SUPER MICRO Computer 5015A-EHF user manual Connector Deﬁnitions, Main ATX Power Supply Connector

Page 58

SUPERSERVER 5015A-EHF User's Manual

5-9 Connector Deﬁnitions

ATX Power 24-pin Connector

Pin Deﬁnitions

Main ATX Power Supply

Connector

The 24-pin main power connector (JPW1) is used to provide power to the motherboard. This power connec- tor meets the SSI EPS 12V speciﬁca- tion. See the table on the right for pin deﬁnitions.

Pin# Deﬁnition

13+3.3V

14-12V

15COM

16PS_ON

17COM

18COM

19COM

20Res (NC)

21+5V

22+5V

23+5V

24COM

Pin # Deﬁnition

1+3.3V

2+3.3V

3COM

4+5V

5COM

6+5V

7COM

8PWR_OK

95VSB

10+12V

11+12V

12+3.3V

Required Connection

External Power Connector

In addition to the 24-pin main power connector, the 4-pin External Power connector at J8 is used to provide power to external devices such as hard disks & CD-ROM drives. This power connector supports 12V and 5V devices.

Power Button

The Power Button connection is located on pins 1 and 2 of JF1. Momentarily contacting both pins will power on/off the system. To turn off the power when set to suspend mode, press the button for at least 4 seconds. Refer to the table on the right for pin deﬁnitions.

4-Pin External Power

Connector

Pin Deﬁnitions

Pin Deﬁnition

1+12V

2Ground 1

3Ground 2

4+5V

Optional Connection

Power Button

Pin Deﬁnitions (JF1)

Pin# Deﬁnition

1Power Signal

2Ground

5-10

Image 58

Contents Super Manual Revision 1.0b Release Date February 21 About This Manual Manual OrganizationAdvanced Chassis Setup Advanced Motherboard SetupBios Preface Table of Contents Standardized Warning Statements for AC Systems Viii Advanced Chassis Setup Page Chapter Introduction OverviewMotherboard Features Intel Atom D510 + ICH9R Chipset System Block Diagram Server Chassis Features Europe Contacting SupermicroHeadquarters Asia-PaciﬁcPage Choosing a Setup Location Preparing for SetupUnpacking the System Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling into a Telco Rack Rack Mounting InstructionsInstalling the Chassis into a Telco Rack Checking the Motherboard Setup Accessing the Inside of the System FigureAccessing the Inside of the System Checking the Drive Bay Setup Checking the DrivesControl Panel Buttons Reset ButtonPower Control Panel LEDsOverheat HDDPower Page Chapter Standardized Warning Statements for AC Systems About Standardized Warning Statementsהרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可されています。Restricted Area Battery Handling Page Redundant Power Supplies Backplane Voltage ירוחאה לנפב חתמ Comply with Local and National Electrical Codesיצראה למשחה יקוח םואית Product Disposalרצומה קוליס Hot Swap Fan Warning當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他物品太靠近風扇。 Power Cable and AC Adapter AC ימאתמו םיילמשח Page Chapter Advanced Motherboard Setup Handling the MotherboardMotherboard Installation UnpackingConnecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins I/O PortsOnboard Processor Installing MemoryDimm Installation Memory SupportDimm Installation Installing an Expansion Card Adding PCI Expansion CardsNumber Jumper Description Default Setting Motherboard DetailsNumber Connector Description JPCIE1External Power Connector Connector DeﬁnitionsMain ATX Power Supply Connector Power ButtonPower Fail LED Reset ButtonOverheat/Fan Fail Fan Headers Power LEDNMI Button Overheat/Fan Fail LED JOHChassis Intrusion Sata DOM PowerPower SMB I2C Connector Serial PortsUniversal Serial Bus USB Sgpio 0/1 HeadersATX PS/2 Keyboard and PS/2 Mouse Ports LAN1/2 Ethernet PortsExplanation of Jumpers Jumper SettingsLAN1/2 Enable/Disable Cmos ClearVGA Enable/Disable Watch Dog Enable/DisablePower Force On Enable/Disable SMB I2C Bus to PCI SlotsDCD / P5V Select BMC Enable/DisableSpeaker Jumper LAN1/2 LEDs Onboard IndicatorsSata Ports Sata PortsInstalling Software SuperDoctor Onboard Battery SuperDoctor III Interface Display Screen Remote ControlPage Page Control Panel Chassis Front ViewDrive Bay Installation/Removal System FansInstalling a 3.5 Hard Drive Power Supply Replacing the Power Supply FigureInstalling the Power Supply How To Change the Conﬁguration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup UtilityProcessor System Time/System DateSystem Memory Quick Boot Advanced Setup ConﬁgurationsBOOT Feature Quiet BootPower Button Function Bootup Num-LockWait For F1 If Error Restore on AC Power LossClock Spread Spectrum Standby Power in S5CPU Conﬁguration Max Cpuid Value LimitAdvanced Chipset Control Northbridge ConﬁgurationIDE/SATA Conﬁguration PIO Mode IDE Detect Timeout secLBA/Large Mode TypeDMA Mode PCI/PnP Conﬁguration Remote Access Conﬁguration Super IO Device ConﬁgurationFlow Control Redirection After Bios PostSredir Memory Display Delay Terminal TypeSystem Temperature CPU Overheat AlarmCPU Temperature Hardware Health ConﬁgurationCpufan / Sysfan Speed Fan Speed Control Modes High Performance Event TimerACPI Conﬁguration USB Device WakeupAcpi Version Features Suspend ModeHeadless Mode Acpi Aware O/SIPMI Conﬁguration Event Log Conﬁguration User Password Security SettingsSupervisor Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionBoot Device Priority Boot SettingsHard Disk Drives Removable Drives Retry Boot DevicesExit Options Save Changes and ExitDiscard Changes and Exit Load Optimal DefaultsLoad Fail-Safe Defaults Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Speciﬁcations System Input Requirements Appendix B System Speciﬁcations