Minolta 5600HS (D) appendix Using The Built-In Flash, Set the camera to wireless flash

Page 24

WIRELESS/REMOTE FLASH MODE

[1]-1 Using The Built-In Flash

1. Attach the 5600HS (D) to the camera and switch the flash and camera power supplies on.

2.Set the camera to wireless flash.

•The method used for the setting varies with the camera. See the cam-

era manual for details.

• When the camera is set to wireless the 5600HS (D) is also set to wire- less automatically, and WL is dis- played on the data panel.

3.Remove the 5600HS (D) from the camera and raise the built- in flash.

4.Set up the camera and the 5600HS (D).

•See page 43 for details.

5.Check that the built-in flash

and 5600HS (D) are fully charged.

• is lit in the viewfinder when the built-in flash is fully charged.

• The AF illuminator on the front blinks, and on the rear is lit, when the 5600 HS (D) is fully charged.

6.Use test flash to check the 5600HS (D) flash.

•The method used for test flash differs with the camera used (eg. press the AE lock button, or spot AE lock button). See the camera manual for details.

•If the test flash doesn’t fire, change the position of the camera, flash, and subject, or point the wireless/remote control-signal receiver towards the camera.

7.Check again that the built-in flash and the 5600HS (D) are fully charged, and press the shutter-release button to take the photo.

[1]-2 Ratio-Flash Control Using The Built-In Flash

The built-in flash and 5600HS (D) may be controlled to a flash

intensity of 1 and 2 respectively. See photo on page 40.

The method used differs with the camera. See the camera manual for details.

•Set shutter speed to 1/60 of a second or less (low shutter speed). Wireless high-speed sync photography cannot be used.

•Ratio-flash control cannot be used with the Maxxum QTsi, 300si, and Dynax 303si, 300si.

[1]-3 Setting Wireless/Remote Flash By Flash Only

If you keep using the same camera and the flash combination with- out changing the wireless channel, it will not be necessary to attach the flash to the camera the next time.

•Camera’s setting : See the camera manual for detail.

•5600HS (D)’s setting : Follow the step 1 to 5 in page 49.

•This procedure is not available with the Maxxum QTsi, 400si, 300si and the Dynax 500siSuper, 500si, 303si, 300si.

WIRELESS FLASH

46

47

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Program Flash Maxxum Flash Applications AppendixFor Proper and Safe USE Contents Cameras and Flash Units CamerasFlash Units Flash Unit Diagram Control Panel Names of PartsNames of Parts Data PanelInstalling Batteries Chamber Close the battery-chamber doorChecking Batteries Auto Power ON/OFF and Film Attaching and RemovalMode Flash the Basics Press the shutter-release butTon partway down and check That the subject is within Flash rangeMode Flash the Basics Exposure ModesSet the aperture and focus the subject Set the shutter speed, and focus the subjectExposure Modes Set the aperture and shutter speed, and focus the sub- jectZoom Flash Coverage Auto ZoomZoom Zoom Flash Coverage Manual ZoomBuilt-In Wide Angle Adapter 17mm zoom angle Pull out the adapterHold The setting prevents mis-operation TEST-FLASH/MODELING FlashFlash once at the set light level Level 1/1~1/32 Bounce Flash FlashFlash may be set to the following angles Adjusting Bounce Angle Bounce FlashData Panel Illuminator AF IlluminatorPress the data panel illuminator Illuminates the data panel at low-light levelsMode and Select Buttons MODE/SELECT ButtonPress the + or button to select the power level to be set Manual Flash MHIGH-SPEED Sync HSS PlayPanel HSSWIRELESS/REMOTE Flash Mode Types Of Wireless/Remote FlashUsing the built-in flash p Using two flash units pWIRELESS/REMOTE Flash Mode Using the Wireless Remote Flash Controller pWireless Flash Range Following two modes are avail- ableWIRELESS/REMOTE Flash Mode Using The Built-In Flash Set the camera to wireless flashSetting Wireless/Remote Flash By Flash Only Check that the built-in flash 5600HS D are fully chargedUsing Two Flash Units Setting Up The ControllerSetting Up The Off-Camera Flash Switch the 5600HS D onCheck that both flash units are fully charged Use test flash to check the off-camera flashPress the select button Taking PhotosUsing Wireless Remote Flash Controller Ratio-Flash Control Using Two Or More Flash UnitsUsing 5600HS D, 5400HS, 5400xi only Refer to the Wireless Remote Flash Controller manualPress the select button Using with 3600HS D or Set up the 5600HS D with the wireless ratio off-camera flashConnecting Camera and Flash by Cable Equalizing The Power Level Of All Flash UnitsConnecting by Cable All the flash units in a and B group can be usedSetting Power Level Level Power LevelPower level for the flash can be adjusted Multiple Flash Multi Press the select button to blinkPress the + or button to Select the number of flashes Multiple Flash Multi Press the select button to blink Level on the data panelPress the select button Set the shutter speed and aperture Maximum Number Of Continuous FlashesReset to Default Settings Custom FunctionPress the select button for Seconds Press the select button toPress the mode button Wireless channel settingTime to auto power off Time to auto power off when using wirelessUsing xi Series Single Lens Reflex Cameras Maxxum/Dynax 9xi, 7xi, 5xi, 3xi, SPxiUsing Early AF Series Single Lens Reflex Cameras Using APS Single Lens Reflex CamerasUsing Minolta Digital Cameras USE in Combination with Other ProductsAccessories AccessoriesTemperature MaintenanceDuring Photography BatteriesPerformance PerformanceMemo 9222-8841-11 P-B00X
Top Page Image Contents