SUPER MICRO Computer 5015A-EHF user manual Power Disconnection Warning

Page 34

SUPERSERVER 5015A-EHF User's Manual

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다.

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A.

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord removed from the power supply module(s) before accessing the chassis interior to install or remove system components.

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス するには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り 外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu entfernen.

4-6

Image 34
Contents Super Manual Revision 1.0b Release Date February 21 About This Manual Manual OrganizationAdvanced Chassis Setup Advanced Motherboard SetupBios Preface Table of Contents Standardized Warning Statements for AC Systems Viii Advanced Chassis Setup Page Chapter Introduction OverviewMotherboard Features Intel Atom D510 + ICH9R Chipset System Block Diagram Server Chassis Features Europe Contacting SupermicroHeadquarters Asia-PacificPage Choosing a Setup Location Preparing for SetupUnpacking the System Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling into a Telco Rack Rack Mounting InstructionsInstalling the Chassis into a Telco Rack Checking the Motherboard Setup Accessing the Inside of the System FigureAccessing the Inside of the System Checking the Drive Bay Setup Checking the DrivesControl Panel Buttons Reset ButtonPower Control Panel LEDsOverheat HDDPower Page Chapter Standardized Warning Statements for AC Systems About Standardized Warning Statementsהרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可 されています。Restricted Area Battery Handling Page Redundant Power Supplies Backplane Voltage ירוחאה לנפב חתמ Comply with Local and National Electrical Codesיצראה למשחה יקוח םואית Product Disposalרצומה קוליס Hot Swap Fan Warning當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Power Cable and AC Adapter AC ימאתמו םיילמשח Page Chapter Advanced Motherboard Setup Handling the MotherboardMotherboard Installation UnpackingConnecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins I/O PortsOnboard Processor Installing MemoryDimm Installation Memory SupportDimm Installation Installing an Expansion Card Adding PCI Expansion CardsNumber Jumper Description Default Setting Motherboard DetailsNumber Connector Description JPCIE1External Power Connector Connector DefinitionsMain ATX Power Supply Connector Power ButtonPower Fail LED Reset ButtonOverheat/Fan Fail Fan Headers Power LEDNMI Button Overheat/Fan Fail LED JOHChassis Intrusion Sata DOM PowerPower SMB I2C Connector Serial PortsUniversal Serial Bus USB Sgpio 0/1 HeadersATX PS/2 Keyboard and PS/2 Mouse Ports LAN1/2 Ethernet PortsExplanation of Jumpers Jumper SettingsLAN1/2 Enable/Disable Cmos ClearVGA Enable/Disable Watch Dog Enable/DisablePower Force On Enable/Disable SMB I2C Bus to PCI SlotsDCD / P5V Select BMC Enable/DisableSpeaker Jumper LAN1/2 LEDs Onboard IndicatorsSata Ports Sata PortsInstalling Software SuperDoctor Onboard Battery SuperDoctor III Interface Display Screen Remote ControlPage Page Control Panel Chassis Front ViewDrive Bay Installation/Removal System FansInstalling a 3.5 Hard Drive Power Supply Replacing the Power Supply FigureInstalling the Power Supply How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup UtilityProcessor System Time/System DateSystem Memory Quick Boot Advanced Setup ConfigurationsBOOT Feature Quiet BootPower Button Function Bootup Num-LockWait For F1 If Error Restore on AC Power LossClock Spread Spectrum Standby Power in S5CPU Configuration Max Cpuid Value LimitAdvanced Chipset Control Northbridge ConfigurationIDE/SATA Configuration PIO Mode IDE Detect Timeout secLBA/Large Mode TypeDMA Mode PCI/PnP Configuration Remote Access Configuration Super IO Device ConfigurationFlow Control Redirection After Bios PostSredir Memory Display Delay Terminal TypeSystem Temperature CPU Overheat AlarmCPU Temperature Hardware Health ConfigurationCpufan / Sysfan Speed Fan Speed Control Modes High Performance Event TimerACPI Configuration USB Device WakeupAcpi Version Features Suspend ModeHeadless Mode Acpi Aware O/SIPMI Configuration Event Log Configuration User Password Security SettingsSupervisor Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionBoot Device Priority Boot SettingsHard Disk Drives Removable Drives Retry Boot DevicesExit Options Save Changes and ExitDiscard Changes and Exit Load Optimal DefaultsLoad Fail-Safe Defaults Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications