AGFA DC-1030I manual Troubleshooting, Problem Cause Solution

Page 58

Troubleshooting

Problem

Cause

Solution

Power does not turn on.

Battery is inserted in the

Reload battery in the correct

 

wrong direction.

direction.

 

 

 

 

Batteries are dead.

Replace or recharge

 

 

batteries.

 

 

 

 

The battery compartment

Make sure the battery

 

door is open.

compartment door is

 

 

securely closed.

 

 

 

The camera does not take

The flash is charging.

Wait for the flash to charge.

pictures.

 

 

Memory is full.

Insert a new memory card.

 

 

 

 

Memory card is not

The card may be defective,

 

formatted correctly.

use a new card.

 

 

 

Image is not recorded when

The Flash is charge.

Wait for the flash to charge.

the shutter button is

 

 

Memory is full.

Insert a new memory card.

pressed.

 

 

 

 

 

The flash does not fire.

Flash is set to OFF.

Set the flash to any mode

 

 

except off.

 

 

 

Image is blurry or out of

The camera was moving

Hold the camera steady

focus.

when the image was

when shooting picture.

 

captured.

 

 

 

 

 

The subject was beyond the

Turn the Macro mode on it

 

range within which the

the subject is within 10 cm

 

camera can focus.

or 50 cm.

 

 

Do not use Macro mode

 

 

when shooting distant

 

 

subjects.

 

 

 

Image is not displayed on

A memory card with

This camera cannot display

the LCD monitor.

non-DCIF images (recorded

non-DCIF images.

 

with other camera) is loaded.

 

 

 

 

Recorded images are not

The camera was turned

If the battery low indicator

saved in memory.

off/powered down before

appears on the LCD monitor,

 

the image was stored in

replace the battery

 

memory.

immediately.

 

 

 

Cannot transfer images to a

USB driver is not installed.

Install the USB driver before

computer after connecting

 

you connect the camera to a

the USB cable.

 

computer / turn the camera

 

 

 

 

 

52

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Page Extending battery life DisclaimerPrecautions Iii „ FCC Compliance and AdvisoryContents Appendix Using This Menu Getting StartedScope of delivery Attaching the Wrist StrapParts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries Tips Inserting the Memory CardInsert the card About Camera MemorySelect a language Setting the Display Language / Date & TimeSetting the Display Language Press the Menu button to close the menuApply the setting Setting the Date & TimeSet date and time Using the LCD Monitor REC modePlayback mode Dpof„ Playback mode „ REC modeChanging the LCD Status Power Saving Function Turning the Power On and OffPress the Power button n again to turn the power off Basic OperationSelecting the REC mode Changing the ModeSwitching between REC mode and Playback mode Set the camera to the REC mode Launch the mode paletteLaunch the ASM mode Selecting the ASM modeSet the camera to the REC mode Exit the ASM modeREC menu Using the MenusChange the setting Select an itemOpen the Setup menu Setup menuREC menu list Movie Off Press the Menu n button to close the menu Setup menu listBeep SecPAL ResetNtsc Computer / PrinterHalf press the shutter button to focus the image Basic RecordingRecording Still Images Take a pictureUsing the Q mode Resolution Values Setting Image Size and QualityQuality Values Using the Zoom Function Using the Flash Using the Macro Double Using the Self-timer & Burst10 sec BurstTurn the power on, and set the camera to Using the Aperture PriorityUsing the Shutter Priority Using the Manual Exposure Setting the Movie Size Recording Movie ClipsPress the shutter button again to end recording Recording Audio ClipsPlaying Back Audio Clips Press the SET button to start recording for 30 seconds Recording a Voice MemoOpen the Playback menu Playing Back a Voice MemoSetting the White Balance Setting the MeteringOther Recording Functions Setting the AEB Setting the ISOSetting the Exposure Setting the HighlightSetting the Photo Effect Setting the SharpnessSetting Date Stamp Playing Back Images Turn the power on, and set the camera to the Playback modePlayback Press the four-way control or nTrim the image Magnifying & Trimming Still ImagesMagnify the image Save the imagePlaying a Slide Show Change the slide show settingsViewing in Thumbnail Playing the slide showDeleting Files Playback mode Open the menuDeleting a Single File Select multiple images Deleting Multiple FilesPress or to select Select, and then press the SET button Delete imagesProtecting All Files Protecting a Single FilePress or to select Lock all, and then press the SET button Thumbnail screen Open the menu Press the SET button to protect all imagesProtecting Multiple Files Protect imagesPress the SET button to rotate the image Editing ImagesRotating Still Images Changing the Image SizeCopying the Files Changing the Image with EffectsOr to select Single, then press the SET button Setting the DpofSelect Yes and then press the SET button to start copy Print the date stamp outChoosing a Startup Image Making Connections Connecting the Camera to a TVDisplay on TV Using the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable Software Installation System RequirementsInstall VideoStudio 7 SE VCD Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Utilities DriversFollow the on-screen instructions to install the drivers Installing the Software DriverInstalling Ulead Photo Explorer 8 SE Basic Drive. The autorun menu appearsUsing the Software Installing VideoStudio 7 SE VCDUlead Photo Explorer 8 SE Basic Folder Structure AppendixAbout the Folder & File Name File NamingTroubleshooting Problem Cause SolutionSpecifications Ntsc / PALFunction Available List ModeCapture 0EV AEB Still Mode Print Setting Using the PictBridgeSelect Images Resetting to Default Settings Starting PrintCustomer care Declaration of Conformity
Related manuals
Manual 74 pages 53.91 Kb
Top Page Image Contents