Sony CCD-FX310 operation manual Set the Power switch on the camcorder as follows

Page 19

By using the Remote Commander, you can be tn the p_cturewith your friends and family. or conveniently control the playback of your tape from a distance.

1

2

Insert two size AA (R6) batteries with the + and - ends properly positioned.

Set the [] REMOTE COMMANDER

switch on the battery mounting surface of the camcorder,

If the battery is attached, remove tt.

Reattach the battery after setting the

REMOTE COMMANDER ON/OFF switch.

3 Set the POWER switch on the camcorder as follows:

--When camerarecording, 1) press the small green button on the POWER switch and slide it to CAMERA, 2) set the STANDBY switch up.

m When playing back, slide the POWER switch to PLAYER.

4 Aim the Commander at the remote

press the appropriate button on sensor on the camcorder and

the Commander.

	•,--_	- Remote sensor
	_-.f2	m (6.6 ft)
	(6.6.!	m/16 4
2 m		\_.---....,4.
2 m	_ --'"_-

__5

°J3

0o

(Approximate maximum distance and angles for remote control)

Note on the Remote Commander

•Keep the remote sensor away from strong lightsources such as direct sunhght or illummat_on Remote control with the Commander may not function properly ander such circumstances.

•The command mode of the Commander _sVTR2 Avoid using the Sony VCRs with the same command mode at the same time

Getting familiar with some buttons

HOLD switch

When you slide the switch in the direction of the arrow, all the buttons will become inoperable to prevent any misoperation should you

accidentally press the buttons.

I1_ SLOW and DATA SCREEN buttons

You can use the functions of these buttons only with the Commander.

'R._-,,- _ HOLD

--1_ SLOW

. r

DATA SCREEN

Battery life In normal operation, batteries last up to six months. If the camcorder does not

operate properly, the batteries might be exhausted. Replace both batteries with new ones

To avoid damage from possible battery leakage

Remove the batteries when you w_ll not use the Commander for a long time.

When you connect the receiver of a remote control kit

When you connect the receiver of a remote control kit (not supplied) to the REMOTE tt control connector, be sure to set the I1 REMOTE COMMANDER switch on the battery

mounting surface of the camcorder to OFF.	19
Basic Camera Operation

Image 19

Contents CCD FX310 Regulations Information for the customers in the U.S.AGetting Started Basic Camera Operation How to recordAdvanced Camera Operation Connecting Before You BeginWelcome to Video You also need to set the Beep switch Wireless RemoteUse the battery completely before recharging 110 Battery life and remaining capacityCassette compartment marked Push Adjustment ring Press the small Green button on PowerWhat is a sports finder? When storing your camcorderChanging the lithium battery Correcting the date and time settings Adjust the blinking digits of minute by pressing Date +Press Time Next to set the second to Birthday Indicator appears Viewfinder How to store birth datePower switch and slide the Power To Camera CAMpV Set the Standby switch upNow itsready for recording If you missed the correct number with Date +You can see through the viewfinder Press START/STOP red button onceChecking the time remaining on the tape When you have finished recordingTAPEiBATT Check To zoom PhtANT Video inputs, seeInsert a tape. See When you have finished playback Eject the tape, seePress Play Getting familiar with some buttons Set the Power switch on the camcorder as followsMake sure you use up Battery before recharging Battery life is shorter in cold climatesHow to use the switch on the battery pack Why the battery pack heats up?Recommended temperatures during charging Place Power source Accessory to be used To remove the do pack Removeit thesame wayas youdo with the batterypack. SeepagePress START/STOP Press AGE/EVENT to select the indicator you want to recordTo stop recording the age To cancel the stored birth dateTo change the display while recording Hold the viewfinderwith yourthumb to prevent Press the side of Editsearch momentarilySide for the playback picture in reverse To pause recording At the desired point, release Editsearch Press START/STOPIf the tape reaches near the end during recording 111 Press Counter ResetRemote Accessory shoeAfter shooting Press Back LightSports mode To choose best programmed AE modeSet the Program AE switch to To the desired setting When fading-out Press Fader while recording FADERindicatorstarts blinkingTo cancel the fade-in/out function AC-V35/V35A AC-V35/V35A a VcRITo locate the desired scene picture search To view the still picture playback pauseCounter shows Press when the playback has finished, as usualPress 11or IH At the point you later want to locateAUO,ON , DEO Pause How to connectTo stop editing Using of the Edit switchIf you use the Data Screen function If moisture condenses on the lens How to prevent moisture condensationIf moisture condenses Inside the unit If moisture condenses on the surface of the tapeTo clean the viewfinder Take a good posture for shooting To reattach the eyecupNtsc system countries Plan aheadLighting Difference In Color SystemOn care On operationDo not let sand get into the camcorder Do not let the camcorder get wetStandby switch Tape transport buttons Play playback Additional Information Additional Informatton II F£ FJit=TlvJL fl3TJm Power zoom button LiD- Slow slow playback buttonCorrective actions Atiach the battery Power does not turnCause SymptomBeeps General Wireless Ra madSystem Input and output O.etbrInformation Center O,P