Plasmon LF6600 user manual Configuration Mode

Page 62

CONFIGURATION MODE

Configuration mode is used to view and set drive operating parameters. The parameters that can be configured and displayed are summarized in the following (the corresponding DOC display is shown in parentheses).

Viewing the configuration ("View Config")

View the current operating parameters ("View Current")

View the firmware revisions of the drive ("View FW Revs")

View the hardware revisions of the drive ("View HW S/Ns")

View the hardware part numbers of the drive ("View HW P/Ns")

Setting the configuration of the operating parameters ("Set Config")

Set all parameters to the default value ("Set Defaults")

Set device SCSI identification number 0 through 7 ("SCSI ID:")

Enable or disable parity checking ("Parity:")

Set language option to English, French or German ("Language:")

Enable or disable write protect option ("Wrt Prot:")

Enable or disable media AutoLoad option ("AutoLoad:")

Enable or disable load switch option ("Load SW:")

Enable or disable read ahead ("Rd Ahead:")

Enable or disable Controller Detected Error blink option ("CDE Curs:")

Enable or disable Busy option ("Busy")

Enable or disable Mode Select Read Ahead ("ModSel RA")

Enable of disable Media Management Spin Up ("MM SpinUp")

Viewing diagnostic results or performing diagnostic operations ("Diagnostics")

Park the drive in preparation for shipment ("Park Drive")

Display the state of the drive sensors ("Test Sensors")

Clear the drive initialization variables in nonvolatile memory ("Clear NvRAM")

Allow Shuttle Calibration (“Cal Shuttle”)

Display controller detected error information ("View CDEs")

Enable or disable system event logging ("Sys Log:")

Set the extent of internal diagnostic test coverage ("Test Thru:")

View Real Time Performance Monitor ("View RTPM")

Clear RTPM error ("Clear RTPM")

Initialize DPC ("Init DPC")

Set the internal drive serial number ("Set Serial #")

Configuration mode can be entered when the "Ready" message is displayed on the DOC. To enter the Configuration mode:

1)Press both the LOAD/MENU and TEST/SELECT switches simultaneously.

2)Verify that "View Config" is displayed.

PLASMON LASER MAGNETIC STORAGE - LF 6600 User Manual Page 62

Image 62
Contents Optical Disk Drive Page Page Page Agency Compliance and Approval Page Table of Contents Accessories Scope Related PublicationsPage General Description Page Drive Characteristics LF 6600 Tower Configuration Front Panel Rear Panel Dimensions and Weight Shipping WeightTEMPERATURE, Humidity and Altitude TransitAC Power Requirements Shock and VibrationAC Ground AC Power CordPower Supply OUT-OF-RANGE Protection Features Tilt RangeLocation of LF 6600 Warning Labels Page Unpacking the Tower Configuration Unpacking and Repacking InstructionsLF 6600 Tower Packing Caster for the LF 6600 Tower Unpacking the Rack Mount Configuration LF 6600 Rack Mount Packing Inspecting the LF Repacking the LFClosing the Baseplates Repacking the Tower Configuration Repacking the Rack Mount Configuration Page Installation and DE Installation RequirementsTower Installation Rack Mount Installation LF 6600 Side-by-Side Rack Mount Page Mounting the Platform Support Rack Mounting the Slide Assembly to the Platform Support Rack Extending the Slide Platform Assembly Rear Do Not Extend Both Drives Simultaneously Mounting the LF 6600 Chassis to the Extended Platform LF 6600 Rack Mount Slide Detail Standard Rack Mounted LF 6600 in the Retention Lock Position Installing the Lateral Support Angle Blank Panel Installation Scsi BUS Considerations LF 6600-to-Host Cable Connection Connecting Power and Scsi Cables Connecting the Power Cord Connecting Multiple DevicesConnecting a Single Device Connector Verification Rack Mount Configuration DE-INSTALLATION Vertical Tail Page Controls and Indicators Operating InstructionsTEST/SELECT POWER-ON Procedure Operating Mode Modes of OperationOperating Condition DOC Display English French German Configuration Mode Page Main Menu Viewing the Configuration View Config View Configuration MessagesDisplay HW Page Page Scsi ID Rd Ahead Setting the Scsi ID Setting the BUS Parity CheckingSetting the Language Setting the Write Protect OptionSetting the Media Autoload Option Setting the Load Switch OptionSetting the Read Ahead Option Setting the CDE Curs OptionSetting the Busy Option Setting the Modsel RA OptionSetting the MM Spinup Option Clear NvRAM OMA Clear Rtpm Diagnostics Menu Part SET the Internal Drive Serial Number SET Serial # Page DRV SN Test Mode Media Cartridge Handling HUB and Magnet RingPage Setting the Write Protection Switch Affixing Labels Media Insertion and RemovalLF 6600 Media Access Cartridge Insertion Cartridge Removal Manual Cartridge Release Mechanism Opening the BaseplatesRemoving the Bezel Back View of Bezel Retracting the Cartridge Media Loading Operator Maintenance Inspecting and Cleaning FAN and Blower FiltersReplacing Fuses Removing Fuse from AC Power Receptacle Rear View of LF Media Cleaning Media Cleaning Using Cleaning KIT P/NAccessories Length Connector a Connector B NumberPlasmon Product Table below contains optional power cables for each country Page Abmessungen UND Gewicht Appendix aGerman Translations / Übersetzungen INS Deutsche TEMPERATUR, Luftfeuchtigkeit UND SeehöheBedingung Betrieb Ruhe Lagerung Transport Stoss UND Vibration WechselstrombedarfWärmeausstrahlung WechselstromerdungKipptoleranz Grenzwerte FÜR DIE StaubkonzentrationWiederverpacken DES LF VorsichtEinsetzung Erforderis Turmmontage Anschlussüberprüfung ANSCHLUß DES NetzkabelsAbbau DER Gestellmontagenkonfiguration Einstellen DIE Device ID HinweisHandhabung VON Datenträgerkassetten Einstellen DIE Read Option VorsichtVorsicht Auswechseln VON Sicherungen Vorsicht