Axis Communications P3304 user manual LED Indicators

Page 7

AXIS P3304 Fixed Dome Network Camera

Hardware Overview

Network Connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

NOTICE

Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. All cables connecting the product to the network and that are routed outdoors or in demanding electrical environments shall be intended for their specific use. Make sure that the network devices

are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .

I/O Connector

Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to the 0 V DC reference point and power (DC output), the I/O connector provides the interface to:

•Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

•Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Power Connector

Mini DC connector. Use the supplied adapter.

Audio Connector

The Axis product has the following audio connectors:

•Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal.

•Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier . A stereo connector must be used for audio out.

For audio in, the left channel is used from a stereo signal.

Control Button

The control button is used for:

•Resetting the product to factory default settings. See page 48.

•Connecting to an AXIS Video Hosting System service. See page 42. To connect, press and hold the button for about 3 seconds until the Status LED flashes green.

•Connecting to AXIS Internet Dynamic DNS Service. See page 42. To connect, press and hold the button for about 3 seconds.

LED Indicators

LED

Color

Indication

 

 

 

Network

Green

Steady for connection to a 100 Mbit/s network. Flashes for network activity.

 

 

 

 

Amber

Steady for connection to a 10 Mbit/s network. Flashes for network activity.

 

 

 

 

Unlit

No network connection.

 

 

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Axis P3304 Fixed Dome Network Camera Equipment Modifications About this documentLiability Intellectual Property RightsLearn More SupportAxis P3304 Fixed Dome Network Camera Table of ContentsPerformance Considerations Symptoms, Possible Causes and Remedial ActionsFor technical specifications, see Connectors and ButtonsHardware Overview LED Indicators Axis P3304 Fixed Dome Network Camera Access from a Browser Access the ProductStart a browser Internet Explorer, Firefox, Safari Set the Root Password Access from the InternetClick Create self-signed certificate Controls on the Live View Live ViewPTZ Controls Axis Media Control viewer toolbarAMC Audio Controls Axis P3304 Fixed Dome Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductFocus Adjustment Video Stream Video and AudioImage Click Save to apply the new settings Resolution. Select the default resolution264 Stream Profiles Camera SettingsGo to Video & Audio Video Stream and select the Image tab Iris adjustmentView Area OverlayOverlay Image Privacy MaskGo to Video & Audio Overlay Image Audio Modes Audio SettingsAudio Input Audio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewOutput Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis P3304 Fixed Dome Network Camera Go to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom To add a guard tour Guard TourAdvanced ControlsGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionAudio Detection Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P3304 Fixed Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesAdd Recipients Set Up RecurrencesCreate Schedules Go to Recordings List RecordingsRecording List Continuous RecordingClick Save to save and start the recording Users To log in again and be configured to use this functionalitySystem Options SecurityCertificates Date & TimeIeee Audio SupportNetwork Basic TCP/IP SettingsIPv4 Address Configuration IPv6 Address ConfigurationAdvanced TCP/IP Settings Link-Local IPv4 Address Select Use the host name to set the host name manuallyNAT traversal port mapping for IPv4 Smtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Port Status MaintenancePorts & Devices PortsLogs & Reports SupportSupport Overview System OverviewPlain Config Reset to Factory Default SettingsFile Upload Check the Firmware TroubleshootingUpgrade the Firmware Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProblems with streaming H.264 Product is accessible locally but not externallyBasic Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsTechnical Specifications Memory Power Function/group Specifications System ApplicationInstallation aids MaintenanceAccessories User license, smoked transparent cover Video Function/group Specifications IncludedPerformance Considerations M2.5

P3304 specifications

The Axis Communications P3304 is a highly regarded network camera that caters to a variety of surveillance needs. Renowned for its robust performance and advanced features, the P3304 has become a popular choice for businesses and organizations seeking reliable security solutions.

One of the main features of the Axis P3304 is its exceptional image quality. Equipped with a 1/3” progressive scan RGB CMOS sensor, the camera delivers high-definition video footage with a resolution of 1280x720 pixels, ensuring that critical details are captured clearly. The camera supports multiple video streams, allowing users to optimize bandwidth usage and customize viewing options according to specific requirements.

The P3304 boasts a wide dynamic range (WDR) technology, which enables it to handle challenging lighting conditions. This feature enhances visibility in environments with bright and dark areas, making it ideal for settings like entrance foyers or retail stores, where varying lighting can make surveillance difficult. WDR ensures that both shadows and highlights are captured effectively, leading to improved overall image quality.

Additionally, the camera is equipped with Axis’ Zipstream technology, which optimizes bandwidth and storage without compromising image quality. By analyzing the scene and automatically reducing the bitrate of areas with little detail, Zipstream allows for significant savings in data storage and transmission costs, making it an efficient choice for businesses with extensive surveillance needs.

The Axis P3304 also includes features designed for enhanced security and ease of use. It is compliant with the ONVIF profile, ensuring compatibility with a wide range of video management systems. This makes integration into existing security infrastructures seamless and hassle-free. Furthermore, the camera has built-in analytics capabilities, such as motion detection and tampering alarm, which bolster its functionality and provide additional layers of security.

Durability is another hallmark of the Axis P3304. The camera is designed to operate in various environmental conditions, with an IP51 rating for ingress protection against dust and moisture. This makes it suitable for both indoor and outdoor installations.

In summary, the Axis Communications P3304 is a versatile network camera that combines high-definition video quality, advanced technologies like WDR and Zipstream, and strong durability. With its array of features tailored for security and surveillance, it provides an effective solution for a wide range of applications, meeting the demands of modern security needs efficiently.
Top Page Image Contents