Axis Communications Q6042 PTZ Multi-Connector Cable sold separately, Function Pin Specifications

Page 57

AXIS Q6042 PTZ Dome Network Camera

Multi-Connector Cable (sold separately)

Multi-Connector Cable (sold separately)

When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller.

Connect the multi-connector cable to the product’s multi-connector. To locate the multi-connector, see Hardware Overview, on page

6 . The cable provides the following connectors:

Note

See page 64 for technical specifications.

Power connector - 3-pin terminal block used for power input. See image below. Use a limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for the audio out.

I/O terminal connector - Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to ground and auxiliary power, the I/O terminal connector provides the interface to:

Digital output — For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Port & Devices > Port Status) if the alarm device is activated.

Digital input — An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Port & Devices > Port Status).

Function

Pin

Notes

Specifications

 

 

 

 

GND

1

Ground

 

 

 

 

 

3.3 V DC Power

2

Can be used to power auxiliary equipment.

Max load:

 

 

Note: This pin can only be used as power out.

250 mA

 

 

 

 

Configurable (Input

3–6

Digital input — Connect to GND to activate, or leave

0 to +40 V DC

or Output)

 

floating (unconnected) to deactivate.

 

 

 

 

 

 

 

Digital output — Internal connection to ground when

Max load:

 

 

activated, floating (unconnected) when deactivated. If

100 mA

 

 

used with an external relay, a diode must be connected

Max voltage:

 

 

in parallel with the load, for protection against voltage

 

 

+40 V DC

 

 

transients.

 

 

 

 

 

 

 

57

Image 57
Contents Axis Q6042 PTZ Dome Network Camera Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis Q6042 PTZ Dome Network Camera Table of ContentsTechnical Specifications Network Connector Connectors and ButtonsHardware Overview Hardware OverviewMulti-connector LED IndicatorsPower Button SD Card SlotHardware Overview Midspan LED Indicators Accessing the Product Accessing the ProductAccess from a Browser Accessing the Product Access from the Internet Set the Root PasswordNetwork TCP/IP Advanced Live View Go to Setup EventsControls on the Live View Manual TriggerAMC Audio Controls Axis Media Control viewer toolbarTour Recording, on PTZ ControlsMedia Streams How to Stream H.264Media Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream Accessing Audio Streams Setting Up the Product Setting Up the ProductBasic Setup Video and Audio Video and AudioVideo Stream Pixel CounterStream Profiles Image264 Exposure Settings Camera SettingsImage Appearance White BalanceOverlay Image SettingsOverlay Image Go to Video & Audio Video Stream and select the Image tabPrivacy Mask Using Overlay Text in an Action RuleGo to Video & Audio Overlay Image Go to Events Action RulesAudio Settings Audio ModesAudio Input Audio Output Audio ClipsLive View Config Live View ConfigDefault Viewer for Browsers Go to Setup Live View Config Viewer SettingsUser Defined Links Output ButtonsAxis Q6042 PTZ Dome Network Camera Go to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomPTZ Pan Tilt Zoom Gatekeeper ConfigurationAutotracking Exclude AreasTour Recording Guard TourOsdi Zones AdvancedLimits Controls Control QueueDetectors Set Up Motion Detection WindowsDetectors Shock DetectionMotion Detection Parameters Audio DetectionAxis Q6042 PTZ Dome Network Camera Applications Install ApplicationApplications Application LicensesAxis Q6042 PTZ Dome Network Camera Events EventsSystem Setting Up an Action RuleTime PTZ ControlRecipients Fallback ActionRecipient Use with action Schedules Setting Up an Email RecipientGo to Events Recipients and click Add Go to Events Schedules and click AddGo to Events Recurrences and click Add Events RecurrencesRecordings RecordingsRecording List Continuous RecordingLanguages LanguagesSystem Options System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Date & Time Audio SupportGo to System Options Security Certificates System Options Network Basic TCP/IP SettingsAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsDNS Configuration Axis Video Hosting System AvhsHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4Smtp email QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 Bonjour StorageSD Card Network SharePorts & Devices MaintenancePorts Port StatusSupport Overview SupportSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigFile Upload Multi-Connector Cable sold separately Multi-Connector Cable sold separatelyFunction Pin Specifications Connector Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with streaming H.264Basic Setup Video & Audio Camera Settings Video and image problems, generalSettings Storage and disk management problemsCondensation in dome Technical Specifications Technical SpecificationsInstallation aid Function/group Specifications Network SecurityMaintenance PowerPerformance Considerations Axis Q6042 PTZ Dome Network Camera M2.2
Related manuals
Manual 68 pages 6.91 Kb

Q6042 PTZ specifications

The Axis Communications Q6042 PTZ is a sophisticated network camera designed for demanding surveillance environments. Known for its high-resolution imaging and advanced features, this camera is an ideal choice for monitoring large areas such as city centers, airports, and parking lots.

One of the standout features of the Q6042 is its 1080p resolution, offering crisp, detailed video quality. The camera supports H.264 compression technology, which minimizes bandwidth use and storage requirements without sacrificing image quality. This makes it very efficient for users looking to maintain high video fidelity while maximizing their network and storage capacity.

Another key characteristic of the Q6042 is its 18x optical zoom, enabling operators to zoom in on distant subjects without blurring the image. Combined with its advanced pan and tilt capabilities—offering a 360-degree continuous rotation and a tilt range of -20 to +90 degrees—the PTZ camera can cover vast areas and track moving objects with ease. This functionality is particularly useful for security personnel who need to monitor dynamic environments.

The Q6042 is also equipped with Axis' Wide Dynamic Range (WDR) technology, which enhances the camera's ability to capture clear images in challenging lighting conditions. This feature is vital when monitoring areas that experience significant contrasts in light, such as entrances and exits.

The camera is built for durability and features an IP66-rated weatherproof housing, protecting it from dust and heavy rain. It is also resistant to vandalism, making it suitable for outdoor installations where security is a prime concern.

Integrated with Axis’ Corridor Format technology, the Q6042 can be configured to monitor tall and narrow areas, optimizing the field of view for situations like hallways or alleys. This maximizes the effectiveness of surveillance and reduces the amount of unnecessary data captured.

Moreover, the Q6042 supports various network protocols and can be seamlessly integrated with other security systems. With its built-in analytics capabilities, the camera can be equipped with features such as motion detection and audio detection, allowing users to receive alerts based on specific events.

In summary, the Axis Communications Q6042 PTZ camera offers a robust solution for high-security surveillance needs, equipped with high-resolution video, extensive zoom capabilities, and advanced analytics, making it a versatile tool for modern security applications.