SUPER MICRO Computer 5015A-EHF Flow Control, Redirection After Bios Post, Terminal Type

Page 89

Chapter 7: BIOS

Flow Control

This feature allows the user to set the flow control for Console Redirection. The options are None, Hardware, and Software.

Redirection After BIOS POST

Select Disabled to turn off Console Redirection after Power-On Self-Test (POST). Select Always to keep Console Redirection active all the time after POST. (Note: This setting may not be supported by some operating systems.) Select Boot Loader to keep Console Redirection active during POST and Boot Loader. The options are Disabled, Boot Loader, and Always.

Terminal Type

This feature allows the user to select the target terminal type for Console Redi- rection. The options are ANSI, VT100, and VT-UTF8.

VT-UTF8 Combo Key Support

A terminal keyboard definition that provides a way to send commands from a remote console. Available options are Enabled and Disabled.

Sredir Memory Display Delay

This feature defines the length of time in seconds to display memory information. The options are No Delay, Delay 1 Sec, Delay 2 Sec, and Delay 4 Sec.

7-13

Image 89
Contents Super Manual Revision 1.0b Release Date February 21 Manual Organization About This ManualBios Advanced Motherboard SetupAdvanced Chassis Setup Preface Table of Contents Standardized Warning Statements for AC Systems Viii Advanced Chassis Setup Page Overview Chapter IntroductionMotherboard Features Intel Atom D510 + ICH9R Chipset System Block Diagram Server Chassis Features Headquarters Contacting SupermicroEurope Asia-PacificPage Unpacking the System Preparing for SetupChoosing a Setup Location Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureRack Mounting Instructions Installing into a Telco RackInstalling the Chassis into a Telco Rack Accessing the Inside of the System Figure Checking the Motherboard SetupAccessing the Inside of the System Checking the Drives Checking the Drive Bay SetupPower Reset ButtonControl Panel Buttons Control Panel LEDsHDD OverheatPower Page About Standardized Warning Statements Chapter Standardized Warning Statements for AC Systemsהרהזא תורהצה ןונקת Bewaar Deze Instructies 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 Installation InstructionsCircuit Breaker Power Disconnection Warning םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可 されています。 Equipment InstallationRestricted Area Battery Handling Page Redundant Power Supplies Backplane Voltage Comply with Local and National Electrical Codes ירוחאה לנפב חתמProduct Disposal יצראה למשחה יקוח םואיתHot Swap Fan Warning רצומה קוליס當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Power Cable and AC Adapter AC ימאתמו םיילמשח Page Handling the Motherboard Chapter Advanced Motherboard SetupUnpacking Motherboard InstallationConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelI/O Ports Control Panel Header PinsDimm Installation Installing MemoryOnboard Processor Memory SupportDimm Installation Adding PCI Expansion Cards Installing an Expansion CardMotherboard Details Number Jumper Description Default SettingJPCIE1 Number Connector DescriptionMain ATX Power Supply Connector Connector DefinitionsExternal Power Connector Power ButtonOverheat/Fan Fail Reset ButtonPower Fail LED NMI Button Power LEDFan Headers Overheat/Fan Fail LED JOHPower SMB I2C Connector Sata DOM PowerChassis Intrusion Serial PortsATX PS/2 Keyboard and PS/2 Mouse Ports Sgpio 0/1 HeadersUniversal Serial Bus USB LAN1/2 Ethernet PortsLAN1/2 Enable/Disable Jumper SettingsExplanation of Jumpers Cmos ClearPower Force On Enable/Disable Watch Dog Enable/DisableVGA Enable/Disable SMB I2C Bus to PCI SlotsSpeaker Jumper BMC Enable/DisableDCD / P5V Select Sata Ports Onboard IndicatorsLAN1/2 LEDs Sata PortsInstalling Software SuperDoctor SuperDoctor III Interface Display Screen Remote Control Onboard BatteryPage Page Chassis Front View Control PanelSystem Fans Drive Bay Installation/RemovalInstalling a 3.5 Hard Drive Replacing the Power Supply Figure Power SupplyInstalling the Power Supply Introduction Starting Bios Setup UtilityHow To Change the Configuration Data How to Start the Setup Utility Main SetupSystem Memory System Time/System DateProcessor BOOT Feature Advanced Setup ConfigurationsQuick Boot Quiet BootWait For F1 If Error Bootup Num-LockPower Button Function Restore on AC Power LossCPU Configuration Standby Power in S5Clock Spread Spectrum Max Cpuid Value LimitNorthbridge Configuration Advanced Chipset ControlIDE/SATA Configuration LBA/Large Mode IDE Detect Timeout secPIO Mode TypeDMA Mode PCI/PnP Configuration Super IO Device Configuration Remote Access ConfigurationSredir Memory Display Delay Redirection After Bios PostFlow Control Terminal TypeCPU Temperature CPU Overheat AlarmSystem Temperature Hardware Health ConfigurationCpufan / Sysfan Speed ACPI Configuration High Performance Event TimerFan Speed Control Modes USB Device WakeupHeadless Mode Suspend ModeAcpi Version Features Acpi Aware O/SIPMI Configuration Event Log Configuration Supervisor Password Security SettingsUser Password Change Supervisor PasswordBoot Sector Virus Protection Change User PasswordHard Disk Drives Boot SettingsBoot Device Priority Exit Options Retry Boot DevicesRemovable Drives Save Changes and ExitLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes and Exit Discard ChangesRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications