Axis Communications P1214 Network Share, Click Unmount Card can now be removed, Format SD Card

Page 43

AXIS P1214 Network Camera

System Options

3.Click Unmount.

4.The card can now be removed.

Format SD Card

NOTICE

Formatting the SD card will remove all data and recordings stored on the card.

Important

If autoformat is enabled, only use new or empty SD cards. Any data stored on the card will be lost when the card is inserted into the Axis product.

An SD card inserted into the product can be manually formatted to one of the supported file systems. To manually format the SD card, follow these steps:

1.Insert the SD card in the SD card slot.

2.Open the Axis product’s webpages and go to Setup > System Options > Storage.

3.Click SD Card.

4.Click Format and select the desired file system.

5.Click OK to start formatting the card.

Network Share

Network share allows you to add network storage such as a NAS (network-attached storage). The NAS shall be dedicated for recordings and data from the Axis products connected to the network. For information about reference NAS devices, go to www.axis.com/products/cam_companion_software/supported.htm

Note

For NAS recommendations see www.axis.com

To add a network share:

1.Go to System Options > Storage.

2.Click Network Share.

3.Enter the IP address, DNS or Bonjour name to the host server in the Host field.

4.Enter the name of the share in the Share field. Sub folders cannot be used.

5.If required, select The share requires login and enter the user name and password.

6.Click Connect.

To clear all recordings and data from the Axis product’s folder on the designated share, click Clear under Storage Tools.

To avoid filling the share, it is recommended to remove recordings continuously. Under Recording Settings, select Remove recordings older than and select the number of days or weeks.

To stop writing to the share and protect recordings from being removed, select Lock under Recording Settings.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Axis P1214 Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportHazard Levels Safety InformationOther Message Levels Table of Contents RJ45 Ethernet connector with Power over Ethernet PoE Connectors and ButtonsNetwork Connector For technical specifications, seeRJ12 Connector LED IndicatorsConnector Power ConnectorShorten Sensor Unit Cable Access from a Browser Access the ProductAccess from the Internet Set Power Line Frequency Set the Root PasswordClick Create self-signed certificate Manual Trigger Go to Setup EventsLive View Controls on the Live ViewAxis Media Control viewer toolbar Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P1214 Network Camera Basic Setup Set Up the ProductVideo Set Up Video StreamsPixel Counter Image Click Save to apply the new settings264 Image Appearance Camera SettingsExposure Settings Stream ProfilesGo to Video Video Stream and select the Image tab Date/Time Formats in the online help To enable overlaysOverlay Overlay ImageClick Save To select the image to use as overlay Privacy MaskDefault Viewer for Browsers Configure the Live ViewOutput Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksFor more information about I/O ports, see I/O Ports on Go to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsAxis P1214 Network Camera Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P1214 Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesActions TriggersRecipient Types Set Up RecurrencesAdd Recipients Create SchedulesGo to Events Recurrences and click Add Go to Recordings List RecordingsRecording List Continuous RecordingUsers To log in again and be configured to use this functionalitySystem Options SecurityCA Certificate Date & TimeIeee CertificatesNetwork Basic TCP/IP SettingsLinux/Unix example Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 Linux/Unix syntaxHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM Smtp emailSD Card StorageRTP/H.264 BonjourTo add a network share Network ShareClick Unmount Card can now be removed Format SD CardPorts & Devices MaintenanceSupport Scripting AdvancedSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsCheck the Firmware TroubleshootingUpgrade the Firmware Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProblems with streaming H.264 Product is accessible locally but not externallyBasic Storage and disk management problems Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsTechnical Specifications Connectors Function/group SpecificationsMaintenance Installation aids PowerFunction Pin Specifications ConnectorsPerformance Considerations Pin terminal block for power inputM6.3
Related manuals
Manual 104 pages 43.64 Kb

P1214 specifications

Axis Communications P1214 is a compact, high-performance network camera designed to deliver exceptional video surveillance capabilities in a variety of applications. With its advanced features and cutting-edge technology, the P1214 is ideal for both indoor and outdoor use, making it a versatile choice for security monitoring.

One of the standout features of the P1214 is its high-resolution video capability, providing crisp 720p HD video quality that allows for detailed image capture in a variety of lighting conditions. This enables users to clearly identify and monitor individuals and objects within the camera’s field of view. The camera also boasts a wide dynamic range (WDR) technology which enhances image quality in challenging lighting situations, allowing for clear details in both bright and dark areas of the scene.

The P1214 is equipped with a built-in infrared (IR) illuminator, which enables night vision capabilities. This feature allows the camera to capture video in complete darkness, providing round-the-clock surveillance. The integration of the IR illuminator ensures that the camera remains vigilant even when visibility is low, thus enhancing its overall effectiveness in security applications.

Another critical characteristic of the P1214 is its compact design. This small form factor allows for discreet installation in various locations, making it an excellent solution for areas where aesthetics matter or space is limited. The camera is also flexible in terms of installation options, featuring a range of mounting accessories to suit different environments.

The Axis P1214 utilizes Power over Ethernet (PoE) technology, simplifying installation by allowing the camera to receive power and transmit data through a single Ethernet cable. This reduces cable clutter and the need for separate power sources, making installation quicker and more efficient.

Additionally, the camera supports Axis’ unique Zipstream technology, which optimizes bandwidth and storage efficiency without compromising image quality. This intelligent compression technique significantly reduces the amount of data transferred and stored while ensuring high-quality video remains accessible when needed.

Overall, Axis Communications P1214 is a robust and feature-rich network camera suitable for a wide range of surveillance applications. With its high-definition video quality, advanced image processing technologies, compact design, and efficient installation options, the P1214 stands out as a reliable choice for enhancing security and monitoring capabilities in various settings.
Top Page Image Contents