Panasonic NV GS 330 To cancel Quick Start, ≥Set to Tape/Card Recording Mode

Page 14

Before using

Quick Start

When quick start is ON the battery power is still being consumed, even when the LCD monitor and the viewfinder are closed.

The movie camera will resume recording/pause mode about 1.7 seconds after the LCD monitor or the viewfinder is reopended.

≥Please note in quick start mode approximately half the pause recording power is being consumed. Using quick start mode will reduce the battery recording/playback time.

≥This is only activated in the following cases. ≥While using the battery

A tape or a card is inserted, while the Tape Recording Mode is set.

A card is inserted, while the Card Recording Mode is set.

≥While using the AC adaptor

quick start can be used even if a tape/card is not inserted.

≥Set to Tape/Card Recording Mode.

1Set [SETUP] >> [QUICK START] >> [ON]. (-19-)

2While the [OFF/ON] switch is still set to [ON], close the LCD monitor and retract the viewfinder.

OFF

ON

≥The Status indicator lights green and the unit goes into quick start standby mode.

≥The movie camera will not go into quick start standby unless the LCD monitor is closed and the viewfinder is retracted.

3Open the LCD monitor or extend the Viewfinder.

OFF

ON

≥The Status indicator lights red and the camera is put into recording pause approx. 1.7 seconds after it is turned on.

ªTo cancel Quick Start

1Set [SETUP] >> [QUICK START] >> [OFF]. (-19-)

≥If the [OFF/ON] switch is set to [OFF] while the unit is in quick start standby, the power turns off.

≥If the standby continues for approx. 30 minutes, then the status indicator will go off and the camera will be completely turned off.

≥In the following cases, quick start is cancelled and the power turns off.

≥When the Mode dial is moved.

≥When the battery or AC adaptor is removed. ≥When both the tape and card are removed while using the battery in Tape Recording

Mode.

≥When the card is removed while using the battery in Card Recording Mode.

≥When the camera is quick-started with the white balance on automatic, it may take some time until the white balance is adjusted if the scene being recorded has a light source different from the scene last recorded. (When the colour night view function is used, however, the white balance of the scene last recorded is retained.)

≥If the power is turned on in quick start standby, the zoom magnification becomes 1k and the picture size may differ from what it was before quick start standby.

≥If [POWER SAVE] (-65-) is set to [5 MINUTES] and the unit automatically goes into quick start standby mode, set the [OFF/ON] switch to [OFF], then to [ON] again. Also, close the LCD monitor and retract the viewfinder and then open the LCD monitor or extend the viewfinder again.

14

VQT1L48

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operating Instructions Manufacturer is not liable for loss of recorded contents Information for your safetyButton-type battery 60 oC Battery pack 60 oC Carefully observe copyright lawsMenu operation flow is indicated by in the description If you see this symbolPages for reference Before opening the CD-ROM package, please read the following Contents Optional Before usingAccessories Parts identification and handlingViewfinder -13 Tripod receptacle ≥When you remove the lens cap, press the knobs firmlyFitting the lens cap Lens hoodAdjust the belt length and the pad position Power supplyCharging the battery Grip beltRemoving the battery Connecting to the AC outletFitting the battery Charging time and recordable time How to turn on the powerHow to turn off the power Turning the camera onSetting date and time About date/timeRecharging the built-in lithium battery Using the LCD monitorUsing the viewfinder Adjusting the field of viewQuick Start To cancel Quick Start≥Set to Tape/Card Recording Mode Open the LCD monitor or extend the ViewfinderInserting/removing a cassette When the cassette holder does not Come outWhen the cassette holder cannot be housed Accidental erasure preventionInserting/removing a card Card access lampConcerning the write protection Switch on the SD Card Concerning the cardBasic joystick operations Selecting a modeHow to use the joystick Joystick and screen displayCard Playback Mode Tape playback modeCard recording mode AUTO/MANUAL/FOCUS switch is set to Auto Slide show start/pause DeleteUsing the menu screen Help modeSwitching the language To exit the Help modeTo exit the menu screen About the menu settingOperating with remote control To get back to the previous screenSet Setup Power LCD on Adjusting LCD monitor/viewfinderAdjusting the brightness and colour Level Order to increase the brightness Entire LCD monitorInstall a button-type battery Using the remote controlRemote control Concerning the button-type battery Remote control usable rangeSelecting the remote control mode Record mode Check before recordingConcerning the remaining tape time Indication on the screen On-screen display in the tape recording modeRecording on a tape Stopping blank search midway Through Recording checkBlank search function Set Advanced Picture Size select the desired picture size ≥Set to Card Recording ModeRecording still pictures onto a card Photoshot Press the button fullySelect the size of still pictures to be Recorded on a card On-screen display in the card recording modeTo record still pictures clearly Select the picture quality for Photoshot imagesDigital zoom function Concerning the focusing areaZoom in/out function About the variable speed zoom FunctionTo return to normal recording Recording yourselfBacklight compensation function ≥Extend the viewfinder to see the picture while recordingTo cancel the soft skin mode Soft skin modeTo cancel the colour night view function Colour night view functionFade in/fade out function To cancel the tele macro functionTele macro function Wind noise reduction function Anti-Ground-Shooting AGSTo Cancel the Wide/43 Function Self-timer recordingTo stop the timer midway through Wide/43 FunctionGuideline function Recording in various situations Scene modeImage stabilizer function To restore to the automatic Adjustment Recording in natural colours White balanceTo set the white balance manually Manual focus adjustmentAbout the black balance adjustment About flashing of the indicationShutter speed range Manual shutter speed/aperture adjustmentTo restore to automatic adjustment Iris/gain value rangeSettings on the audio Playback modeTo adjust volume Playing back tapeTo return to normal playback Slow-motion playback/ frame-by-frame playbackVariable-speed search function Playback on TV To display the on-screen information On the TVTo display multiple playback files Move the s /VOLr lever to switch the imagesPlaying back card About the compatibility of still picturesTo delete all files Deleting files recorded on a cardFormatting a card Move the joystick down to selectWhat is DPOF? Writing the printing data on a card Dpof settingTo complete the settings Protecting files on a cardRecording from a tape onto a card Edit modeEdit mode Copying onto a DVD recorder or a VCR DubbingUsing the DV Cable for Recording Digital Dubbing You can add music or narration to the recorded cassette To cancel the standby for recordingAudio dubbing ≥Set Basic REC Speed SP to take pictures Before recording with audio dubbingTo play back the sound recorded with Audio dubbing USB cableWhen you stop printing halfway Introduction With a PCBefore Use Names and functions of packaged ItemsSweetMovieLife 1.1E MotionDV Studio 6.0E LE for DV Check before UseOperating environment USB Driver Card reader function Install/ConnectionInstalling USB Driver Click USB DriverClick SweetMovieLife 1.1E Installing SweetMovieLife 1.1EInstalling MotionDV Studio 6.0E LE InstructionsFor Windows XP/2000 Connecting the movie camera to personal computerConfirmation before connection For Windows VistaIf a description other than Microsoft is displayed ≥Update the driver with the following procedureClick Update Driver With USB cable supplied ≥You cannot use SweetMovieLife in tape recording modeSoftware Set Basic or Advanced USB Function Motion DVDV cable DV terminal Install USB DriverWith DV cable optional ≥Refer to page -53-for the minimum requirementsStart the MSN Messenger/Windows Live Messenger When you use the movie camera as a Web CameraOthers Copying files recorded on a card to a personal computerViewing files copied from a card If you no longer need software or driver UninstallTo disconnect USB cable safely Double click the icon in task trayCopying still pictures on PC Using on MacintoshOperating environment on iMovie 4/ iMovie HD/iMovie ’08 To disconnect USB cable safelyVQT1L48 Tape Recording Menu MenuMenu list Tape Playback MenuBasic DATE/TIME -65-PROTECT Card Recording MenuCard Playback Menu Other menus Menus related to taking picturesMenus related to playback Others IndicationsConfirmatory indications Textual indicationsThere is no paper. Check the connected printer Functions cannot be used simultaneouslyThere is no ink. Check the connected printer Check the connected printerBefore requesting repair Problems and solutions Cassette cannot be inserted Original sound was erased when audio dubbing was performedScreen has changed suddenly Auto focus function does not workEven if a card is formatted, it cannot be used Push the Reset Switch is displayedPlayback picture is not clear During playback, Unplayable Card is displayedAbout condensation About the movie camera Clean the heads with the digital video head cleanerAbout dirty heads ≥If the movie camera is sprayed with suchPrepare spare batteries when going out for recording About the batteryBe sure to detach the battery after use Do not throw old battery into fireAbout the card About the AC adaptorAbout the cassette Folder structure of the cardAutomatic white balance Explanation of termsPeriodical check-ups LCD monitorWhite balance Auto focusSpecifications SpecificationsSpecifications Http//panasonic.co.jp/pavc/global/csMode F1207RA0 500 a
Top Page Image Contents