Axis Communications P1214 Key frames, Status and Network indicator LEDs are flashing red rapidly

Page 50

AXIS P1214 Network Camera

Troubleshooting

Lower frame rate than

See Performance Considerations on page 54.

expected

Reduce the number of applications running on the client computer.

 

 

Limit the number of simultaneous viewers.

 

Check with the network administrator that there is enough bandwidth available.

 

Check in the AMC Control Panel (H.264 tag) that video processing is NOT set to Decode only

 

key frames.

 

Lower the image resolution.

 

The maximum frames per second is dependent on the utility frequency (60/50 Hz) of the Axis

 

product. See Technical Specifications on page 51.

Status and Network indicator LEDs are flashing red rapidly

 

 

Hardware failure

Contact your Axis reseller.

Video and image problems, general

 

 

Image unsatisfactory

Check the video stream and camera settings under Setup > Video > Video Stream and Setup >

 

Video > Camera Settings.

Motion Detection triggers unexpectedly

 

 

Changes in luminance

Motion detection is based on changes in luminance in the image. This means that if there are

 

sudden changes in the lighting, motion detection may trigger mistakenly. Lower the sensitivity

 

setting to avoid problems with luminance.

Storage and disk management problems

 

 

Storage disruption

A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other

 

read or write problems occur. To identify the source of the problem, check the System Log under

 

System Options > Support > Logs & Reports. Depending on the problem, it might be necessary to

 

re-mount the storage device.

 

For information on how to set up a storage disruption alarm, see Events on page 30.

Video cannot be recorded

Check that the SD card is not write protected (that is, read only).

SD card cannot be mounted

Reformat the SD card and then click Mount.

NOTICE

Formatting the card will remove all content, including all recordings, from the SD card.

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Axis P1214 Network Camera Liability About this documentLegal Considerations Intellectual Property RightsSupport Learn MoreOther Message Levels Safety InformationHazard Levels Table of Contents For technical specifications, see Connectors and ButtonsNetwork Connector RJ45 Ethernet connector with Power over Ethernet PoEPower Connector LED IndicatorsConnector RJ12 ConnectorShorten Sensor Unit Cable Access from the Internet Access the ProductAccess from a Browser Click Create self-signed certificate Set the Root PasswordSet Power Line Frequency Controls on the Live View Go to Setup EventsLive View Manual TriggerAxis Media Control viewer toolbar Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis P1214 Network Camera Set Up the Product Basic SetupPixel Counter Set Up Video StreamsVideo 264 Click Save to apply the new settingsImage Stream Profiles Camera SettingsExposure Settings Image AppearanceOverlay Image Date/Time Formats in the online help To enable overlaysOverlay Go to Video Video Stream and select the Image tabPrivacy Mask Click Save To select the image to use as overlayConfigure the Live View Default Viewer for BrowsersUser Defined Links Viewer SettingsGo to Setup Live View Config Output ButtonsFor more information about I/O ports, see I/O Ports on Motion Detection DetectorsCamera Tampering Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAxis P1214 Network Camera Applications Install ApplicationGo to Setup Applications Application LicensesAxis P1214 Network Camera Convert Event Types to Action Rules Set Up Action RulesEvents Go to Events Action Rules and click AddTriggers ActionsCreate Schedules Set Up RecurrencesAdd Recipients Recipient TypesGo to Events Recurrences and click Add Continuous Recording RecordingsRecording List Go to Recordings ListSecurity To log in again and be configured to use this functionalitySystem Options UsersCertificates Date & TimeIeee CA CertificateBasic TCP/IP Settings NetworkLinux/Unix syntax Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 Linux/Unix exampleNTP Configuration Advanced TCP/IP SettingsDNS Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 FTPSmtp email QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMBonjour StorageRTP/H.264 SD CardFormat SD Card Network ShareClick Unmount Card can now be removed To add a network shareSupport MaintenancePorts & Devices Logs & Reports AdvancedSystem Overview ScriptingReset to Factory Default Settings Plain ConfigFirmware To upgrade the product’s firmware TroubleshootingUpgrade the Firmware Check the FirmwareProblems setting the IP address Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Product cannot be accessed from a browserBasic Product is accessible locally but not externallyProblems with streaming H.264 Video Camera Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Storage and disk management problemsTechnical Specifications Power Function/group SpecificationsMaintenance Installation aids ConnectorsConnectors Function Pin SpecificationsPin terminal block for power input Performance ConsiderationsM6.3
Related manuals
Manual 104 pages 43.64 Kb

P1214 specifications

Axis Communications P1214 is a compact, high-performance network camera designed to deliver exceptional video surveillance capabilities in a variety of applications. With its advanced features and cutting-edge technology, the P1214 is ideal for both indoor and outdoor use, making it a versatile choice for security monitoring.

One of the standout features of the P1214 is its high-resolution video capability, providing crisp 720p HD video quality that allows for detailed image capture in a variety of lighting conditions. This enables users to clearly identify and monitor individuals and objects within the camera’s field of view. The camera also boasts a wide dynamic range (WDR) technology which enhances image quality in challenging lighting situations, allowing for clear details in both bright and dark areas of the scene.

The P1214 is equipped with a built-in infrared (IR) illuminator, which enables night vision capabilities. This feature allows the camera to capture video in complete darkness, providing round-the-clock surveillance. The integration of the IR illuminator ensures that the camera remains vigilant even when visibility is low, thus enhancing its overall effectiveness in security applications.

Another critical characteristic of the P1214 is its compact design. This small form factor allows for discreet installation in various locations, making it an excellent solution for areas where aesthetics matter or space is limited. The camera is also flexible in terms of installation options, featuring a range of mounting accessories to suit different environments.

The Axis P1214 utilizes Power over Ethernet (PoE) technology, simplifying installation by allowing the camera to receive power and transmit data through a single Ethernet cable. This reduces cable clutter and the need for separate power sources, making installation quicker and more efficient.

Additionally, the camera supports Axis’ unique Zipstream technology, which optimizes bandwidth and storage efficiency without compromising image quality. This intelligent compression technique significantly reduces the amount of data transferred and stored while ensuring high-quality video remains accessible when needed.

Overall, Axis Communications P1214 is a robust and feature-rich network camera suitable for a wide range of surveillance applications. With its high-definition video quality, advanced image processing technologies, compact design, and efficient installation options, the P1214 stands out as a reliable choice for enhancing security and monitoring capabilities in various settings.
Top Page Image Contents