AGFA DC-1030I manual Inserting the Batteries, Low Battery Indicator, About Battery Type

Page 11

Inserting the Batteries

The camera is powered by two AA-size alkaline batteries or rechargeable Ni-MH (min. 2500 mAh / 1.2V) batteries.

1 Open the battery cover.

ySlide the battery cover in the direction indicated by the arrow.

2 Insert the batteries.

yInsert two AA-size batteries with the positive (+) and negative (-) poles matching the directions indicated inside the battery room.

3 Close the battery cover.

Low Battery Indicator

A low battery indicator appears on the LCD screen when the batteries are nearly exhausted. Batteries should be replaced promptly when the low battery indicator appears.

Caution

yRisk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the instructions.

yBe sure to turn off the camera power before insert or remove batteries.

yUse only Alkaline or Ni-MH battery to power this camera. Use of any other type battery is not recommended.

yReplace all batteries at the same time. Never mix old and new batteries.

yRemove batteries if you will not be using them for a long time.

yThe camera body may feel warm after extended use. This is normal.

About Battery Type

After replacing the batteries, please check the Battery Type in the setup menu ( page 18).

5

Image 11

Contents Page Disclaimer Extending battery lifePrecautions „ FCC Compliance and Advisory IiiContents Appendix Getting Started Using This MenuAttaching the Wrist Strap Scope of deliveryParts of the Camera Page Inserting the Batteries Low Battery IndicatorAbout Battery Type About Camera Memory Inserting the Memory CardInsert the card TipsPress the Menu button to close the menu Setting the Display Language / Date & TimeSetting the Display Language Select a languageSet date and time Setting the Date & TimeApply the setting REC mode Using the LCD MonitorDpof Playback modeChanging the LCD Status „ REC mode„ Playback mode Basic Operation Turning the Power On and OffPress the Power button n again to turn the power off Power Saving FunctionSet the camera to the REC mode Launch the mode palette Changing the ModeSwitching between REC mode and Playback mode Selecting the REC modeExit the ASM mode Selecting the ASM modeSet the camera to the REC mode Launch the ASM modeSelect an item Using the MenusChange the setting REC menuREC menu list Movie Setup menuOpen the Setup menu Sec Press the Menu n button to close the menu Setup menu listBeep OffComputer / Printer ResetNtsc PALTake a picture Basic RecordingRecording Still Images Half press the shutter button to focus the imageUsing the Q mode Quality Values Setting Image Size and QualityResolution Values Using the Zoom Function Using the Flash Using the Macro Burst Using the Self-timer & Burst10 sec DoubleUsing the Shutter Priority Using the Aperture PriorityTurn the power on, and set the camera to Using the Manual Exposure Recording Movie Clips Setting the Movie SizePlaying Back Audio Clips Recording Audio ClipsPress the shutter button again to end recording Playing Back a Voice Memo Recording a Voice MemoOpen the Playback menu Press the SET button to start recording for 30 secondsOther Recording Functions Setting the MeteringSetting the White Balance Setting the Highlight Setting the ISOSetting the Exposure Setting the AEBSetting Date Stamp Setting the SharpnessSetting the Photo Effect Press the four-way control or n Turn the power on, and set the camera to the Playback modePlayback Playing Back ImagesSave the image Magnifying & Trimming Still ImagesMagnify the image Trim the imagePlaying the slide show Change the slide show settingsViewing in Thumbnail Playing a Slide ShowDeleting a Single File Playback mode Open the menuDeleting Files Delete images Deleting Multiple FilesPress or to select Select, and then press the SET button Select multiple imagesPress or to select Lock all, and then press the SET button Protecting a Single FileProtecting All Files Protect images Press the SET button to protect all imagesProtecting Multiple Files Thumbnail screen Open the menuChanging the Image Size Editing ImagesRotating Still Images Press the SET button to rotate the imageChanging the Image with Effects Copying the FilesPrint the date stamp out Setting the DpofSelect Yes and then press the SET button to start copy Or to select Single, then press the SET buttonChoosing a Startup Image Display on TV Connecting the Camera to a TVMaking Connections Connecting the Camera to a Computer with the USB Cable Connecting the Camera to a PCUsing the Card Reader System Requirements Software InstallationUtilities Drivers Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Install VideoStudio 7 SE VCDDrive. The autorun menu appears Installing the Software DriverInstalling Ulead Photo Explorer 8 SE Basic Follow the on-screen instructions to install the driversUlead Photo Explorer 8 SE Basic Installing VideoStudio 7 SE VCDUsing the Software File Naming AppendixAbout the Folder & File Name Folder StructureProblem Cause Solution TroubleshootingNtsc / PAL SpecificationsMode Function Available ListCapture 0EV AEB Still Mode Select Images Using the PictBridgePrint Setting Starting Print Resetting to Default SettingsCustomer care Declaration of Conformity

Related manuals

Manual 74 pages 53.91 Kb