Axis Communications P5532E user manual Storage, RTP/H.264, Bonjour, Mount and Unmount SD Card

Page 44

AXIS P5532–E PTZ Dome Network Camera

System Options

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent data corruption, the SD card should always be unmounted before it is ejected.

Note

For SD card recommendations see www.axis.com

The Axis product supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC or SDXC card with speed class 10.

The following SD card file systems are supported:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — supported by most operating systems for personal computers.

The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card.

To avoid filling the card, it is recommended to remove recordings continuously. Under General Settings, select Remove recordings older than and select the number of days or weeks.

To stop writing to the card and protect recordings from being removed, select Lock under General Settings.

Mount and Unmount SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The SD card is automatically mounted when the card is inserted into the Axis product or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted.

To unmount the SD card:

1.Open the Axis product’s webpages and go to Setup > System Options > Storage.

2.Click SD Card.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Axis P5532-E PTZ Dome Network Camera About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreOther Message Levels Safety InformationHazard Levels Table of Contents Symptoms, Possible Causes and Remedial Actions Performance ConsiderationsConnectors and Buttons Network ConnectorFor technical specifications, see Hardware OverviewLED Indicators Midspan LED IndicatorsSD Card Slot Control ButtonAccess from the Internet Access the ProductAccess from a Browser Click Create self-signed certificate Set the Root PasswordLive View Go to Setup Events Controls on the Live ViewAxis Media Control viewer toolbar Manual TriggerPTZ Controls Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis P5532-E PTZ Dome Network Camera Set Up the Product Basic SetupSet Up Video Streams Click Save to apply the new settingsVideo Pixel CounterStream Profiles 264Camera Settings Exposure SettingsImage Appearance White BalanceImage Settings Date/Time Formats in the online help To enable overlaysOverlay Overlay ImagePrivacy Mask Go to Video Overlay ImageConfigure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionOutput Buttons Go to Setup Live View ConfigUser Defined Links Gatekeeper Preset PositionsPTZ Pan Tilt Zoom Guard Tour Osdi ZonesAdvanced LimitsControls Operator Same as administrator but with lower priority Control QueueSet Up Motion Detection Windows DetectorsMotion Detection Motion Detection ParametersDefault values High level 100%Medium level 50% Low level 0%Install Application Go to Setup ApplicationsApplications Application LicensesAxis P5532-E PTZ Dome Network Camera Set Up Action Rules EventsConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers ActionsRecipient Types Add RecipientsCreate Schedules Set Up Recurrences Go to Events Recurrences and click AddRecordings Recording ListContinuous Recording Go to Recordings ListTo log in again and be configured to use this functionality System OptionsSecurity UsersDate & Time IeeeCertificates CA CertificateBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4Linux/Unix syntax Linux/Unix exampleAdvanced TCP/IP Settings DNS ConfigurationNTP Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 FTPQoS Quality of Service UPnPTM can be disabled under System Options Network UPnPTMSmtp email UPnPTMStorage RTP/H.264Bonjour SD CardMaintenance Network ShareFormat SD Card Go to System Options Storage Click Network ShareSupport Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigScripting File UploadAxis P5532-E PTZ Dome Network Camera Troubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Video and image problems, generalVideo Camera Settings Key framesStorage and disk management problems Condensation in domeTechnical Specifications Function/group Specifications System Application Maintenance Installation aidsMemory Power ConnectorsFunction/group Specifications Video Performance ConsiderationsM3.2
Top Page Image Contents