JVC YU30052-572 manual Power, Camera

Page 12
•The tally lamp lights while recording is in progress, and “REC ” appears in the viewfinder.
•If you want to turn the tally lamp off, see page 27.
STOP RECORDING
•The power indicator lights and the camcorder enters the Record–Standby Mode.
•The scene you’re aimed at appears on the viewfinder screen, with the word “PAUSE” superimposed upon it.
START SHOOTING
LOAD A CASSETTE

12EN

 

RECORDING Basic Recording

 

LENS COVER

NOTE:

 

You should already have performed the procedures listed

 

Switch

 

below. If not, do so before continuing.

 

 

 

 

Power (pg. 4)

 

 

Tape Length (pg. 8)

 

 

Grip Adjustment (pg. 10)

 

Slide EJECT to open the cassette holder, then insert

 

1 the cassette with the label facing out. Press PUSH to

POWER

ensure the holder is closed and locked.

Start/Stop Button

ENTER RECORD–STANDBY MODE

 

Power indicator

Slide the LENS COVER open/close switch to open

2 the lens cover, then set the power switch to

 

 

“CAMERA”.

 

 

 

 

 

 

 

 

3 Press the Recording Start/Stop button.

25min

 

 

 

Tally lamp

 

 

 

 

 

 

 

 

 

 

Tape remaining time indicator

 

Press the Recording Start/Stop button again to stop

60min

 

59min

3min

4 recording.

 

 

 

 

 

 

 

 

•The camcorder re-enters the Record-Standby

1min (Blinking)

 

2min (Blinking)

 

 

mode.

 

0min (Blinking)

*---min.....(Now calculating)

NOTES:

A cassette holder can’t be opened unless a power supply is attached.

There may be a delay after you slide EJECT until the holder opens. Do not use force.

The tape’s remaining time is displayed in the viewfinder as shown.

The indicated remaining time is approximate.

The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary according to the type of tape used.

The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been selected (pg. 8).

When using a 60–minute tape, the tape remaining time displayd will not be accurate.

“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.

If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations, the camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to “CAMERA” to turn the camcorder on again.

If you’re recording on a cassette from the middle, use the RETAKE function (pg. 14) to find the end of the last recording so you don’t erase any of it.

The LENS COVER warning blinks for about 8 seconds when the camcorder is turned on, when the cover is closed.

Image 12
Contents GR-AX860 Dear Customer This unit is produced to comply with Standard IEC PublMajor Features Power Supply PowerAttach Battery Pack Detach Battery PackCar Battery Cord Lighter Socket AP-V7E optional Car Battery Charger/Adapter 110 V to 240 BH-V3E optionalCharge marker DC OUTClock Lithium Battery Insertion/Removal Viewfinder AdjustmentEN Getting Started Date/Time Setting Tape Length Setting SET Tape LengthPress + or to move the highlight bar to Tape Length Loading/Unloading a Cassette Open Cassette HolderINSERT/REMOVE Cassette Close Cassette HolderGrip Adjustment Shoulder Strap AttachmentTripod Mounting RM-V706U Remote Control Unit Installing The BatteryPull OUT Battery Holder Replace Battery HolderPower CameraFeature PurposeOperation START/STOP Viss Retake Auto PauseVideo Light SET Video LightLight ON/AUTO/OFF EN R Ecording Advanced Features Choose Display ModeDate/Time Insert DisplaySelect Snapshot Mode Snap Shot Snap Shot ModeSnapshot Perform Snapshot RecordingDigital Image Stabilizer Exposure ControlWhite Balance Adjustment Adjust FocusAdjust White Balance White balance mode indicatorFocusing Lock FocusRelease Focus Lock FAR NearRelease Manual Focus Mode Appear and blinksGo to step Program AE With Special Effects Select EffectDeactivate Effect FAR + EFFECT/PROG.AE NearChange the setting Cinema-like 169 wide-screen effectPicture becomes sepia-tinted reddish brown monochrome Creating the look of an old photographReserve Effect Start RecordingEND Recording FADE/WIPEDissolve Scroll Wipe Auto Select onlyWindow Wipe Auto Select only Door Wipe Auto Select onlyUsing Menu For Detailed Adjustment Make SettingChange Settings Select Function AT SUB MenuJlip ID no Access Instant Title Menu Screen Select Preset TitleDisplay Preset Title Instant TitlesAccess Character SET Menu END Character SettingInput Characters FAR Near MenuTally lamp START/STOP INT. Time REC TimeRelease Animation Mode Check Your WorkCassette Adapter Insert Cassette in AdapterPlay Back on Connected VCR Remove Cassette from AdapterTo Audio and Video connectors Cable provided ConnectorsConnect Camcorder to VCR Connect Camcorder to TVPlayba CK Basic Playback Rewind or Fast-forward the tapeLoad a Cassette PlaybackPlayback Features Tracking PLAY/PAUSE Counter R/M REW Stop Pause PlayRandom Assemble Editing R.A.Edit PLAY/PAUSETo Audio out To Video out Cable provided To AudioConnect the editing cable to the R.A. Edit connector SET Remote to Operate VCROperate the VCR Connect toEditin G Engage VCR’S RECORD-PAUSE Mode Begin Automatic EditingEND Automatic Editing Player JVC VCRIndicator Counter R/MViewfinder REW Play Insert PauseAudio dubbing indicator Viewfindere External MikeREW Play DUB42 EN D EX C o nt r o lsJlip Joint Level Interface Protocol Connector Tally Lamp Power On Indicator Video Light MicrophoneQW E R T External MIC jackBattery Pack Remaining Power Changes as follows according to the batteryPack’s remaining power level When the power isGeneral Battery Precautions Make sure the cassette bears the VHS-C markEN Cautions Symptom Other Image is out of focusAdjustment Auto/Manual adjustment Out connectorDetection, timer Controlled Dimensions X 42 H Weight Approx gGR-AX860