58 EN |
| TROUBLESHOOTING (cont.) | |
| When the System Select Switch is set to “VIDEO”: | ||
|
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE(S) |
| RECORDING |
|
|
| Recording cannot be performed. |
| ● Make sure the Erase Protection tab is in the position that allows |
|
|
| recording. If not, slide the tab. Some cassettes have removable |
|
|
| tabs. If the tab has been removed, cover the hole with adhesive |
|
|
| tape ( pg. 8). |
|
|
| ● If the System Select Switch is set to “D.S.C.”, it is not possible |
|
|
| to record onto the tape. Change the Switch position to |
|
|
| “VIDEO” ( pg. 14). |
|
|
|
|
| Recording does not start. |
| ● The camcorder Power Switch has not been set to |
|
|
| “CAMERA” (“AUTO“ or “PRO.”) ( pg. 14). |
|
|
|
|
| Animation or |
| ● Before recording in the Animation mode at the very beginning |
| available. |
| of a tape, set the camcorder to the Recording mode for about 5 |
|
|
| seconds, so that the tape runs smoothly. Using the |
|
|
| function at this point is a good way to begin an animated |
|
|
| programme ( pg. 31). |
|
|
|
|
| PLAYBACK |
|
|
| The tape is running, but there is no |
| ● The TV has not been set to its VIDEO mode or channel. |
| playback picture. |
| ● If A/V connection is used, the TV’s VIDEO/TV Switch has not |
|
|
| been set to VIDEO. |
|
|
|
|
| Playback cannot be performed. |
| ● If the System Select Switch is set to “D.S.C.”, it is not possible |
|
|
| to play back a tape. Change the Switch position to “VIDEO” |
|
|
| ( pg. 35). |
|
|
|
|
| Playback picture is blurred or |
| ● The video heads are dirty or worn out. Consult your nearest |
| interrupted. |
| JVC dealer for head cleaning or replacement. |
|
|
|
|
| The counter indication is blurred during |
| ● This is normal. |
| Still playback. |
|
|
|
|
|
|
| TAPE TRANSPORT |
|
|
| The tape stops during |
| ● The Counter Memory Function has been activated ( pg. 36). |
| rewind. |
|
|
|
|
|
|
| Rewinding or |
| ● The tape is already fully wound on one reel or the other. |
| performed. |
|
|
|
|
|
|
| OTHER |
|
|
| The picture is blurred in the Quick |
| ● This is normal while recording in the LP mode. Some noise |
| Review or Retake mode. |
| may be present while recording in the SP mode ( pg. 10). |
|
|
|
|
| The date and time displays |
| ● If you remove the power source from the camcorder while the |
| disappear. |
| power is on, all settings and selections are erased. Make sure to |
|
|
| turn the camcorder’s power off before disconnecting the power |
|
|
| source. |
|
|
|
|
| The wrong date and time are displayed/ |
| ● If you have not performed Date/Time Setting ( pg. 9), the |
| recorded. |
| date and time are not displayed/recorded correctly. Be sure that |
|
|
| Date/Time setting is carried out. |
The tape will not eject.
●The battery pack is running low.
●If the LCD monitor is not open over 60 degrees, EJECT switch does not function.