AGFA DC-1030I manual Using the Zoom Function

Page 28

Using the Zoom Function

Your camera has a combination of optical and digital zoom functions that allows you to zoom in on far away subjects or zoom out for a wide angle shot.

The optical zoom is achieved by mechanically adjusting the lens of the camera. The digital zoom enlarges or shrinks the image using a software process.

1	Select the zoom setting, and point the
	camera at the subject.
2	Press the zoom button (n) to compose the
	image.
	[W]: zoom out for a wide-angle shot.
	[T] : zoom in for a telephoto shot.

yWhen the zoom button is pressed, the zoom bar appears on the LCD monitor.

yWhen the optical zoom (o) factor is at maximum, zooming stops temporarily. Press the [T] again, the camera switches to the digital zoom (p) automatically and zooming continues.

yThe digital zoom (p) will not activate in movie recording.

3 Press shutter button to take a picture.

Tips

yDigital zoom works by enlarging the center portion of an image through a software interpolation process.

yThe digital zoom is used to achieve magnification levels up to approx. 4 times.

22

Image 28

Contents Page Extending battery life DisclaimerPrecautions Iii „ FCC Compliance and AdvisoryContents Appendix Using This Menu Getting StartedScope of delivery Attaching the Wrist StrapParts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries Inserting the Memory Card Insert the cardTips About Camera MemorySetting the Display Language / Date & Time Setting the Display LanguageSelect a language Press the Menu button to close the menuApply the setting Setting the Date & TimeSet date and time Using the LCD Monitor REC modePlayback mode Dpof„ Playback mode „ REC modeChanging the LCD Status Turning the Power On and Off Press the Power button n again to turn the power offPower Saving Function Basic OperationChanging the Mode Switching between REC mode and Playback modeSelecting the REC mode Set the camera to the REC mode Launch the mode paletteSelecting the ASM mode Set the camera to the REC modeLaunch the ASM mode Exit the ASM modeUsing the Menus Change the settingREC menu Select an itemOpen the Setup menu Setup menuREC menu list Movie Press the Menu n button to close the menu Setup menu list BeepOff SecReset NtscPAL Computer / PrinterBasic Recording Recording Still ImagesHalf press the shutter button to focus the image Take a pictureUsing the Q mode Resolution Values Setting Image Size and QualityQuality Values Using the Zoom Function Using the Flash Using the Macro Using the Self-timer & Burst 10 secDouble BurstTurn the power on, and set the camera to Using the Aperture PriorityUsing the Shutter Priority Using the Manual Exposure Setting the Movie Size Recording Movie ClipsPress the shutter button again to end recording Recording Audio ClipsPlaying Back Audio Clips Recording a Voice Memo Open the Playback menuPress the SET button to start recording for 30 seconds Playing Back a Voice MemoSetting the White Balance Setting the MeteringOther Recording Functions Setting the ISO Setting the ExposureSetting the AEB Setting the HighlightSetting the Photo Effect Setting the SharpnessSetting Date Stamp Turn the power on, and set the camera to the Playback mode PlaybackPlaying Back Images Press the four-way control or nMagnifying & Trimming Still Images Magnify the imageTrim the image Save the imageChange the slide show settings Viewing in ThumbnailPlaying a Slide Show Playing the slide showDeleting Files Playback mode Open the menuDeleting a Single File Deleting Multiple Files Press or to select Select, and then press the SET buttonSelect multiple images Delete imagesProtecting All Files Protecting a Single FilePress or to select Lock all, and then press the SET button Press the SET button to protect all images Protecting Multiple FilesThumbnail screen Open the menu Protect imagesEditing Images Rotating Still ImagesPress the SET button to rotate the image Changing the Image SizeCopying the Files Changing the Image with EffectsSetting the Dpof Select Yes and then press the SET button to start copyOr to select Single, then press the SET button Print the date stamp outChoosing a Startup Image Making Connections Connecting the Camera to a TVDisplay on TV Using the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable Software Installation System RequirementsInstalling the Software Install Ulead Photo Explorer 8 SE BasicInstall VideoStudio 7 SE VCD Utilities DriversInstalling the Software Driver Installing Ulead Photo Explorer 8 SE BasicFollow the on-screen instructions to install the drivers Drive. The autorun menu appearsUsing the Software Installing VideoStudio 7 SE VCDUlead Photo Explorer 8 SE Basic Appendix About the Folder & File NameFolder Structure File NamingTroubleshooting Problem Cause SolutionSpecifications Ntsc / PALFunction Available List ModeCapture 0EV AEB Still Mode Print Setting Using the PictBridgeSelect Images Resetting to Default Settings Starting PrintCustomer care Declaration of Conformity

Related manuals

Manual 74 pages 53.91 Kb