Arcam manual Configuring the AVP700, Set-up mode, Set-up Menu Index, Navigating the Set-up menu

Page 11

Configuring the AVP700

The AVP700 ‘Set-up Menu’ has six ‘Basic’ and six ‘Advanced’ menu screens that take you through the configuration process. The ‘Basic’ menus enable you to match your AVP700 to your speakers; the ‘Advanced’ menus allow you to optimise the operation of your system. Screen shots of these menus are shown in shaded boxes on the following pages.

The best way to set the AVP700 up is using the on-screen display (OSD). To view the OSD for the initial set up, use the composite video output to connect to your TV. This is because the high quality video output has several display modes and may be incompatible with your high quality display device in its default configuration. The OSD will not be visible at all if you try to use an HDMI connection.

Set-up mode

To enter the Set-up menus press and hold the MENU button on the remote control or on the front panel, for at least two seconds. The ‘Set-up Menu Index’ is displayed on your display device.

Set-up Menu Index

The Set-up menu index page is the first page that is displayed when the Set-up menu is entered. This page allows you access to the six ‘Basic’ and six ‘Advanced’ menus.

Navigating the Set-up menu

... BY USING THE REMOTE CONTROL

The Set-up menu can be navigated by using the cursor (arrow) keys on the remote control. This is by far the easiest method.

1.To enter the Set-up menu, press and hold the MENU button (which is located immediately under the navigation buttons) for at least two seconds, until the Index page appears. (Pressing the menu button for just a short time will take

you to ‘Main Menu Screen 1’. If this happens, the Main Menu can be closed by pressing MENU for a second time.)

2. When the menu heading is highlighted, using the D and E keys will navigate between menu

OK

pages. Using this method to navigate between pages the first time the unit is being configured

will help to ensure that no pages are missed out.

 

3. Use the C and B keys to navigate up and down the menu lines.

MENU

4. To change the setting for a particular menu item, highlight the item then use the D and E keys

 

 

to cycle through the options for that item.

5.Once you have set all the menu items on a page to have values that are appropriate for your system, move the menu highlight to the top of the screen (the menu heading) and press E to move to the next menu page.

6.At any time, press the MENU button to return to the main Set-up menu index screen.

7.To save the changes you have made, return to the Set-up menu index page and highlight the ‘Save Set-up’ item at the bottom of the screen. Press the OK button to save the settings. Press OK again to exit the Set-up menu.

In addition to the above method of moving from page to page using the D and E keys, each menu page can be accessed directly from the Set-up menu index page. This is achieved by using the cursor keys to move the menu highlight to the desired page on the Index page, then pressing OK.

... BY USING THE BUTTONS ON THE FRONT PANEL OF THE AVP700

The AVP700 front panel controls can be used to configure the options. Follow the instructions given for using the remote control, in this case using the EFFECT/6 button for ‘down’, the MODE/5 button for ‘up’ and the volume control for left and right.

English

AVP700

E-11

Image 11
Contents Arcam AVP700 Pre-amp. processor Safety compliance Safety guidelinesImportant safety instructions Contents Introduction Using this handbookInserting the batteries into the remote control Before you startVideo Before making connectionsZone 2 explained AudioCables InstallationPositioning the unit AVP700 rear panelConnection of record decks Audio connectionsAnalogue audio connections Analogue pre-amplifier outputsImportant notes about HQ-video inputs and outputs Video connectionsComposite/S-video video connections Component video connectionsZone 2 connections Scart RGB 4-WIRE ConnectionControl connections Connecting the AM and FM antennasConnecting to a power supply Navigating the Set-up menu Configuring the AVP700Set-up mode Set-up Menu IndexSelect Cvbs status General Settings‘Basic’ Set-up Menus Surr L/R Small Large Sub woofer SettingsSpeaker Sizes Distance measurements for 5.1 Speaker Delay SettingsSpeaker delay settings EX Settings Level settingsADV 1 Speaker Eq ADV 2 Video SettingsADV 3 Digital Settings ‘Advanced’ Set-up MenusADV 6 Hdmi Settings Saving Settings and Exit Set-upADV 4 Zone 2 Settings ADV 5 Analogue SettingsRemote control Front panel display Switching on/offVolume control Operating your AVP700Zone HeadphonesInput selection Stereo DirectTreble/Bass Remote control buttonsEffects/FX ModeUsing the tuner Listening to the tuner in Zone Using the Main MenuUsing the remote control to enter the Main Menu Using the front panel to enter the Main MenuEffect Display Centre spreadingDigital multi-channel sources Surround modesMulti-channel source modes Two-channel source modesDSP Effects Modes Speaker positioningTroubleshooting Sound is poor or distorted Source switching changes randomly or freezes on one sourceNo Zone 2 audio when playing DTS film Unable to adjust bass and treble controlsIR Remote Codes Command Command codeSystem code Command Command code Scart S-video cable with audio back to processor Scart connectionsScart RGB cable with audio back to processor Radio interference Technical specificationsContinual improvement policy On line registration GuaranteeWorldwide Guarantee Appendix Serial programming interface Command and response formatsPower / Alimentation / Betriebsbereitschaft / Stroom Example / Exemple / Beispiel / Voorbeeld Mute / Coupure du son / Stumm / DempenDe audio- en video-ingang naar een zone wijzigen Changes the audio and video input to a zoneChange l’entrée audio et vidéo d’une zone Änderung des Audio- oder Videoeingangs einer ZoneDe video-ingang voor de hoofdzone wijzigen Changes the video input for the main zoneChange l’entrée vidéo de la zone principale Änderung der Videoquelle der HauptzoneDirect mode / Mode Direct / Direktmodus / Modus Direct Navigation / Navigation / Navigation / Navigatie Effect / Effet / Effekt / EffectStore / Mémorisation / Speichern / Opslaan RDS / Système RDS / RDS / RDS Tune / Réglage / Senderabstimmung / Afstemmen
Related manuals
Manual 34 pages 61.97 Kb