IBM 8086, 8088 Additional safety information, Lithium battery notice, Modem safety information

Page 11

Additional safety information

DANGER

Electrical current from power, telephone, and communication cables is hazardous.

To avoid a shock hazard:

vDo not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

vConnect all power cords to a properly wired and grounded electrical outlet.

vConnect to properly wired outlets any equipment that will be attached to this product.

vWhen possible, use one hand only to connect or disconnect signal cables.

vNever turn on any equipment when there is evidence of fire, water, or structural damage.

vDisconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

vConnect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

To connect:

To disconnect:

1.

Turn everything OFF.

1.

Turn everything OFF.

2.

First, attach all cables to devices.

2.

First, remove power cords from outlet.

3.

Attach signal cables to connectors.

3.

Remove signal cables from connectors.

4.

Attach power cords to outlet.

4.

Remove all cables from devices.

5.

Turn device ON.

 

 

 

 

 

 

Lithium battery notice

CAUTION:

Danger of explosion if battery is incorrectly replaced.

When replacing the battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

Do not:

vThrow or immerse into water

vHeat to more than 100°C (212°F)

vRepair or disassemble

Dispose of the battery as required by local ordinances or regulations.

Modem safety information

To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as:

vNever install telephone wiring during a lightning storm.

vNever install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Important safety information

ix

Page 10 Page 12
Image 11
Page 10 Page 12
Contents User Guide Types 8086, 8087 Types 8089 Page User Guide Types 8086, 8087 Types 8089 Page Contents Iv User Guide Conditions that require immediate action Important safety information Power cords and power adapters General safety guidelines Service Batteries Extension cords and related devicesPlugs and outlets Heat and product ventilation CD and DVD drive safetyTo connect To disconnect Additional safety informationLithium battery notice Modem safety informationLaser compliance statement Power supply statementInformation resources OverviewXii User Guide Features Installing optionsVideo subsystem Operating systems preinstalled varies by model type Specifications Available options Supported operating positionsHandling static-sensitive devices Locating the connectors on the front of your computer Installing external optionsLocating the connectors on the rear of your computer Obtaining device drivers Connector DescriptionOpening the cover Identifying parts on the system board Locating componentsInstalling memory Installing options What to do next Installing a PCI adapterWhat to do next Removing and replacing an optical drive Installing internal drivesRemoving and replacing a hard disk drive User Guide Connecting a parallel ATA hard disk drive Integrated cable lock Password protection Security featuresChanging the battery Erasing a lost or forgotten password clearing Cmos Closing the cover and connecting the cables User Guide Exiting from the IBM Setup Utility program Using the IBM Setup Utility programStarting the IBM Setup Utility program Viewing and changing settingsUsing Security Profile by Device User passwordAdministrator password Setting, changing, and deleting a passwordChanging the startup sequence Using IDE Drives SetupSelecting a startup device Selecting a temporary startup deviceUser Guide System programs Updating flashing Bios from a disketteUpdating flashing Bios from your operating system Appendix A. Updating system programsRecovering from a POST/BIOS update failure Appendix A. Updating system programs User Guide Cleaning a mouse with a ball Appendix B. Cleaning the mouseCleaning an optical mouse User Guide Basic AT commands Appendix C. Manual modem commandsInternal speaker on until carrier detected Low speaker volumeSet Pulse dial as default Set Tone Dial as defaultExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 2 commands Fax Class 1 commandsVoice commands Appendix C. Manual modem commands User Guide Tier 2 CRUs Appendix D. Customer replaceable unit CRU parts listTier 1 CRUs User Guide Appendix E. Notices Trademarks Television output noticeIndex Security integrated cable lock Page Part Number 19R2375
Top Page Image Contents