Axis Communications P1214 user manual Applications, Application Licenses, Install Application

Page 28

AXIS P1214 Network Camera

Applications

Applications

Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications

Note

•It is recommended to run one application at a time.

•Avoid running applications when the built-in motion detection is active.

Application Licenses

Some applications need a license to run. Licenses can be installed in two ways:

•Automatic installation — requires access to the Internet

•Manual installation — obtain the license key from the application vendor and upload the key to the Axis product

To request a license, the Axis product serial number (S/N) is required. The serial number can be found on the product label and under System Options > Support > System Overview.

Install Application

To install and start an application:

1.Go to Setup > Applications.

2.Under Upload Application, click Browse. Locate the application file and click Upload Package.

3.Install the license (if applicable). For instructions, see the documentation provided by the application vendor.

4.Start the application. Go to page Applications, select the application in the list of installed applications and click Start.

5.Configure the application. For instructions, see the documentation provided by the application vendor.

Note

•Applications can be uploaded by product administrators.

•Applications and licenses can be installed on multiple products at the same time using AXIS Camera Management, version 3.10 and later.

To generate a log file for the application, go to Applications. Select the application and click Log.

Application Considerations

If an application is upgraded, application settings, including the license, will be removed. The license must be reinstalled and the application reconfigured.

If the Axis product’s firmware is upgraded, installed applications and their settings will remain unchanged, although this is not guaranteed by Axis Communications AB. Note that the application must be supported by the new firmware. For information about firmware upgrades, see Upgrade the Firmware.

If the Axis product is restarted, running applications will restart automatically.

If the Axis product is restored, installed applications remain unchanged but must be restarted. To start the application, go to Setup > Applications. Select the application in the list of installed applications and click Start. For information about restoring the Axis product, see Maintenance.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Axis P1214 Network Camera About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreHazard Levels Safety InformationOther Message Levels Table of Contents Connectors and Buttons Network ConnectorFor technical specifications, see RJ45 Ethernet connector with Power over Ethernet PoELED Indicators ConnectorPower Connector RJ12 ConnectorShorten Sensor Unit Cable Access from a Browser Access the ProductAccess from the Internet Set Power Line Frequency Set the Root PasswordClick Create self-signed certificate Go to Setup Events Live ViewControls on the Live View Manual TriggerAxis Media Control viewer toolbar Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis P1214 Network Camera Set Up the Product Basic SetupVideo Set Up Video StreamsPixel Counter Image Click Save to apply the new settings264 Camera Settings Exposure SettingsStream Profiles Image AppearanceDate/Time Formats in the online help To enable overlays OverlayOverlay Image Go to Video Video Stream and select the Image tabPrivacy Mask Click Save To select the image to use as overlayConfigure the Live View Default Viewer for BrowsersViewer Settings Go to Setup Live View ConfigUser Defined Links Output ButtonsFor more information about I/O ports, see I/O Ports on Detectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAxis P1214 Network Camera Install Application Go to Setup ApplicationsApplications Application LicensesAxis P1214 Network Camera Set Up Action Rules EventsConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers ActionsSet Up Recurrences Add RecipientsCreate Schedules Recipient TypesGo to Events Recurrences and click Add Recordings Recording ListContinuous Recording Go to Recordings ListTo log in again and be configured to use this functionality System OptionsSecurity UsersDate & Time IeeeCertificates CA CertificateBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4Linux/Unix syntax Linux/Unix exampleAdvanced TCP/IP Settings DNS ConfigurationNTP Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 FTPQoS Quality of Service UPnPTM can be disabled under System Options Network UPnPTMSmtp email UPnPTMStorage RTP/H.264Bonjour SD CardNetwork Share Click Unmount Card can now be removedFormat SD Card To add a network sharePorts & Devices MaintenanceSupport Advanced System OverviewLogs & Reports ScriptingReset to Factory Default Settings Plain ConfigTroubleshooting Upgrade the FirmwareFirmware To upgrade the product’s firmware Check the FirmwareEmergency Recovery Procedure Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserProblems with streaming H.264 Product is accessible locally but not externallyBasic Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalVideo Camera Settings Storage and disk management problemsTechnical Specifications Function/group Specifications Maintenance Installation aidsPower ConnectorsConnectors Function Pin SpecificationsPin terminal block for power input Performance ConsiderationsM6.3
Related manuals
Manual 104 pages 43.64 Kb

P1214 specifications

Axis Communications P1214 is a compact, high-performance network camera designed to deliver exceptional video surveillance capabilities in a variety of applications. With its advanced features and cutting-edge technology, the P1214 is ideal for both indoor and outdoor use, making it a versatile choice for security monitoring.

One of the standout features of the P1214 is its high-resolution video capability, providing crisp 720p HD video quality that allows for detailed image capture in a variety of lighting conditions. This enables users to clearly identify and monitor individuals and objects within the camera’s field of view. The camera also boasts a wide dynamic range (WDR) technology which enhances image quality in challenging lighting situations, allowing for clear details in both bright and dark areas of the scene.

The P1214 is equipped with a built-in infrared (IR) illuminator, which enables night vision capabilities. This feature allows the camera to capture video in complete darkness, providing round-the-clock surveillance. The integration of the IR illuminator ensures that the camera remains vigilant even when visibility is low, thus enhancing its overall effectiveness in security applications.

Another critical characteristic of the P1214 is its compact design. This small form factor allows for discreet installation in various locations, making it an excellent solution for areas where aesthetics matter or space is limited. The camera is also flexible in terms of installation options, featuring a range of mounting accessories to suit different environments.

The Axis P1214 utilizes Power over Ethernet (PoE) technology, simplifying installation by allowing the camera to receive power and transmit data through a single Ethernet cable. This reduces cable clutter and the need for separate power sources, making installation quicker and more efficient.

Additionally, the camera supports Axis’ unique Zipstream technology, which optimizes bandwidth and storage efficiency without compromising image quality. This intelligent compression technique significantly reduces the amount of data transferred and stored while ensuring high-quality video remains accessible when needed.

Overall, Axis Communications P1214 is a robust and feature-rich network camera suitable for a wide range of surveillance applications. With its high-definition video quality, advanced image processing technologies, compact design, and efficient installation options, the P1214 stands out as a reliable choice for enhancing security and monitoring capabilities in various settings.
Top Page Image Contents