Axis Communications P5532E user manual Triggers, Actions

Page 33

AXIS P5532–E PTZ Dome Network Camera

Events

For more information, see the online help .

Triggers

Available action rule triggers and conditions include:

Applications – Use installed applications to trigger the rule. See Applications on page 30.

Detectors

-Motion Detection – Trigger the rule when motion is detected. See Motion Detection on page 28.

Hardware

-Fan – Trigger the rule if the fan is malfunctioning. This can for example be used to send maintenance notifications.

-Network – Trigger the rule if network connection is lost or restored. This can for example be used to start recording to the SD card.

-Temperature – Trigger the rule if the temperature falls outside or inside the operating range of the product. This can for example be used to send maintenance notifications.

Input Signal

-Manual Trigger – Trigger the rule using the Manual Trigger button in the Live View page. See Controls on the Live View Page on page 11 . This can for example be used to validate actions during product installation and configuration.

PTZ

Storage

-Available – Trigger the rule when the storage device is unmounted or removed. This can for example be used to send maintenance notifications.

-Full – Trigger the rule when the storage device is full. Under normal operation, the oldest recordings will be overwritten to prevent the storage device from becoming full.

-Locked – Trigger the rule if the storage device is locked (write protected).

System

-System Initializing – Trigger the rule when the product is being started. This can for example be used to send a notification when the product restarts.

Time

-Recurrence – Trigger the rule periodically. See Set Up Recurrences on page 35. This can for example be used to upload an image every 5 minutes.

-Use Schedule – Trigger the rule according to the selected schedule. See Create Schedules on page 34.

Actions

Available actions include:

Day/Night Vision Mode – Set day mode (IR cut filter on) or night mode (IR cut filter off).

PTZ Control

-Preset Position – Go to a preset position.

-Guard Tour – Start a guard tour. See Guard Tour on page 25.

33

Image 33
Contents Axis P5532-E PTZ Dome Network Camera Legal Considerations About this documentLiability Intellectual Property RightsLearn More SupportSafety Information Hazard LevelsOther Message Levels Table of Contents Performance Considerations Symptoms, Possible Causes and Remedial ActionsNetwork Connector Connectors and ButtonsFor technical specifications, see Hardware OverviewMidspan LED Indicators LED IndicatorsSD Card Slot Control ButtonAccess the Product Access from a BrowserAccess from the Internet Set the Root Password Live ViewClick Create self-signed certificate Controls on the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerPTZ Controls How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P5532-E PTZ Dome Network Camera Basic Setup Set Up the ProductClick Save to apply the new settings Set Up Video StreamsVideo Pixel Counter264 Stream ProfilesExposure Settings Camera SettingsImage Appearance White BalanceDate/Time Formats in the online help To enable overlays Image SettingsOverlay Overlay ImageGo to Video Overlay Image Privacy MaskDefault Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons Preset Positions PTZ Pan Tilt ZoomGatekeeper Osdi Zones Guard TourAdvanced LimitsControls Control Queue Operator Same as administrator but with lower priorityDetectors Set Up Motion Detection WindowsMotion Detection Motion Detection ParametersHigh level 100% Default valuesMedium level 50% Low level 0%Go to Setup Applications Install ApplicationApplications Application LicensesAxis P5532-E PTZ Dome Network Camera Events Set Up Action RulesConvert Event Types to Action Rules Go to Events Action Rules and click AddActions TriggersAdd Recipients Create SchedulesRecipient Types Go to Events Recurrences and click Add Set Up RecurrencesRecording List RecordingsContinuous Recording Go to Recordings ListSystem Options To log in again and be configured to use this functionalitySecurity UsersIeee Date & TimeCertificates CA CertificateNetwork Basic TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 Axis Internet Dynamic DNS ServiceLinux/Unix syntax Linux/Unix exampleDNS Configuration Advanced TCP/IP SettingsNTP Configuration Host Name ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM can be disabled under System Options Network UPnPTM QoS Quality of ServiceSmtp email UPnPTMRTP/H.264 StorageBonjour SD CardNetwork Share MaintenanceFormat SD Card Go to System Options Storage Click Network ShareSupport Overview SupportSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsScripting File UploadAxis P5532-E PTZ Dome Network Camera Upgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Video Camera Settings Key framesCondensation in dome Storage and disk management problemsTechnical Specifications Maintenance Installation aids Function/group Specifications System ApplicationMemory Power ConnectorsPerformance Considerations Function/group Specifications VideoM3.2