Panasonic VQT1H84 Clip management, Repairing and connecting clips, Repairing defective clips

Page 34
Press [MENU].
Display the thumbnail display screen.
Press [MENU].
Display the thumbnail display screen. Select the clip to be repaired.

Clip management (continued)

Repairing and connecting clips

Repairing defective clips

The defective clip indicator (yellow X ) appears in order to indicate that there is a problem in the clip such as the power having been suddenly cut off while it was being recorded. You can repair problem clips by proceeding as follows.

1

2

3

4 Using [STOP], [PLAY] and [STILL], select “OPERATION” – “REPAIR CLIP”, and press [STILL].

5 Select “YES”, and press [STILL].

6 When the completion message has

appeared, press “OK” ([STILL]).

•It is not possible to repair clips with some types of damage. These kinds of clips are identified by the red X .

Connecting incomplete clips

In some cases, clips recorded on a multiple number of P2 cards may not be recognized as a single continuous clip and may be recognized as an incomplete clip ( ! indicator) instead. At

times like this you can use the connecting function to restore the “incomplete” clip to a continuous (originally connected) clip.

1

2 Select the incomplete clip to be connected.

3

4 Using [STOP], [PLAY] and [STILL], select “OPERATION” – “RE-CONNECTION”, and press [STILL].

5 Select “YES”, and press [STILL].

6 When the completion message has

appeared, press “OK” ([STILL]).

A clip is recognized as incomplete when:

•A clip recorded on a multiple number of P2 cards has been copied separately from one card and then from another or other cards.

•A clip recorded on a multiple number of cards has first been copied separately from one card and then from another or other cards onto a hard drive and then written back onto the P2 cards.

•A long clip lasting more than 5 minutes in the DVCPRO HD format (10 or so minutes in the DVCPRO50 format or 20 or so minutes in the DVCPRO DV format) has first been copied to a hard drive and then written back onto the P2 cards.

•Normally, thumbnails with the incomplete clip mark are displayed side by side.

•If only parts of incomplete clips separated into 3 or more have been connected, the incomplete clip marks will remain on the screen until all the clips which make up the original clip are connected.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Operating Instructions Memory Card Portable RecorderMemory Card Portable Recorder For Battery PackRead this first Rating plate is on the underside of the unitNotification Canada Declaration of ConformityFCC Warning For USA-California OnlySoftware information for this product Important Safety Instructions Contents Basic operations on the setting menus Drive USB Host modeDrive 1394 Host mode Setting menu configuration List of setting menusOutputting the data to the external monitor How to use the unitFor playback Introduction Editing Editing by connecting the unit to a PCAG-HPG10 this unit Hard drive P2 card AG-HPG10 this unit P2 cardReferences About this manualReferences are shown as Accessories Before useName of the parts Operation areaMechanism area and input/output connector area Output CH 1 Audio CH Video HD/SD-SDI Component OUTPower Charge Charging the batteryConnect the AC cable to the power outlet ChargingConnecting and disconnecting the power cable Installing and removing the power supplyInstalling and removing the battery InsertionHold down Power for at least 2 seconds Turning the power on and offUsing the LCD monitor Basic operationsMenu operations Operations performed when the function buttons are pressedPress Menu to exit the menu Operation modes Turn on the powerBasic operations Thumbnail display screenPC mode Turn the power off exit the PC modeLCD Brightness LCD monitor settingsLCD Color Level LCD ContrastPress FF or REW to set Year to Setting the calendarPress Stop to move the setting item to Month Press FF or REW to set Month to MAYP2 cards P2 card access LED and P2 card statusInserting P2 cards Select YES on the confirmation screen, and press Still Formatting P2 cardsP2 card protection Selected P2 card is now formattedP2 cards Ejecting P2 cardsConcerning P2 cards Using the User buttonsCharging the internal battery OtherInserting/ejecting SD memory cards Using SD memory cardsPrecautions for using SD memory cards Formatting SD memory cardsSaving User files on SD memory cards Using FF or REW, select the file number 1, 2, 3 orUsing Stop and PLAY, select WRITE, and press Still To re-load files from SD memory cardsPlayback formats Switching playback formatsThumbnail display Names and functions thumbnail display screen partsDisplay statuses P2 card slot numbers and hard drive statusesThumbnail display Names and functions of thumbnail display screen partsClips Slot Clips Changing the displays on the thumbnail display screenClips ExitSetting the items to be displayed To release the selection Clip managementSelecting clips Deleting clipsConnecting incomplete clips Repairing and connecting clipsRepairing defective clips Clip managementWhen the completion message has Appeared, press OK Still Copying clipsInformation on the selected clip now appears on the screen Voice memo indicatorDisplaying the clip information Information added to clipsClip meta-data If necessary, reference the clip meta-data contentsClip information Press MENU, and select Exit to exitEditing the clip information Inserting shot marks into clips Displaying the P2 card statusP2 card remaining memory or used memory and total memory Write-protect markP2 card status Slot remaining memory or used memory totalDisplaying the SD memory card information Press OK Still Press Menu to exit the procedureProxy recording is not possible with this unit Clip playback Playing back clipsClip forward/reverse Variable-speed searchesRepeat playback Rapid forward/rapid reverse playbackPlayback from text memo position Press MENU, and then select Exit using STOP, Play and StillClip playback Cursor moves hereReplacing thumbnail images Dividing and copying clips using text memosDeleting text memos Multiple number of text memos can be selectedAudio OUT CH1 Setting the outputsOutputting images to an external monitor for playback HD/SD-SDI OUTSDI OUT SET UPCMPNT/SDI SEL SDI MetadataInput recording For details, refer to setting menu Recording Setup screenRecording data on P2 cards Thumbnail screen appearsTime code displays Resetting the counter valueSlot continuous recording Waveform monitor displaysCopying data from P2 cards to the hard drive Hard drive Type a Accessory Cable optionalUSB cable optional Usable hard drives Switching to the USB Host modeTo exit the Host mode Following hard drive can be usedHard drive type Features Functions that can be used Copying data from P2 cards to the hard drive USB Host modeTypes of hard drives and usable functions Formatting the hard drive Exporting data to a hard drive in 1-card increments Switch to the USB Host mode Connect the USB hard driveInsert the P2 card Press Menu You can display the hard drive information Hard drive data displayCharacters to the partition. dataSaving Page Importing data from a hard drive to P2 cards Importing one clip at a time to a P2 cardSwitching to the 1394 Host mode Copying data from P2 cards to the hard drive Using Stop and PLAY, select the card slot, and press StillUsing Stop and PLAY, select PROPERTY, and press Still Hard drive status displaysFor a Macintosh computer Connector Editing the P2 card data USB Device mode/1394 Device modeEditing in the USB device mode Editing by means of external devicesEditing in the 1394 device mode Normal displays Screen displaysP2 Full Text Memo Mark onMark OFF InvalidScreen displays Turn Power OFF Cannot Access TargetCannot Access Card Lack of REC CapacityREC Warning Error displaysSystem Error Cannot PlayMode Check Selecting what is to be displayed on the screenALL Partial OFF List of recording/playback and output formats For system format 60 Hz regionsChannels with the Dvcpro or DV format For 50 Hz system format regionsRecorded Press Menu to display the menu. Example Basic operations on the setting menusInitializing the setting menu Press Still to set the itemSetting menu configuration CMPNT/SDI SEL SDI OUTList of setting menus Recording Setup screenPreset UB ModeUB Preset UserList of setting menus SW Mode screenPlayback Functions screen AV OUT Setup screenSetup Repeat PlayDisplay Setup screen Card Functions screen Other Functions screen English Power SaveLanguage JapaneseOption Menu screen Battery-related Q&A Troubleshooting Q&APower-related Q&A For your referenceRecording Troubleshooting Q&AEditing Playback No hot swap playbackWhen carrying the unit around, take care not to drop it Operating precautionsAC adapter and battery Doing so may adversely affect the recorded images and soundProtect the battery terminals Characteristics of the batteryAfter using the unit, always remember to remove the battery Protective caps for the connectorsDo not use benzine or paint thinners to clean the unit Updating the drivers installed in the unitMaintenance CondensationUnit Storage precautionsBattery SD memory cardsContents Audio Clip Icon Proxy Video Voice LASTCLIP.TXT Handling the data recorded on P2 cardsCards that you cannot Use Concerning the use of memory cardsCards that you can use All memory cards except the ones shown on the leftGeneral SpecificationsVideo P2 Card Slots Audio Optional PeripheralsOther INPUTS/OUTPUTS SD Card SlotWestern Zone Eastern ZoneTechnical Support

F0707K0 -M, AG-HPG10P, VQT1H84 specifications

The Panasonic VQT1H84, AG-HPG10P, and F0707K0-M are key components in Panasonic's lineup of professional solutions aimed at videographers and broadcasters. These products reflect Panasonic's commitment to innovation and quality in video capture and playback technologies.

The VQT1H84 is a comprehensive user manual for various Panasonic camcorders and audiovisual equipment. It serves as a crucial reference for users who seek to understand the intricate functionalities of their devices. The manual provides insights into settings, optimal configurations, and troubleshooting guidelines. It contains detailed explanations of key features like control menus, connectivity options, and audio settings. This resource ensures that operators can fully utilize their Panasonic products, enhancing the overall production quality.

The AG-HPG10P is a portable P2 HD portable recorder designed for professional broadcasting and digital cinematography. This compact model supports the P2 card format, allowing seamless integration of high-quality video and audio recording in various production environments. One significant feature is its dual codec capability, enabling the use of both AVC-Intra and MPEG-2 formats, which provides flexibility for different project requirements. The HPG10P also supports HDMI and SDI output, facilitating easy connection to external monitors and other equipment. Its robust design and high-capacity storage options make it ideal for on-location shoots and studio applications alike, ensuring that users can capture and playback detailed HD footage without compromising performance.

The F0707K0-M, on the other hand, typically refers to a specific part or accessory compatible with Panasonic's range of equipment. While details about this item may vary, it often pertains to the technical aspects of connectivity or enhancements in product performance. This could include components like cables, connectors, or supplementary tools designed to enhance the functionality of camcorders or recorders.

In summary, the combination of VQT1H84, AG-HPG10P, and F0707K0-M represents a cohesive ecosystem tailored for modern video production needs. With detailed user guidance, portable recording capabilities, and additional components for improved usability, Panasonic continues to establish itself as a leader in the audiovisual industry. Their commitment to quality and innovation ensures that professionals have the tools necessary to create stunning visual narratives.
Top Page Image Contents