AGFA DC-1030I manual Iii, FCC Compliance and Advisory

Page 4

FCC Compliance and Advisory

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.) this device may not cause harmful interference, and 2.) this device must accept any interference received, including interference that may cause unsatisfactory operation.

This equipment has been tested and found to comply with the limits for a Class B peripheral, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment to an outlet on a circuit different from that to which the receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. When shielded interface cables have been provided with the product or when specified additional components or accessories have elsewhere been designated to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulations.

iii

Image 4

Contents Page Extending battery life DisclaimerPrecautions Iii „ FCC Compliance and AdvisoryContents Appendix Using This Menu Getting StartedScope of delivery Attaching the Wrist StrapParts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries Inserting the Memory Card Insert the cardTips About Camera MemorySetting the Display Language / Date & Time Setting the Display LanguageSelect a language Press the Menu button to close the menuApply the setting Setting the Date & TimeSet date and time Using the LCD Monitor REC modePlayback mode Dpof„ Playback mode „ REC modeChanging the LCD Status Turning the Power On and Off Press the Power button n again to turn the power offPower Saving Function Basic OperationChanging the Mode Switching between REC mode and Playback modeSelecting the REC mode Set the camera to the REC mode Launch the mode paletteSelecting the ASM mode Set the camera to the REC modeLaunch the ASM mode Exit the ASM modeUsing the Menus Change the settingREC menu Select an itemOpen the Setup menu Setup menuREC menu list Movie Press the Menu n button to close the menu Setup menu list BeepOff SecReset NtscPAL Computer / PrinterBasic Recording Recording Still ImagesHalf press the shutter button to focus the image Take a pictureUsing the Q mode Resolution Values Setting Image Size and QualityQuality Values Using the Zoom Function Using the Flash Using the Macro Using the Self-timer & Burst 10 secDouble BurstTurn the power on, and set the camera to Using the Aperture PriorityUsing the Shutter Priority Using the Manual Exposure Setting the Movie Size Recording Movie ClipsPress the shutter button again to end recording Recording Audio ClipsPlaying Back Audio Clips Recording a Voice Memo Open the Playback menuPress the SET button to start recording for 30 seconds Playing Back a Voice MemoSetting the White Balance Setting the MeteringOther Recording Functions Setting the ISO Setting the ExposureSetting the AEB Setting the HighlightSetting the Photo Effect Setting the SharpnessSetting Date Stamp Turn the power on, and set the camera to the Playback mode PlaybackPlaying Back Images Press the four-way control or nMagnifying & Trimming Still Images Magnify the imageTrim the image Save the imageChange the slide show settings Viewing in ThumbnailPlaying a Slide Show Playing the slide showDeleting Files Playback mode Open the menuDeleting a Single File Deleting Multiple Files Press or to select Select, and then press the SET buttonSelect multiple images Delete imagesProtecting All Files Protecting a Single FilePress or to select Lock all, and then press the SET button Press the SET button to protect all images Protecting Multiple FilesThumbnail screen Open the menu Protect imagesEditing Images Rotating Still ImagesPress the SET button to rotate the image Changing the Image SizeCopying the Files Changing the Image with EffectsSetting the Dpof Select Yes and then press the SET button to start copyOr to select Single, then press the SET button Print the date stamp outChoosing a Startup Image Making Connections Connecting the Camera to a TVDisplay on TV Using the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable Software Installation System RequirementsInstalling the Software Install Ulead Photo Explorer 8 SE BasicInstall VideoStudio 7 SE VCD Utilities DriversInstalling the Software Driver Installing Ulead Photo Explorer 8 SE BasicFollow the on-screen instructions to install the drivers Drive. The autorun menu appearsUsing the Software Installing VideoStudio 7 SE VCDUlead Photo Explorer 8 SE Basic Appendix About the Folder & File NameFolder Structure File NamingTroubleshooting Problem Cause SolutionSpecifications Ntsc / PALFunction Available List ModeCapture 0EV AEB Still Mode Print Setting Using the PictBridgeSelect Images Resetting to Default Settings Starting PrintCustomer care Declaration of Conformity

Related manuals

Manual 74 pages 53.91 Kb