MZ-R501/R501PC
Pin No. | Pin Name | I/O |
| Description | ||
|
|
|
|
| ||
99 |
| SLDW | O | Sled motor drive signal output (W) to the motor driver (IC701)/drive control signal | ||
| output (2+) |
|
| |||
|
|
|
|
|
| |
|
|
|
|
| ||
100 |
| SLCU | I | Spindle motor drive comparison signal input (U) from the motor driver (IC701) | ||
|
|
|
|
| ||
101 |
| SLCV | I | Spindle motor drive comparison signal input (V) from the motor driver (IC701) | ||
|
|
|
|
| ||
102 |
| SLCW | I | Spindle motor drive comparison signal input (W) from the motor driver (IC701) | ||
|
|
|
|
| ||
103 | DIFVDD1 | — | Power supply terminal (for DSP I/F) (+2.3 V) | |||
|
|
|
|
|
|
|
104 | DIFVSS1 | — | Ground terminal (for DSP I/F) |
|
| |
|
|
|
|
| ||
105 |
| EFMO | O | EFM encode data output for the record to the over write head drive (IC601) | ||
|
|
|
|
|
| |
106 | (MNT0) | O | Internal DSP monitor output (0) terminal | Not used (open) | ||
|
|
|
|
|
| |
107 | (MNT1) | O | Internal DSP monitor output (1) terminal | Not used (open) | ||
|
|
|
|
|
| |
108 |
| MNT2 | O | Internal DSP monitor output (2) terminal | Not used (open) | |
|
|
|
|
|
| |
109 | (MNT3) | O | Internal DSP monitor output (3) terminal | Not used (open) | ||
|
|
|
|
| ||
110 | (SENSE) | O | Internal DSP (SENS) monitor output terminal Not used (open) | |||
|
|
|
|
| ||
111 |
| (TX) | O | Record data output enable signal output monitor terminal of the internal DSP | ||
| Not used (open) |
|
| |||
|
|
|
|
|
| |
|
|
|
|
| ||
112 | (RECP) | O | Laser power changeover signal output monitor terminal Not used (open) | |||
|
|
|
|
| ||
113 | DAPVDD3 | — | Power supply terminal (for DSP block) (+1.5 V) | |||
|
|
|
|
|
| |
114 to 117 |
| NC | O | Output terminal for the external | Not used (open) | |
|
|
|
|
|
| |
118 | DRAMVSS0 | — | Ground terminal (for the external |
| ||
|
|
|
| |||
119 | DRAMVDD0 | — | Power supply terminal (for the external | |||
|
|
|
|
|
| |
120 to 138 |
| NC | O | Output terminal for the external | Not used (open) | |
|
|
|
|
| ||
139 | DRAMVDD1 | — | Power supply terminal (for the external | |||
|
|
|
|
|
| |
140 | DRAMVSS1 | — | Ground terminal (for the external |
| ||
|
|
|
|
| ||
141 | TSB MST VDD | — | Power supply terminal (for TSB master communication) (+2.8 V) | |||
|
|
|
|
| ||
142 | RMC DTCK | I/O | TSB serial data input/output with the remote commander attached headphone | |||
|
|
|
|
| ||
143 | TSB SLV VDD | — | Power supply terminal (for I/F to TSB slave communication) (+2.3 V) | |||
|
|
|
|
| ||
144 | (TSB SLVI) | I | TSB slave signal input from the remote commander attached headphone (fixed at “L”) | |||
|
|
|
|
| ||
145 | (TSB SLVO) | O | TSB slave signal output from the remote commander attached headphone | |||
Not used (open) |
|
| ||||
|
|
|
|
|
| |
|
|
|
|
|
| |
146 |
| TDI | I | Data input terminal for JTAG | Not used (open) | |
|
|
|
|
|
| |
147 |
| TMS | I | Test mode control input terminal for JTAG | Not used (open) | |
|
|
|
|
|
| |
148 |
| TCK | I | Clock input terminal for JTAG | Not used (open) | |
|
|
|
|
|
| |
149 | XTRST | I | Reset input terminal for JTAG | Not used (open) | ||
|
|
|
|
|
| |
150 |
| TDO | O | Data output terminal for JTAG | Not used (open) | |
|
|
|
|
| ||
151 | JTAGVDD | — | Power supply terminal (for JTAG) (+2.4 V) | |||
|
|
|
|
|
|
|
152 | JTAGVSS | — | Ground terminal (for JTAG) |
|
| |
|
|
|
|
| ||
153 | MCUVDD2 | — | Power supply terminal (for the microcomputer block) (+1.5 V) | |||
|
|
|
|
| ||
154 | MIFVDD0 | — | Power supply terminal (for the microcomputer I/F block) (+2.3 V) | |||
|
|
|
|
| ||
155 | MIFVSS0 | — | Ground terminal (for the microcomputer I/F block) | |||
|
|
|
|
| ||
156, 157 | TEST1, TEST0 | I | Input terminal for the main test (normally fixed at “L”) | |||
|
|
|
|
|
| |
158 |
| EVA | I | EVA/FLASH chip discrimination terminal | “L”: FLASH chip, “H”: EVA chip | |
|
|
|
|
|
|
|
159 | OPR LED | O | Not used (open) |
|
| |
|
|
|
|
| ||
160 | SSB DATA | I/O | Input/output of SSB serial data with RF amp (IC501) | |||
|
|
|
|
|
| |
161 | SSB CLK | O | SSB serial clock output to RF amp (IC501) |
| ||
|
|
|
|
| ||
162 | MCUVSS0 | — | Ground terminal (for the microcomputer block) | |||
|
|
|
|
| ||
163 | (VREC PWM) | O | Over write head control spare terminal Not used (open) | |||
|
|
|
|
| ||
164 | VL PWM | O | PWM for the laser automatic power supply voltage control signal output to the power | |||
control (IC901) |
|
| ||||
|
|
|
|
|
| |
|
|
|
|
| ||
165 | VC PWM | O | PWM signal output for the system power supply voltage control to the power control | |||
(IC901) |
|
| ||||
|
|
|
|
|
| |
|
|
|
|
| ||
166 | SPDL AUX PWM | O | PWM signal output for the spindle support to the motor driver (IC701) | |||
|
|
|
|
|
|
|
167 | XPD ADAAUX | O | Not used (open) |
|
| |
|
|
|
|
|
|
|
168 |
| NC | O | Not used (open) |
|
|
|
|
|
|
|
|
|
27