Axis Communications P5532E user manual Network, Basic TCP/IP Settings

Page 39

AXIS P5532–E PTZ Dome Network Camera

System Options

If using a host name for the NTP server, a DNS server must be configured. See DNS Configuration on page 41.

•Set manually – Allows you to manually set date and time.

If using an NTP server, select your Time zone from the drop-down list. If required, check Automatically adjust for daylight saving time changes.

The Date & Time Format Used in Images is the date and time format displayed as a text overlay in the video stream. Use the

predefined formats or see File Naming & Date/Time Formats in the online help for information on how to create custom date and time formats. To include date and time in the overlay text, go to Video and select Include date and Include time.

Network

Basic TCP/IP Settings

The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 47) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 39.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Axis P5532-E PTZ Dome Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportSafety Information Hazard LevelsOther Message Levels Table of Contents Performance Considerations Symptoms, Possible Causes and Remedial ActionsHardware Overview Connectors and ButtonsNetwork Connector For technical specifications, seeControl Button LED IndicatorsMidspan LED Indicators SD Card SlotAccess the Product Access from a BrowserAccess from the Internet Set the Root Password Live ViewClick Create self-signed certificate Manual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbarPTZ Controls How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P5532-E PTZ Dome Network Camera Basic Setup Set Up the ProductPixel Counter Set Up Video StreamsClick Save to apply the new settings Video264 Stream ProfilesWhite Balance Camera SettingsExposure Settings Image AppearanceOverlay Image Image SettingsDate/Time Formats in the online help To enable overlays OverlayGo to Video Overlay Image Privacy MaskBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsGo to Setup Live View Config User Defined LinksOutput Buttons Preset Positions PTZ Pan Tilt ZoomGatekeeper Limits Guard TourOsdi Zones AdvancedControls Control Queue Operator Same as administrator but with lower priorityMotion Detection Parameters Set Up Motion Detection WindowsDetectors Motion DetectionLow level 0% Default valuesHigh level 100% Medium level 50%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P5532-E PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesActions TriggersAdd Recipients Create SchedulesRecipient Types Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingUsers To log in again and be configured to use this functionalitySystem Options SecurityCA Certificate Date & TimeIeee CertificatesNetwork Basic TCP/IP SettingsLinux/Unix example Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 Linux/Unix syntaxHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM Smtp emailSD Card StorageRTP/H.264 BonjourGo to System Options Storage Click Network Share MaintenanceNetwork Share Format SD CardLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P5532-E PTZ Dome Network Camera Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Video Camera SettingsCondensation in dome Storage and disk management problemsTechnical Specifications Connectors Function/group Specifications System ApplicationMaintenance Installation aids Memory PowerPerformance Considerations Function/group Specifications VideoM3.2
Top Page Image Contents