JVC GR-AX940 manual No power is supplied, Recording does not start, Animation or Time-Lapse is not

Page 45

TROUBLESHOOTINGEN45

If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and proceed as usual from the beginning.

SYMPTOM

 

POSSIBLE CAUSE(S)

POWER

 

 

No power is supplied.

 

● The battery pack has not been attached correctly

 

 

(☞ pg. 8).

 

 

● The battery pack is not charged (☞ pg. 8).

 

 

● The power supply has not been correctly connected

 

 

(☞ pg. 9).

 

 

 

The power suddenly goes off and

 

● The battery pack has completely discharged.

does not come back on by itself.

 

● Remove the cassette and disconnect the power source, then

 

 

after a few minutes, try turning the power back on. If it still

 

 

does not come on, consult your nearest JVC dealer.

 

 

 

RECORDING

 

 

Recording cannot be performed.

 

● Make sure the Erase Protection tab is in the position that

 

 

allows recording. If not, slide the tab. Some cassettes have

 

 

removable tabs. If the tab has been removed, cover the

 

 

hole with adhesive tape.

 

 

 

Recording does not start.

 

● The camcorder Power Switch has not been set to

 

 

“CAMERA” (“AUTO“ or “PRO“.) (☞ pg. 16).

 

 

 

Animation or Time-Lapse is not

 

● Before recording in the Animation mode at the very

available.

 

beginning of a tape, set the camcorder to the Recording

 

 

mode for about 5 seconds, so that the tape runs smoothly.

 

 

Using the Fade-in function at this point is a good way to

 

 

begin an animated program (☞ pg. 37).

 

 

 

PLAYBACK

 

 

The tape is running, but there is no

 

● The TV has not been set to its VIDEO mode or channel.

playback picture.

 

● If A/V connection is used, the TV’s VIDEO/TV Switch has

 

 

not been set to VIDEO.

 

 

 

Playback picture is blurred or

 

● The video heads are dirty or worn out. Consult your nearest

interrupted.

 

JVC dealer for head cleaning or replacement.

 

 

 

The counter indication is blurred

 

● This is normal.

during Still playback.

 

 

 

 

 

TAPE TRANSPORT

 

 

The tape stops during fast-forward or

 

● The Counter Memory Function has been activated

rewind.

 

(☞ pg. 40).

Rewinding or fast-forwarding cannot

● The tape is already fully wound on one reel or the other.

be performed.

 

Page 44 Page 46
Image 45
Page 44 Page 46
Contents For Customer Use GR-AX940Dear Customer It is recommended that youFor clock operation Power Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsTo remove the battery pack Using the battery packSlide Battery Release and pull out the battery pack For more detailsZoom Lithium Battery CR2025 x 1DC Cord for clock operationZoom out Cassette AdapterContents Supply Power PowerAttach Battery Pack Detach Battery PackDischarged Charge MarkerSwitch OFF Power Clock Lithium Battery Insertion/RemovalRemove Battery Holder Insert Battery in HolderDate/Time Settings Tape Length Setting Recording Mode SettingSET Recording Mode ContOpen Cassette Holder Loading/Unloading a CassetteINSERT/REMOVE Cassette Close Cassette HolderViewfinder Adjustment Grip AdjustmentShoulder Strap Attachment Adjust LengthTripod Mounting Attach StrapBasic Recording Power Switch PositionLoad a Cassette Start ShootingViewfinder Indications Stop RecordingPress Display Button Push the Power Zoom Lever towards T EN Recording Basic FeaturesTo check the end of the last recording Feature Quick ReviewBasic Features Feature Picture StabilizerPress P. STABILIZER. appears To brighten the scene when natural lighting is too dim Feature Video LightWhen not using the video light, turn it off to save Battery powerSnapshot Recording Advanced FeaturesTake Snapshot If you press during Record-StandbyFade/Wipe Modeengage FADE- or WIPE-STANDBYStart or END Recording Select Mode Advanced FeaturesProgram AE With Special Effects Press P.AE to cycle through the modes as shown on the leftSports SepiaND Effect Nega/Posi Negative/PositivePress the Select Dial to display the Menu Screen Date/Time InsertSelect the Desired Mode Access Title MenuInstant Titles RETURN. Then press the Select Dial to close Menu ScreenUsing Menu For Detailed Adjustment Make SettingEND Setting Menu Screen Available Using The Menu Button Menu Screen Available Using The Select DialDemo Mode is set to on and the Menu Screen is closed Tally lamp comes on to signal the start of recordingAllows you to set the current date and time pg Recording pgAccess Manual Exposure Access Exposure MenuAdjust Exposure END Adjustment of ExposurePatterns that are regularly repeated FocusingAccess Manual Focus Access Focus MenuAdjust Focus END Adjustment of FocusAccess White Balance Adjustment White Balance AdjustmentSET Function Parameters To Return To Automatic White BalanceManual White Balance Operation Enter SettingSET Manual White Balance To Change The Tint For RecordingAccess INT. Time Menu Self-TimerStart Delayed Recording To Cancel Self-TimerTime-Lapse AnimationRewind or Fast-Forward the tape Playback Basic PlaybackPlay Back Stop PlaybackActivate Manual Tracking TrackingFeature Still Playback Playback FeaturesFeature Shuttle Search Feature Counter Memory FunctionUsing The Cassette Adapter EN41 Insert BatteryCassette Adapter VHS Playpak Basic Connections And Tape Dubbing When connecting the cables, open this coverBasic Connections Connection For Tape DubbingTape Dubbing Clean Lens Cleaning The CamcorderAfter Use Remove EyepieceRecording does not start No power is suppliedAnimation or Time-Lapse is not AvailableAn error number i.e. E03 appears Review or Retake modeDuring recording, the indications do not appear Tape will not ejectClock Battery Warning White Balance Mode IndicatorTape Remaining Time Displayed and the tape remaining time warning48EN Power Switch Battery Release Switch Video Light SwitchDC in Jack Connectors w to r are located beneath the cover Tally Lamp Power LampPg , 9 Index TermsTo prevent damage and prolong service life When using the AC Power Adapter/Charger in areasOther than the USA To avoid hazardAvoid using the unit For safety, do notDuring use Store cassettesConnectors Provided Accessories Optional AccessoriesGeneral Alimentacion AlimentaciónColocacion DE LA Bateria Indicador de cargaDeslice Battery Release y extraiga la batería Utilización de la bateríaPara extraer la batería EN for Servicing Only in U.S.A Warranty Only in U.S.A. EN57 Memo Memo GR-AX940
Top Page Image Contents