JVC GR-DV3000 specifications 68 EN, Select Scenes, Dissolve, Wipe Door

68 EN USING THE REMOTE CONTROL UNIT (cont.)

Program

	I N	OUT MODE	Random
1 – – – – : – –		~	Assemble
2		~	Editing
3		~
			Menu
4		~

5~

6~

7		~
8		~
	T I ME CODE	– – : – –
	TOTAL	0 0 : 00

Remote sensor

PLAY

FADE/WIPE

EFFECT

EDIT IN/OUTR.A.EDIT

CANCEL ON/OFF

Fader And Wipe Menu (available only for Random Assemble Editing)

You can also use the fade/wipe effects on page 37.

DISSOLVE

The new scene gradually appears as the old one gradually disappears.

WIPE — CORNER

The new scene wipes in over the previous one from the upper right corner to the lower left corner.

WIPE — WINDOW

The next scene gradually wipes in from the center of the screen toward the corners, covering the previous scene.

WIPE — SLIDE

The next scene gradually wipes in over the previous one from right to left.

WIPE — DOOR

The previous scene wipes out from the center to the right and left, like a door being pushed open to reveal the next scene.

WIPE — SCROLL

The new scene wipes in over the last one from the bottom of the screen to the top.

WIPE — SHUTTER

The new scene wipes in over the previous one from the center toward the top and bottom of the screen.

SELECT SCENES

4 Point the remote control at the camcorder’s remote sensor. Press PLAY (4) and then press R.A.EDIT ON/OFF on the remote control.

The Random Assemble Editing Menu appears.

5 If using a Fade/Wipe at the beginning of the scene, press FADE/WIPE on the remote control.

•Cycle through the effects by pressing repeatedly, and stop when the one you want is displayed.

•You cannot use a Picture Wipe/Dissolve at the beginning of Program 1.

6 At the beginning of the scene, press EDIT IN/ OUT on the remote control. The Edit-In position appears in the Random Assemble Editing Menu.

7 At the end of the scene, press EDIT IN/OUT. The Edit-Out position appears in the Random Assemble Editing Menu.

8 If using a Fade/Wipe at the end of the scene, press FADE/WIPE.

•Cycle through the effects by pressing repeatedly, and stop when the one you want is displayed.

•If you select a Fade/Wipe effect for an Edit-Out point, the effect is automatically applied to the following Edit-In point.

•You cannot use a Picture Wipe/Dissolve at the end of the last scene.

•When you use Fade/Wipe effects, that time is included in the total time (this does not apply to Picture Wipe/Dissolve).

9 If using Playback Special Effects, press EFFECT (
pg. 65).

10Repeat steps 6 through 9 to register additional scenes.

•To change previously registered points, press CANCEL on the remote control. The registered points disappear, one at a time, from the most recently registered point.

•If you are not using Fade/Wipe or Program AE with special effects, repeat steps 6 and 7 only.

NOTES:

●When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between them.

●If the search time for an in-point exceeds 5 minutes, the recording deck’s Record-Standby mode will be canceled and editing will not take place.

●If there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in the edited version.

●Since time codes register time only as accurately as seconds, the time code total time may not match the total program time exactly.

●Turning off the camcorder’s power erases all registered Edit- In and Edit-Out points.

●If you select Sepia or Monotone mode from Program AE with special effects, you cannot use the Dissolve or Black & White Fader. In this case the Dissolve or Black & White indicator begins blinking. Once the next Edit-In point is registered, the effect is turned off. To combine these effects, use Sepia or Monotone during recording, then use the Dissolve or Black & White Fader during Random Assemble Editing.

●It is not possible to use Fade/Wipe effects and Program AE with special effects during Random Assemble Editing using a DV cable.