Plasmon LF6600 user manual SET the Internal Drive Serial Number SET Serial #

Page 81

A

PRESS BOTH SWITCHES SIMULTANEOUSLY TO RETURN TO MAIN MENU

"Set Config"

 

SELECT

Display RTPM

View RTPM

Information

 

 

 

MENU

 

 

 

SELECT

RTPM

Y

Confirm Clear

True

 

 

 

 

 

N

 

SELECT

Clear RTPM

No RTPM Err

 

 

 

 

RTPM Condition is Cleared

MENU

 

 

 

Init DPC

SELECT

Init Done

Reset Drive

Self Test

MENU

Diagnostic Menu (Part 2)

SET THE INTERNAL DRIVE SERIAL NUMBER ("SET SERIAL #")

To enter the serial number submenu, press the TEST/SELECT switch while "Set Serial #" is displayed in the Main menu. The drive will enter the menu allowing the operator to view and change the internal drive serial number.

NOTE

The serial number set in the drive must correspond to the last 5 digits of the drive's actual serial number for accurate internal event logging to occur. The drive's actual serial number is located on the back of the drive enclosure.

To change the drive's 5-digit serial number, follow these steps:

1)Enter the Configuration mode by simultaneously pressing the LOAD/MENU and TEST/ SELECT switches.

2)Press the MENU switch until "Set Serial #" is displayed.

3)Press the SELECT switch to enter the serial number mode. The serial number will be displayed.

97653976 F Page 81

Image 81
Contents Optical Disk Drive Page Page Page Agency Compliance and Approval Page Table of Contents Accessories Related Publications ScopePage General Description Page Drive Characteristics LF 6600 Tower Configuration Front Panel Rear Panel Shipping Weight Dimensions and WeightTransit TEMPERATURE, Humidity and AltitudeShock and Vibration AC Power RequirementsPower Supply OUT-OF-RANGE Protection Features AC Power CordAC Ground Tilt RangeLocation of LF 6600 Warning Labels Page Unpacking and Repacking Instructions Unpacking the Tower ConfigurationLF 6600 Tower Packing Caster for the LF 6600 Tower Unpacking the Rack Mount Configuration LF 6600 Rack Mount Packing Repacking the LF Inspecting the LFClosing the Baseplates Repacking the Tower Configuration Repacking the Rack Mount Configuration Page Installation Requirements Installation and DETower Installation Rack Mount Installation LF 6600 Side-by-Side Rack Mount Page Mounting the Platform Support Rack Mounting the Slide Assembly to the Platform Support Rack Extending the Slide Platform Assembly Rear Do Not Extend Both Drives Simultaneously Mounting the LF 6600 Chassis to the Extended Platform LF 6600 Rack Mount Slide Detail Standard Rack Mounted LF 6600 in the Retention Lock Position Installing the Lateral Support Angle Blank Panel Installation Scsi BUS Considerations LF 6600-to-Host Cable Connection Connecting Power and Scsi Cables Connecting Multiple Devices Connecting the Power CordConnecting a Single Device Connector Verification Rack Mount Configuration DE-INSTALLATION Vertical Tail Page Operating Instructions Controls and IndicatorsTEST/SELECT POWER-ON Procedure Modes of Operation Operating ModeOperating Condition DOC Display English French German Configuration Mode Page Main Menu View Configuration Messages Viewing the Configuration View ConfigDisplay HW Page Page Scsi ID Rd Ahead Setting the BUS Parity Checking Setting the Scsi IDSetting the Write Protect Option Setting the LanguageSetting the Load Switch Option Setting the Media Autoload OptionSetting the CDE Curs Option Setting the Read Ahead OptionSetting the Modsel RA Option Setting the Busy OptionSetting the MM Spinup Option Clear NvRAM OMA Clear Rtpm Diagnostics Menu Part SET the Internal Drive Serial Number SET Serial # Page DRV SN Test Mode HUB and Magnet Ring Media Cartridge HandlingPage Setting the Write Protection Switch Media Insertion and Removal Affixing LabelsLF 6600 Media Access Cartridge Insertion Cartridge Removal Opening the Baseplates Manual Cartridge Release MechanismRemoving the Bezel Back View of Bezel Retracting the Cartridge Media Loading Inspecting and Cleaning FAN and Blower Filters Operator MaintenanceReplacing Fuses Removing Fuse from AC Power Receptacle Rear View of LF Media Cleaning Using Cleaning KIT P/N Media CleaningLength Connector a Connector B Number AccessoriesPlasmon Product Table below contains optional power cables for each country Page German Translations / Übersetzungen INS Deutsche Appendix aAbmessungen UND Gewicht TEMPERATUR, Luftfeuchtigkeit UND SeehöheBedingung Betrieb Ruhe Lagerung Transport Wechselstrombedarf Stoss UND VibrationKipptoleranz WechselstromerdungWärmeausstrahlung Grenzwerte FÜR DIE StaubkonzentrationVorsicht Wiederverpacken DES LFEinsetzung Erforderis Turmmontage ANSCHLUß DES Netzkabels AnschlussüberprüfungEinstellen DIE Device ID Hinweis Abbau DER GestellmontagenkonfigurationEinstellen DIE Read Option Vorsicht Handhabung VON DatenträgerkassettenVorsicht Auswechseln VON Sicherungen Vorsicht