Arcam AVP700 manual Remote control

Remote control

The CR80 remote control is a multi-function unit that controls the AVP700 and up to seven other devices. The instructions on this page only refer to the control of the Arcam AVP700.

For information on using the remote control for other devices, and a full list of features, see the instruction booklet supplied with the CR80.

Device selection

IMPORTANT: Press the ‘AMP’ button first to operate the AVP700.

Source selection

DVD – DVD input SAT – Satellite input

VCR – toggle between the VCR and AUX inputs CD – CD player input

TAPE – Tape (monitor) input AV – AV input

MCH – DVD-A (multi-channel) input FM – FM tuner input

AM – AM tuner input

Press the relevant button once to select input; press and hold to select the analogue input if a digital input is present.

MUTE

Press once to mute the main system. Press again (or use VOL +/–) to un-mute.

VOLUME +/–

Adjusts the volume.

MODE

SET
	SELECT DEVICE
CBL	DVD	VCR	TV
SAT	CD	AMP	AUX
1 DVD		2 SAT	3 VCR
4 CD		5 AUX	6 TAPE
7 TUN		8 AV	9 MCH
MUTE		0 FM	AM

LAST

THX

SLEEP

VOL FXCH

A–B

SUB

GUIDEEXIT

On/Stand-by

This allows the AVP700 to be put into and taken out of stand-by remotely.

THX

In Zone 2, use this button to enable ‘Follow Zone 1’ mode.

Note that the AVP700 does not support THX processing.

FX (DSP effects mode)

Use this button to cycle through effects modes for two-channel sources.

SUB (Sub woofer trim)

Allows a temporary trim of the sub woofer

level. Press SUB, then adjust using the 3 4 buttons on the navigation panel.

Use this button to cycle through available surround modes.

INFO

Press to change the RDS display mode for the tuner.

P- / P+ (Tune/Preset Down/Up)

If the tuner is in PRESET mode, then these buttons decrease/increase the preset selection. If the tuner is in TUNE mode, then these buttons decrease/increase the selected frequency.

SYN (Lip sync)

Press once to adjust the Lip sync audio delay. Use the D and E navigation buttons.

Press again to exit the Lip sync function.

DIS (Display)

Press to cycle through Off/Dim/Bright illumination of the front panel display

TRM (Speaker trim)

MODE			OPEN	Navigation buttons
				Arrow buttons allow navigation around the
				menus on the AVP700.
	OK			Confirm selection by pressing OK.
				MENU
INFO			MENU	Press to select the OSD Main menu.
				Press and hold for more than two seconds to
				select the ‘Set-up Menu Index’.
				TM
P.MODE	SUBT	TITLE	MENU	Tuning mode: press this button to toggle
				between ‘preset’ and ‘tuning’ modes on the
P –	P +	TM	FAV
				tuner.
ZOOM	AUDIO	MEM	RETURN
TST	SYN	DYN	SLP
ANGLE	SETUP	STATUS	SEARCH	DYN/MEM
DIS	TRM	1	2	Used to store a radio station in a preset.
				Press once to enter store mode; use the
				P+/P- buttons to select the preset to use,
				then press this button again to confirm the
				selection.
	CR80
				1/STATUS
				Press this button to toggle between FM
				‘stereo mute’ and ‘mono’ on the tuner.
				The other buttons in this area are used for
				DVD control and do not effect the AVP700.

AVP700

E-18

Press to display the OSD Speaker trim level menu. TRM allows temporary adjustment of speaker levels, using the navigation buttons. Press again to exit the ‘Speaker Trim’ function.

NOTE Remember to install the two AA batteries supplied before trying to use your remote control.