Q-See QSZ515D Setting of DIP Switches, Setting Baud Rate, SW2, Bit, Setting Address Code

Problem		Possible reason		Solution
No movement a		1.Check the connection of		1.Check the power
ge at power-on		C power input		connection, make sure			th
		2.Turn off power and ch		ket is well		connected
		he transformer		2.Make sure the power ou
				working
Power-on	sh	1. DIP switch setting is in		1.	Refer to setup		in
mage,		2.RS485 interface is not c		ons, re-set the DIP switch
but the	co	ted or is not	connecte	2.Check RS485 interface,
r doesnot work		ctly		sure the wires are well co
		3.There is a problem with		ed	and in the proper sl
		S485 line		3.Refer to the Appendix:
Blurred Image		Ball case is dirty		Clean the ball case

2.2. Setting of DIP Switches

The internal black case has 8 DIP switches. 8,7,6,5,4,3,2,1 are for Addres s setting, while 10,9 are for Communication Baud Rate.

In the following table, tag “1” for DIP switch “ON”; tag “0” for DIP switch “off”.

a)Setting Baud Rate

	Switch #		SW2			Switch #		SW2
Baud Rate		（		）	Baud Ra		（		）
	BIT	10	9			BIT	10	9
2400bps		0	1		1200bps		1	1
4800bps		1	0		9600bps		0	0

b) b) Setting Address Code

In a system, decoder includes intelligent speed dome camera and common de coder. No repeating address codes exist. As you see in the table, “1” for “O

N”, “0” for	“OFF”
Address		Address Switch							(8	Address	Address Switch								8
Code		1	2	3	4	5	6	7	8	Code	1	2	3	4	5	6	7	8	（
1		1 0 0 0 0 0 0 0								33	1 0 0 0 0 1 0 0
2		0 1 0 0 0 0 0 0								34	0 1 0 0 0 1 0 0
3		1 1 0 0 0 0 0 0								35	1 1 0 0 0 1 0 0

4		0 0 1 0 0 0 0 0	36	0 0 1 0 0 1 0 0
5		1 0 1 0 0 0 0 0	37	1 0 1 0 0 1 0 0
6		0 1 1 0 0 0 0 0	38	0 1 1 0 0 1 0 0
7		1 1 1 0 0 0 0 0	39	1 1 1 0 0 1 0 0
8		0 0 0 1 0 0 0 0	40	0 0 0 1 0 1 0 0
9		1 0 0 1 0 0 0 0	41	1 0 0 1 0 1 0 0
10		0 1 0 1 0 0 0 0	42	0 1 0 1 0 1 0 0
11		1 1 0 1 0 0 0 0	43	1 1 0 1 0 1 0 0
12		0 0 1 1 0 0 0 0	44	0 0 1 1 0 1 0 0
13		1 0 1 1 0 0 0 0	45	1 0 1 1 0 1 0 0
14		0 1 1 1 0 0 0 0	46	0 1 1 1 0 1 0 0
15		1 1 1 1 0 0 0 0	47	1 1 1 1 0 1 0 0
16		0 0 0 0 1 0 0 0	48	0 0 0 0 1 1 0 0
17		1 0 0 0 1 0 0 0	49	1 0 0 0 1 1 0 0
18		0 1 0 0 1 0 0 0	50	0 1 0 0 1 1 0 0
19		1 1 0 0 1 0 0 0	51	1 1 0 0 1 1 0 0
20		0 0 1 0 1 0 0 0	52	0 0 1 0 1 1 0 0
21		1 0 1 0 1 0 0 0	53	1 0 1 0 1 1 0 0
22		0 1 1 0 1 0 0 0	54	0 1 1 0 1 1 0 0
23		1 1 1 0 1 0 0 0	55	1 1 1 0 1 1 0 0
24		0 0 0 1 1 0 0 0	56	0 0 0 1 1 1 0 0
25		1 0 0 1 1 0 0 0	57	1 0 0 1 1 1 0 0
26		0 1 0 1 1 0 0 0	58	0 1 0 1 1 1 0 0
27		1 1 0 1 1 0 0 0	59	1 1 0 1 1 1 0 0
28		0 0 1 1 1 0 0 0	60	0 0 1 1 1 1 0 0
29		1 0 1 1 1 0 0 0	61	1 0 1 1 1 1 0 0
30		0 1 1 1 1 0 0 0	62	0 1 1 1 1 1 0 0
31		1 1 1 1 1 0 0 0
32	：		··	········
	0 0 0 0 0 1 0 0		255	1 1 1 1 1 1 1 1
Part 5	PELCO-D Protocol

Data Form 1 beginning position, 10 pieces for data, 1 ending position, invalid checking point