Axis Communications P5512 user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 43

AXIS P5512-E PTZ Dome Network Camera

System Options

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 36. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 46.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

The SD/SDHC memory card (not included) is managed on the System Options > Storage > SD Card page.

The settings under Storage Device are used to identify and monitor the status of the SD card, and to unmount the SD card before removal. Mounting is done automatically when a card is inserted. SD cards are normally preformatted when purchased, but if needed, click Format to format the card.

43

Image 43
Contents Axis P5512-E PTZ Dome Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis P5512-E PTZ Dome Network Camera Table of ContentsHardware Overview Hardware OverviewLED Indicators Hardware Overview Connectors and ButtonsStart a browser Internet Explorer, Firefox, Safari Accessing the ProductAccessing the Product Access from a BrowserSet the Root Password Accessing the Product Access from the InternetClick Use Https Go to Setup EventsLive View Controls on the Live ViewPTZ Controls Axis Media Control viewer toolbarAxis P5512-E PTZ Dome Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P5512-E PTZ Dome Network Camera Setting Up the Product Setting Up the ProductBasic Setup Pixel Counter VideoVideo Video Stream264 Click Save to apply the new settingsStream Profiles ImageWhite Balance Camera SettingsExposure Settings Image AppearanceGo to Video Video Stream and select the Image tab Image SettingsOverlay Overlay ImageGo to Events Action Rules Using Overlay Text in an Action RuleBrowser Viewer Description Live View ConfigLive View Config Default Viewer for BrowsersUser Defined Links Viewer SettingsFor more information, please see the online help PTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomGo to PTZ Guard Tour and click Add PTZ Pan Tilt Zoom GatekeeperGuard Tour Osdi ZonesLimits Operator Same as administrator but with lower priorityPTZ Pan Tilt Zoom Advanced Control QueueMotion Detection Set Up Motion Detection WindowsDetectors DetectorsMotion Detection Parameters Application Licenses Install ApplicationApplications ApplicationsAxis P5512-E PTZ Dome Network Camera Events EventsPTZ Control Setting Up an Action RuleGo to Events Action Rules and click Add Go to Events Recipients and click Add Setting Up an Email RecipientRecipients Recipient Use with actionGo to Events Schedules and click Add SchedulesRecurrences To create a new scheduleContinuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityCertificates IeeeGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Network Share MaintenanceGo to System Options Storage Click Network Share Logs & Reports SupportSupport Overview System OverviewPlain Config Reset to Factory Default SettingsFile Upload Checking the Firmware TroubleshootingTroubleshooting To upgrade, follow these instructionsProduct cannot be accessed from a browser Troubleshooting Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProblems with streaming H.264 Product is accessible locally but not externallyBasic Key frames Video and image problems, generalVideo Camera Settings Storage and disk management problemsTechnical Specifications Technical SpecificationsMemory Power Function/group Specifications System ApplicationInstallation Maintenance General CasingPerformance Considerations ConnectorsFunction/group Specifications Weight Kg 2.6 lb Included Accessories Decoder 1-user license VideoM4.3