Axis Communications P8524 user manual Storage, RTP/H.264, Bonjour, Mount and Unmount SD Card

Page 40

AXIS P8524 Network Camera

System Options

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent data corruption, the SD card should always be unmounted before it is ejected.

Note

For SD card recommendations see www.axis.com

Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 10.

The following SD card file systems are supported:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — supported by most operating systems for personal computers.

The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card.

To avoid filling the card, it is recommended to remove recordings continuously. Under General Settings, select Remove recordings older than and select the number of days or weeks.

To stop writing to the card and protect recordings from being removed, select Lock under General Settings.

Mount and Unmount SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The SD card is automatically mounted when the card is inserted into the Axis product or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted.

To unmount the SD card:

1.Open the Axis product’s webpages and go to Setup > System Options > Storage.

2.Click SD Card.

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Axis P8524 Network Camera About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis P8524 Network CameraHardware Overview Shorten Sensor Unit CableConnectors and Buttons Network ConnectorConnector For technical specifications, seeLED Indicators Power ConnectorSD Card Slot Control ButtonAccess from a Browser Access the ProductAccess from the Internet Set Power Line Frequency Set the Root PasswordClick Create self-signed certificate Go to Setup Events Live ViewControls on the Live View Manual TriggerAxis Media Control viewer toolbar Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis P8524 Network Camera Set Up the Product Basic SetupSet Up Video Streams VideoPixel Counter ImageStream Profiles Click Save to apply the new settings264 Camera Settings Exposure SettingsOverlay Image AppearanceOverlay Image Go to Video Overlay ImagePrivacy Mask Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onDetectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAxis P8524 Network Camera Install Application Go to Setup ApplicationsApplications Application LicensesAxis P8524 Network Camera Set Up Action Rules EventsConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers ActionsSet Up Recurrences Add RecipientsCreate Schedules Recipient TypesGo to Events Recurrences and click Add Recordings Recording ListContinuous Recording Go to Recordings ListTo log in again and be configured to use this functionality System OptionsSecurity UsersDate & Time IeeeCertificates CA CertificateBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4Linux/Unix syntax Linux/Unix exampleAdvanced TCP/IP Settings DNS ConfigurationNTP Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 FTPQoS Quality of Service UPnPTM can be disabled under System Options Network UPnPTMSmtp email UPnPTMStorage RTP/H.264Bonjour SD CardNetwork Share Click Unmount Card can now be removedFormat SD Card To add a network sharePorts & Devices MaintenanceSupport Advanced System OverviewLogs & Reports ScriptingReset to Factory Default Settings Plain ConfigTroubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsStorage and disk management problems Storage disruptionRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Function/group Specifications System Application Installation aids General CasingPower ConnectorsConnectors Software WarrantyFunction Pin Specifications ManagementPin terminal block for power input Performance ConsiderationsAxis P8524 Network Camera Ver M3.13 Axis P8524 Network Camera
Top Page Image Contents