suffer depending on your VCR.

OSD shift OSD SHIFT

Use to adjust the vertical position of the OSD. Choices: +5 (downward) to –5 (upward)

•Press + to lower the position of the OSD.

•Press – to raise the position of the OSD.

Gray back GRAY BACK

Selecting AUTO for the on-screen display setting displays a gray background when there’s no video signal input. Nothing is displayed if OFF is selected.

Choices: AUTO, OFF

Notes

•When only the component video signals are input, the OSD is not displayed if GRAY BACK is set to OFF. To display the OSD with component video signal input, set GRAY BACK to AUTO while the OSD mode (see page 52) is set to “Full display”.

•When video signals are not being input, set GRAY BACK to AUTO to display the OSD.

Component OSD CMPNT OSD

Use this feature to turn on/off OSD output to the COMPONENT VIDEO MONITOR OUT jacks when using the SET MENU.

Choices: ON, OFF

•Select ON to output the OSD signals from COMPONENT VIDEO MONITOR OUT jacks.

•Select OFF if you do not want to output the OSD signals from COMPONENT VIDEO MONITOR OUT jacks.

Note

SET MENU functions even when OFF is selected.

■Memory guard B)MEMORY GUARD

Use this feature to prevent accidental changes to DSP program parameter values and other system settings. Choices: OFF, ON

B)MEMORY GUARD

)OFF

Select ON to protect:

•DSP program parameters

•All SET MENU items

•All speaker levels

•The on-screen display (OSD) mode

Note

When MEMORY GUARD is set to ON, you cannot select any other SET MENU items.

64

Page 65 Page 67
Image 66
Page 65 Page 67
Contents DSP-AX757SE AV Amplifier For U.K. customers Special Instructions for U.K. ModelContents Sound field features FeaturesBuilt-in 7-channel power amplifier Other featuresGetting Started Supplied accessoriesInstalling batteries in the remote control Slide the cover back until it snaps into placeControls and Functions Front panelStraight Effect Input ModeSpeakers A/B FM/AMRemote control Using the remote control Front panel display LFE indicator Sleep indicator96/24 indicator Input channel indicatorsRear panel AC OutletsSpeaker Setup Speaker placementSpeaker connections 10 mmRed positive + Black negative Right Left Front speakers a Subwoofer System Presence speakersRight Left CenterSurround terminals Front terminalsCenter terminals Subwoofer jackBefore connecting components ConnectionsConnecting video components Connections for DVD playbackVideo Monitor Connecting to the Multi CH Input jacks For 6-channel inputExternal decoder Use these jacks to connect any video source, such as a Connections for other video componentsVideo AUX jacks on the front panel DVD recorder Or VCRConnecting audio components Connecting a turntableConnections for audio components Surround PRE OUT jacks Connecting to an external amplifierFront PRE OUT jacks Center PRE OUT jackIndoor FM antenna IncludedAM loop antenna included Ground GND terminalAC Outlets Switched Connecting the power supply cordConnecting the AC power cord Memory back-upPress STANDBY/ON to turn off the power Speaker impedance settingTurning on the power Press Straight Effect repeatedly to select 4 ! MINChecks and adjusts the sound level volume of each speaker Auto SetupIntroduction Optimizer microphone setup Optimizer microphone positionStarting the setup AutomenuAutocheck Error If an error screen appearsResultexit Press j / i to switch between warning messages For details about each message, seeExample screen Troubleshooting for auto setup procedure Before auto setup Errors during auto setup2OVER 24m 1OUT of Phase3LEVEL Error Cause RemedyBasic operations Adjust the volume to the desired output levelPlayback Select the input sourceSelect a sound field program if desired To adjust the toneTo listen with headphones Silent CinemaFront panel operation Selecting sound field programsSelecting Multi CH Input Playing video sources BackgroundAuto Auto Remote control operationEnjoying multi-channel software Decoders select with jWhen you select the SUR. Enhanced or Movie Theater program Press Select on the remote control to select the decoderWhen you select the SUR. Standard program Enjoying 2-channel software in surroundThis adjusts the level of compression Indicator around the front panel button lights upTo cancel, press Pure Direct again Listening to high fidelity stereo soundPress Straight to select Straight Listening to unprocessed input signalsDownmixing to 2 channels Virtual Cinema DSPDisplaying information about the input Source Press Input Mode to select an input modeSelecting input modes Press StraightRate FlgPress PRESET/TUNING l / h once to begin automatic tuning FM/AM Tuning RX-V757 onlyAutomatic and manual tuning Press FM/AM to select the reception bandAutomatically presetting FM stations Presetting stationsManual tuning Hold down the button toPress and hold Memory MAN’L/AUTO FM for more than 3 seconds Manually presetting stationsAutomatic preset tuning options Tune into a stationShows the displayed station has been stored as C3 Selecting preset stationsPreset number Repeat steps 1 to 5 to store other stationsSee Selecting preset stations Exchanging preset stationsSelect preset station E1 Press and hold PRESET/TUNING Edit for more than 3 secondsReceiving Radio Data System stations Changing the Radio Data System mode PTYFrequency display Control to begin searching all preset Radio Press PRESET/TUNING l / h or PresetCH u / d on the remote control to select Desired program typeTo cancel this function EON functionSpecial considerations when recording DTS software RecordingStereo Sound Field Program DescriptionsFor movie/video sources MusicSound Field Program Descriptions SUR. Standard For music sourcesEntertainment SUR. EnhancedSelecting the OSD mode Using the sleep timer Advanced OperationsP04 Movie Theater Press Enter when you have completed your adjustment Canceling the sleep timerPress j / i to adjust the speaker output level Control range is from +10 dB to -10 dBSET Menu Auto SetupManual Setup Sound MenuSignal Info Option MenuPress Enter to enter Manual Setup Using SET MenuPress u / d to select Manual Setup To exit, press SET Menu when finishedCenter SP Sound Menu 1/2Front SP SUR. L/R SPLFE/BASS OUT SUR. B L/R SPPresence SP Cross OverPriority 02ASUBWOOFER PhaseSubwoofer phase Subwoofer Phase Presence/Surround back channel priorityCSP Distance Dequalizer Gaudio SET Elfe Level Fdynamic Range Optical OUT Input MenuCMPNT-V Input OpticalVolume Trim D Volume Trim Binput ModeInput mode Binput Mode Cinput RenameOption Menu Adisplay SETBmemory Guard Dmulti Zone SET Speaker B setting SP BCPARAM. INI Parameter initialization CPARAM. INIAdvanced Setup Menu Advanced Setup menu is displayed in the front panel displayPress STANDBY/ON to confirm your selection Speaker impedance SP IMP Advanced Setup menu itemsFactory presets Preset Remote RemoteControl area Remote Control FeaturesFixing the remote to AMP mode Controlling this unitSetting remote control codes Remote Control Code Default SettingsVOL Digital TV LD player CD player Controlling other componentsDVD player TunerLearn is displayed Programming codes from other remote controlsPress Learn using a ballpoint pen or similar object To 10 cmChanging source names in the display window Press RE-NAME using aPress RE-NAME again to exit from the renaming mode Object Press u / d to select and enter a characterPress Clear to exit from the clearing mode Press Clear by using a ballpoint pen or similar objectPress u / d to select the clear mode Clearing function setsClearing individual functions Clearing a learned functionZone 2 connections System configuration and connections exampleZone 2 RX-V757 only This unitTo enable Zone 2 mode on the remote Control Remote controlling ZoneUsing this unit’s internal amplifier Remote control will be able to operate this unit and ZoneSpecial considerations for DTS software Press Select k/n to exit from the Zone 2 modeTurning this unit to either on or standby For DVDs encoded in DTSWhat is a sound field Changing parameter settings Editing Sound Field ParametersPress u / d to select Press j / i to change Parameter valueDSP Level DSP level INIT. DLY/P. INIT. DLY Initial delaySound Field Parameter Descriptions Room SIZE/P. Room Size Room sizeLiveness Liveness INIT. DLY Surround initial delaySB INI. DLY Surround back initial delay Room Size Surround room sizeREV.DELAY Reverberation delay REV.TIME Reverberation timeREV. Level Reverberation level For 2ch Stereo Direct Direct Dimension DimensionDIALG.LIFT Dialog lift For 7ch StereoControl range 0 to Initial setting For DTS Neo6 Music Image Center imageTroubleshooting GeneralOnly the speaker on Problem Cause Remedy Refer to Sound suddenlyGoes off One side can beVolume level is Problem Cause Remedy Refer to Dolby Digital or DTSOr DTS indicator on Record Volume levelTuner With the exception of U.K. model Remote control Resetting the Factory Presets Glossary Audio formatsCinema DSP Sound field programsAudio information ITU-RComposite video signal Video signal informationComponent video signal Video signalSpecifications
Top Page Image Contents