SUPER MICRO Computer 5015A-EHF user manual Checking the Drive Bay Setup, Checking the Drives

Page 24

SUPERSERVER 5015A-EHF User's Manual

2-7 Checking the Drive Bay Setup

Next, you should check to make sure the drives have been properly installed and all essential connections have been made.

Checking the Drives

1.Depending upon your system's configuration, your system may have one or two Serial ATA drives already installed.

2.If you need to install Serial ATA drives, please refer to the appropriate section in Chapter 6.

Providing Power

1.The last thing you must do is to provide input power to the system. Plug the power cord from the power supply unit into a high-quality power strip that of- fers protection from electrical noise and power surges. It is recommended that you use an uninterruptible power supply (UPS).

2.Finish by depressing the power button on the chassis control panel.

2-8

Image 24
Contents Super Manual Revision 1.0b Release Date February 21 About This Manual Manual OrganizationAdvanced Motherboard Setup Advanced Chassis SetupBios Preface Table of Contents Standardized Warning Statements for AC Systems Viii Advanced Chassis Setup Page Chapter Introduction OverviewMotherboard Features Intel Atom D510 + ICH9R Chipset System Block Diagram Server Chassis Features Contacting Supermicro HeadquartersEurope Asia-PacificPage Preparing for Setup Choosing a Setup LocationUnpacking the System Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling into a Telco Rack Rack Mounting InstructionsInstalling the Chassis into a Telco Rack Checking the Motherboard Setup Accessing the Inside of the System FigureAccessing the Inside of the System Checking the Drive Bay Setup Checking the DrivesReset Button PowerControl Panel Buttons Control Panel LEDsOverheat HDDPower Page Chapter Standardized Warning Statements for AC Systems About Standardized Warning Statementsהרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可 されています。Restricted Area Battery Handling Page Redundant Power Supplies Backplane Voltage ירוחאה לנפב חתמ Comply with Local and National Electrical Codesיצראה למשחה יקוח םואית Product Disposalרצומה קוליס Hot Swap Fan Warning當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Power Cable and AC Adapter AC ימאתמו םיילמשח Page Chapter Advanced Motherboard Setup Handling the MotherboardMotherboard Installation UnpackingConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelControl Panel Header Pins I/O PortsInstalling Memory Dimm InstallationOnboard Processor Memory SupportDimm Installation Installing an Expansion Card Adding PCI Expansion CardsNumber Jumper Description Default Setting Motherboard DetailsNumber Connector Description JPCIE1Connector Definitions Main ATX Power Supply ConnectorExternal Power Connector Power ButtonReset Button Power Fail LEDOverheat/Fan Fail Power LED NMI ButtonFan Headers Overheat/Fan Fail LED JOHSata DOM Power Power SMB I2C ConnectorChassis Intrusion Serial PortsSgpio 0/1 Headers ATX PS/2 Keyboard and PS/2 Mouse PortsUniversal Serial Bus USB LAN1/2 Ethernet PortsJumper Settings LAN1/2 Enable/DisableExplanation of Jumpers Cmos ClearWatch Dog Enable/Disable Power Force On Enable/DisableVGA Enable/Disable SMB I2C Bus to PCI SlotsBMC Enable/Disable DCD / P5V SelectSpeaker Jumper Onboard Indicators Sata PortsLAN1/2 LEDs Sata PortsInstalling Software SuperDoctor Onboard Battery SuperDoctor III Interface Display Screen Remote ControlPage Page Control Panel Chassis Front ViewDrive Bay Installation/Removal System FansInstalling a 3.5 Hard Drive Power Supply Replacing the Power Supply FigureInstalling the Power Supply Starting Bios Setup Utility How To Change the Configuration DataIntroduction Main Setup How to Start the Setup UtilitySystem Time/System Date ProcessorSystem Memory Advanced Setup Configurations BOOT FeatureQuick Boot Quiet BootBootup Num-Lock Wait For F1 If ErrorPower Button Function Restore on AC Power LossStandby Power in S5 CPU ConfigurationClock Spread Spectrum Max Cpuid Value LimitAdvanced Chipset Control Northbridge ConfigurationIDE/SATA Configuration IDE Detect Timeout sec LBA/Large ModePIO Mode TypeDMA Mode PCI/PnP Configuration Remote Access Configuration Super IO Device ConfigurationRedirection After Bios Post Sredir Memory Display DelayFlow Control Terminal TypeCPU Overheat Alarm CPU TemperatureSystem Temperature Hardware Health ConfigurationCpufan / Sysfan Speed High Performance Event Timer ACPI ConfigurationFan Speed Control Modes USB Device WakeupSuspend Mode Headless ModeAcpi Version Features Acpi Aware O/SIPMI Configuration Event Log Configuration Security Settings Supervisor PasswordUser Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionBoot Settings Boot Device PriorityHard Disk Drives Retry Boot Devices Exit OptionsRemovable Drives Save Changes and ExitLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes and Exit Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications