JVC GY-HD200CHU manual Presetting and Recording of Time Code, Setting, Presetting time code data

Page 25

PREPARATIONS FOR OPERATION

Presetting and Recording of Time Code

The time codes from the internal time code generator can be recorded at the time of recording scenes.

•The TC/UB/CLOCK menu screen differs depending on whether the FRAME RATE item on the VIDEO FORMAT

menu screen is “60/30” or “50/25”.

There are two ways to preset the time code.

•Set from the TC/UB/CLOCK menu screen.

•Set in the LCD screen without opening the menu screen. This section explains how to set from the TC/UB/CLOCK menu screen.

* See page 46 for instructions of setting from the LCD screen.

Menu and switch settings to set the time code preset are the same as the settings below.

Setting

To preset the Time Code, make the following settings.

„TC GENE. switch Set to REC or FREE.

REC

: The data preset in the time code generator

 

runs only during recording.

 

Use this setting if it is necessary to record

 

continual time codes across different scenes.

 

* However, approximately ±1-frame varia-

 

tions may occur in scene accuracy.

FREE

: The time code starts to run from the time it is

 

preset in the time code generator.

„TC/UB/CLOCK menu screen (FRAME RATE: 60/30)

Use the DROP FRAME item to select the framing mode for the time code generator.

DROP

: The time code generator’s running method is

 

set the drop frame mode.

 

Use this setting when placing emphasis on

 

the recording time.

NON

: The time code generator’s running method is

DROP

set to the non drop frame mode.

 

Use this setting when placing emphasis on

 

the number of frames.

TC/UB/CLOCK menu screen

(FRAME RATE: 60/30)

Framing mode:

Drop frame/

Non-drop setting

MEMO

Drop frame/Non-drop frame mode

In the NTSC system, the actual number of frames per 1 second is approximately 29.97 frames, but per time code 30 frames are processed. To compensate for this differ- ence, the mode called “drop mode” drops frame 00 and 01 for every minute not divisible by 10.

The “non-drop frame mode” is when no frames are dropped and the actual time shift neglected.

„TC/UB/CLOCK menu screen (FRAME RATE: 50/25) Whether or not user’s bit data should be recorded can be selected with the UB REC item on the TC/UB/CLOCK menu screen.

TC/UB/CLOCK menu screen

(FRAME RATE: 50/25)

Presetting time code data

The time code and user’s bit data are preset on the TC/UB/ CLOCK menu screen.

1.Display the TC/UB/CLOCK menu screen.

Select the TC/UB/CLOCK item on the TOP MENU screen.

Time code (hour, min, sec, frame)

2.Set the time code (hours, minutes, seconds, frames).

1Rotate the SHUTTER dial to align the cursor (K) with TC PRESET, and then press the SHUTTER dial.

•The first digit of the time code blinks. The blinking digit is the one to be set.

2When the SHUTTER dial is pressed, the blinking digit changes.

3When the SHUTTER dial is rotated, the value of the blinking digit changes.

When the SHUTTER dial is rotated upward, the value becomes higher. When rotated downward, the value becomes smaller.

4Repeat the procedure described in 2 and 3 above to set the desired value for all digits.

5After setting the frame digit, press the SHUTTER dial to make EXECUTE blink. The setting values are con- firmed when the SHUTTER dial is pressed again.

To cancel the setting, select CANCEL and press the SHUTTER dial.

3.When all the digits are set

•Press the STATUS button to return to the normal screen

or

•Rotate the SHUTTER dial to align the cursor (K) with the PAGE BACK item, and then press the SHUTTER dial to return to the TOP MENU screen.

Presetting user’s bit data

The user’s bit data are preset with the UB PRESET item on the TC/UB/CLOCK menu screen.

The method for setting is the same as the method for setting the time code described on the left.

•The user’s bit can be specified using numerals or alpha- betic letters from 0 to F for each digit.

•To record user’s bit data, set the UB REC item to ON (Only when set to FRAME RATE 50/25).

CAUTION

It is not possible to set all the digits of the user’s bit data to “F”.

Reading of the data during playback will not be possible for an all-F setting.

Zero-resetting the Time Code or User’s Bit Data

This is performed with the TC or UB PRESET item on the TC/UB/CLOCK menu screen. (Performed separately for the time code and the user’s bit data.)

1Rotate the SHUTTER dial to align the cursor (K) with the TC or UB PRESET item, and then press the SHUTTER dial.

2Rotate the SHUTTER dial to select ZERO PRESET as the setting value, and then press the SHUTTER dial.

MEMO

When a menu screen is not being displayed, you can zero reset the time code data by simultaneously holding down the USER2 button and the STOP button for about 1 sec- ond.

44

45

Page 24 Page 26
Image 25
Page 24 Page 26
Contents For Customer Use GY-HD200U/CHU Instructions GY-HD200E/CHE GY-HD201E/CHESafety Precautions Important SafeguardsRemarque This symbol is only valid in the European Union Safety Precautions Cont’dInformation for Users on Disposal of Old Equipment European UnionSee For DC ×2/EarphoneSee pages 12, 36 SD memory card SeeContents Routine and Periodical Maintenance Precautions for Proper UsePrecautions for Use of Head Cleaning Tape Head CleaningCharacteristic CCD Phe- nomena Battery Pack to be UsedCondensation Videocassette to be UsedFront Section Zoom LensTh16 × 5.5BRMU MemoLCD Door Rear SectionRight Side Section Left Side Section Top Section Recording and Image Out- put Formats Setting Status Contents of Indications Status Screens in the Camera ModeIndications on the LCD Monitor and in the View- finder Status ScreensIndications on the LCD Monitor and in the Viewfinder Cont’d ContentsIndication Indication Contents NDF Magnified Status Indications on LCD MonitorSwitching between the LCD Screen and Viewfinder Display Alarm Message DisplayMenu Setting Screen Safety Zone Indication Camera mode onlyBasic System Attaching the Zoom Lens How to Attach the View- finderAttaching the Microphone Provided Inserting an SD Memory Card Attaching the Tripod Base OptionalAC Operation Battery OperationTurning the Power on Loading/Unloading the Cassette Setting and DisplayingDate and Time Displaying Time Code SettingDisplaying the Time and Date on the Screen Setting Presetting and Recording of Time CodePresetting time code data Presetting user’s bit dataAborting Preset Operation Presetting User’s BitAbout Time Code Mode Playing Back Time CodeViewfinder Adjustment Screen AdjustmentWhite Balance Adjustment Back Focus AdjustmentWhite Balance Adjustment Full Auto White Balance FAWSetting the Video Format White Shading AdjustmentSetting the Frame Rate Item Setting the REC ItemAudio Input Signal Selec- tion Camera SettingsScreen Size 43/169 Mode Selection Basic Recording Opera- tion Audio Input Signal Selection Cont’dMonitoring Audio during Recording About the Focus Assist FunctionRecord-Standby or Stop mode If the Record-Standby Mode Contin- uesFunction/Initial Setting Header REC FunctionSearch Playback ProcedureHeader REC Function Executing the Header REC FunctionSignal Cables Connecting the VideoConnecting the IEEE1394 Cable Displaying AlarmsHDV/DV Dubbing Dubbing with AV DevicesSettings Backup RecordingHDV/DV Dubbing Cont’d OFFShutter Speed in 24p Mode Remote Control Unit Functions ListConnect a Remote Con- trol Unit RM-LP55/RM- LP57 ConnectionMenu Screen Configura- tion TOP Menu Screen Setting Menu ScreensSetting Description Function/Setting bold characters indicate initial settingsVideo FORMAT1/2 Menu Screen Frame RateVideo FORMAT2/2 Menu Screen Initial settings U model 7.5% E model 0.0%Menu Screen AutoHigh MiddleNormal 108%Stop StandardSwitch Mode menu screen is only displayed in camera mode Switch Mode Menu ScreenREC Item Setting for Step Setting for Variable White Balance Menu ScreenAUDIO/MIC2/2 Menu Screen AUDIO/MIC1/2 Menu ScreenMIX LCD/VF1/4 Menu Screen LCD/VF2/4 menu screen can only be set in camera modeLCD/VF2/4 Menu Screen 70-80%LCD/VF3/4 Menu Screen Screen is displayed in the VTR modeLCD/VF4/4 Menu Screen TC/UB/CLOCK Menu Screen DisableHeader REC Menu Screen DropOTHERS1/2 Menu Screen TIME/DATE Menu Screen1394 OTHERS2/2 Menu ScreenSaving settings Loading a menu settings fileError displays File Manage Menu ScreenInitializing formatting an SD mem- ory card How to Use Skin DetailRotate Using the Skin Detail Function How to Use Skin Detail Cont’dOutputting Color Bars Display Status Action Blinking Pattern Remaining Battery/Tape Error Code Error Details This device Operation RemedyHow to Display the Hour Meter TroubleshootingSymptoms Remedy External Dimensions unit mm SpecificationsHDV GY-HD251 Safety Precautions Important SafeguardsRemarque Port Cable Length See Provided only for U model HD251CHEContents Routine and Periodical Maintenance Precautions for Proper UsePrecautions for Use of Head Cleaning Tape Characteristic CCD Phe- nomena Battery Pack to be UsedCondensation Videocassette to be UsedFront Section Zoom LensIris A/R Input GNDSetting, the time code always operates 4TC GENE. Time code generator setting switchAccording to the input level. When excessive Rear SectionPreset BGAIN Sensitivity selector switchRight Side Section EREC REC trigger button start/stop recordingRCA Left Side SectionTop Section Ieee Recording and Image Out- put FormatsRecording Composite Indications on the LCD Monitor and in the View- finder Viewfinder Cont’d Indications on the LCD MonitorND2 Filter OFF ND1File Full Auto ON, OFF GainNDF EXTSafety Zone OFF Safety ZoneCenter Mark OFF DV-24PABasic System Attaching the Zoom Lens How to Attach the ViewFinder Attaching the Microphone ProvidedSDHC-compliant memory cards cannot be used with this device Inserting an SD Memory CardAC Operation Battery Operation„GY-HD250U „GY-HD251ETurning the Power on Loading/Unloading the Cassette Setting and DisplayingDate and Time VTRDisplaying Time Code Time code input entered the IEEE1394 connectorDisplayed Time Code/User’s Bit Time codes are displayedContinual time codes across different scenes Presetting and Recording of Time CodeTime code starts to run from the time it is Time code generator’s running method isPlaying Back Time Code Presetting the Time Code from the LCD ScreenInternal Free REC Regen InternalSlave unit GY-HD250U/GY-HD251E/GY-HD110U/GY- HD111E Blinks when the time code cannot be synchronizedExternal TC OUTBack Focus Adjustment Screen Adjustment Viewfinder AdjustmentAdjusted Adjust the position and angle of the viewfinder White Shading Adjustment White Balance AdjustmentSet the ND filter switch according to the current lighting When correct white balance is obtained, the approximateCamera Settings Setting the Video FormatScreen Size 43/169 Mode Selection ND FilterAudio Input Signal Selec- tion Basic Recording Opera- tion Header REC Function How to set the Header REC menu screenOutputting Audio Playback ProcedureFast-Forward, Rewind SearchSignal Cables Connecting the VideoRecording Composite Video Signals from an External Device Status Screen Display on the LCD Screen or ViewfinderSynchronized Signals Using Genlock Func- tionsAdjust SC and H Phase Dubbing with AV DevicesHDV/DV Dubbing Connect a Remote Con- trol Unit RM-LP55/RM- LP57 Backup RecordingConnect a Remote Control Unit RM-LP55/RM-LP57 Cont’d Menu Screen Configura- tionMenu Screen Configuration Cont’d Setting Menu ScreensVideo FORMAT1/2 Menu Screen TOP Menu ScreenOFF ExecuteVideo FORMAT1/2 Menu Screen Cont’d Video FORMAT2/2 Menu Screen3200K Menu ScreenMiddle High108% NormalStandard White Balance Menu Screen PresetStop AUDIO/MIC1/2 Menu Screen Switch Mode Menu ScreenStep NoneLCD/VF1/4 Menu Screen AUDIO/MIC2/2 Menu ScreenMIX BlueLCD/VF3/4 Menu Screen LCD/VF2/4 Menu ScreenVoltage SECTC/UB/CLOCK Menu Screen LCD/VF4/4 Menu ScreenColor InternalTIME/DATE Menu Screen Header REC Menu ScreenOTHERS2/2 Menu Screen OTHERS1/2 Menu Screen3MIN BlinkOTHERS2/2 Menu Screen Cont’d Genlock Menu ScreenFile Manage Menu Screen 100 101If you want to change the range of colors recognized with How to Use Skin DetailSkin color detection function, follow the steps below Outputting Color Bars 104 105No HDV Signal No DV SignalSwitch Switch to VTRError Code Error Details GY-HD250/GY-HD251 Remedy Operation How to Display the Hour Meter TroubleshootingRGB? AUX input SpecificationsGenlock input HD/SD SDI outputCorrection
Top Page Image Contents