AGFA DC-1030I manual Disclaimer, Extending battery life

Page 2

Thank you for purchasing this DC-1030i digital camera. Please read these operating instructions carefully in order to use the product correctly. Keep the instructions in a safe place after reading so that you can refer to them later.

Disclaimer

We assume no responsibility over and above the provisions of the Product Liability Law for damages suffered by the user or third parties as a result of inappropriate handling of the product or its accessories, or by their operational failure and by their use. We reserve the right to make changes to this product and its accessories without prior notice.

Warning! Never try to open the camera or to take it apart. This will invalidate all guarantee claims.

Using your batteries

For best performance and prolonged battery life, we recommend the use of AA lithium or rechargeable NiMH batteries.

Extending battery life

The following functions use up a great deal of battery power and should therefore only be used occasionally:

•Excessive use of flash

•Editing images on the camera display

•Using the camera display as a view finder

The battery life can be affected by soiling. Please clean the contacts with a clean and dry cloth before putting the batteries in the camera.

Battery performance drops at temperatures below 5 °C (41 °F). If you use the camera at low temperatures you should have replacement batteries to hand and ensure they do not get too cold. Please note: you should not dispose of cold and seemingly flat batteries because these batteries may work again at room temperature

i

Image 2

Contents Page Extending battery life DisclaimerPrecautions Iii „ FCC Compliance and AdvisoryContents Appendix Using This Menu Getting StartedScope of delivery Attaching the Wrist StrapParts of the Camera Page Inserting the Batteries Low Battery IndicatorAbout Battery Type Tips Inserting the Memory CardInsert the card About Camera MemorySelect a language Setting the Display Language / Date & TimeSetting the Display Language Press the Menu button to close the menuSet date and time Setting the Date & TimeApply the setting Using the LCD Monitor REC modePlayback mode DpofChanging the LCD Status „ REC mode„ Playback mode Power Saving Function Turning the Power On and OffPress the Power button n again to turn the power off Basic OperationSelecting the REC mode Changing the ModeSwitching between REC mode and Playback mode Set the camera to the REC mode Launch the mode paletteLaunch the ASM mode Selecting the ASM modeSet the camera to the REC mode Exit the ASM modeREC menu Using the MenusChange the setting Select an itemREC menu list Movie Setup menuOpen the Setup menu Off Press the Menu n button to close the menu Setup menu listBeep SecPAL ResetNtsc Computer / PrinterHalf press the shutter button to focus the image Basic RecordingRecording Still Images Take a pictureUsing the Q mode Quality Values Setting Image Size and QualityResolution Values Using the Zoom Function Using the Flash Using the Macro Double Using the Self-timer & Burst10 sec BurstUsing the Shutter Priority Using the Aperture PriorityTurn the power on, and set the camera to Using the Manual Exposure Setting the Movie Size Recording Movie ClipsPlaying Back Audio Clips Recording Audio ClipsPress the shutter button again to end recording Press the SET button to start recording for 30 seconds Recording a Voice MemoOpen the Playback menu Playing Back a Voice MemoOther Recording Functions Setting the MeteringSetting the White Balance Setting the AEB Setting the ISOSetting the Exposure Setting the HighlightSetting Date Stamp Setting the SharpnessSetting the Photo Effect Playing Back Images Turn the power on, and set the camera to the Playback modePlayback Press the four-way control or nTrim the image Magnifying & Trimming Still ImagesMagnify the image Save the imagePlaying a Slide Show Change the slide show settingsViewing in Thumbnail Playing the slide showDeleting a Single File Playback mode Open the menuDeleting Files Select multiple images Deleting Multiple FilesPress or to select Select, and then press the SET button Delete imagesPress or to select Lock all, and then press the SET button Protecting a Single FileProtecting All Files Thumbnail screen Open the menu Press the SET button to protect all imagesProtecting Multiple Files Protect imagesPress the SET button to rotate the image Editing ImagesRotating Still Images Changing the Image SizeCopying the Files Changing the Image with EffectsOr to select Single, then press the SET button Setting the DpofSelect Yes and then press the SET button to start copy Print the date stamp outChoosing a Startup Image Display on TV Connecting the Camera to a TVMaking Connections Connecting the Camera to a Computer with the USB Cable Connecting the Camera to a PCUsing the Card Reader Software Installation System RequirementsInstall VideoStudio 7 SE VCD Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Utilities DriversFollow the on-screen instructions to install the drivers Installing the Software DriverInstalling Ulead Photo Explorer 8 SE Basic Drive. The autorun menu appearsUlead Photo Explorer 8 SE Basic Installing VideoStudio 7 SE VCDUsing the Software Folder Structure AppendixAbout the Folder & File Name File NamingTroubleshooting Problem Cause SolutionSpecifications Ntsc / PALFunction Available List ModeCapture 0EV AEB Still Mode Select Images Using the PictBridgePrint Setting Resetting to Default Settings Starting PrintCustomer care Declaration of Conformity

Related manuals

Manual 74 pages 53.91 Kb