Bosch Appliances VG4-500I, VG4-200, VG4-300 Basic Mode Date/Time, Basic Mode Network, Dhcp

Page 71

70 en Configuring the IP AutoDomeVG4 Modular Camera System

10.2

Basic Mode: Date/Time

Device date/Device time/Device time zone

If there are multiple devices operating in your system or network, it is important to synchronize their internal clocks. For example, it is only possible to identify and correctly evaluate simultaneous recordings when all units are operating on the same time. If necessary, you can synchronize the unit with your computer's system settings.

Click the Sync to PC button to copy your computer's system time to the IP AutoDome.

Time server IP address

The IP AutoDome can receive the time signal from a time server using various time server protocols, and then use it to set the internal clock. The unit polls the time signal automatically once every minute.

Enter the IP address of a time server here.

Time server type

Select the protocol that is supported by the selected time server. Preferably, you should select the SNTP server as the protocol. This supports a high level of accuracy and is required for special applications and subsequent function extensions.

Select Time server for a time server that works with the protocol RFC 868.

10.3

Basic Mode: Network

The settings on this page are used to integrate the IP AutoDome into an existing network. Some changes only take effect after the unit is rebooted. In this case, the Set button changes to Set and Reboot.

1.Make the desired changes.

2.Click the Set and Reboot button. The IP AutoDome is rebooted and the changed settings are activated.

CAUTION!

If you change the IP address, subnet mask or gateway address, the IP AutoDome is only available under the new addresses after the reboot.

DHCP

If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you can activate acceptance of IP addresses automatically assigned to the IP AutoDome.

Certain applications (VIDOS, Bosch Video Management System, Archive Player, Configuration Manager) use the IP address for the unique assignment of the unit. If you use these applications, the DHCP server must support the fixed assignment between IP address and MAC address, and must be appropriately set up so that, once an IP address is assigned, it is retained each time the system is rebooted.

IP address

Enter the desired IP address for the IP AutoDome in this field. The IP address must be valid for the network.

Subnet mask

Enter the appropriate subnet mask for the selected IP address here.

Gateway address

If you want the unit to establish a connection to a remote location in a different subnet, enter the IP address of the gateway here. Otherwise leave the box blank (0.0.0.0).

F.01U.133.268 6.0 2010.03

User’s Manual

Bosch Security Systems, Inc.

Image 71
Contents VG4 Modular Camera System Page Table of Contents VG4 Audio Connections Keyboard Commands by Number Advanced FeaturesUsing the IP AutoDome Pelco On-Screen MenusConfiguring the IP AutoDome Troubleshooting Guide 117 Seconds and ends with a splash screen Powering OnGetting Started Establishing AutoDome ControlLCD 2Keyboard CommandsBasic Keyboard Operation To change or clear an address for a camera with an address Setting the Camera AddressFastAddress To set an address for a camera without an addressTo set or change a password locked command Setting PasswordsSpecial Passwords Password Security LevelOn-Screen Display Menu Navigation Setup MenuCamera Setup Menu OFF ATWAuto Internal60 sec Night ModeRestore DefaultsFast Lens SetupSpot ConstantPTZ Setup Menu Normal OSD Display Setup MenuMoment ARYCommunication Setup Menu Alarm I/O Setup Pressure SetupInputs LowOutputs Outputs Setup MenuOutputs Setup Alarm RelayRule Rule Setup MenuRule Setup None Language Menu Advanced Feature Setup Menu available with Series 500i onlyAdvanced Feature Setup AutoTrack TimeoutTimeout Period StabilizationInternal Temp Diagnostics MenuAlarm Status BistExtComm Error Security AccessCtfid Access Power Up Events11.1 Alarm Status Submenu 2Setting Preset Shots Common AutoDome User Commands unlockedSetting AutoPan Mode To stop a Preposition Tour 4Configuring Preposition ToursSpecifying a Shot or a Sector Title To start Preposition Tour 1 200, 300, and 500i Series6Recording Tours 300 and 500i Series only 5Programming the Inactivity OperationAlternative Control Protocols Setting FastAddress with Alternative ProtocolsUsing an American Dynamics Controller Enter FastAddress Exit Command LockFastAddress Setting FastAddress with a Pelco Keyboard 2Using a Pelco ControllerNew Fast Address Saved Setup Menu 2Pelco Keyboard Commands Pelco Protocol ModeHardware Configuration Preset Pelco Keyboard CommandsSpecial Preset Commands Pelco On-Screen Menus Bosch Menu locked Command Lock lockedPelco menu Bosch menu Setup Menu Outdoor PTZ Setup unlockedCamera Setup unlocked Pelco Camera Setup Menu provides access to camera settingsOther Menus Keyboard Commands by Number Specifying a Shot or a Sector Title, Zone Title menu Enters Zone Title menu. Refer toVG4 Modular Camera System Keyboard Commands by Number en Alarm Rule Examples Advanced FeaturesAlarm Rules 300 and 500i Series Only Controlling Alarm RulesExample 2 Advanced Alarm Rule Example 3 Advanced Alarm Rule using AutoTrack Click Output Option Click the Online Config button and then expand AlarmAutomatic AutoTrack Operation 500i Series OnlyManual AutoTrack Settings and Recommendations Consistent Light Conditions Setting AutoTrack Optimization Parameters2AutoTrack Optimization Dynamic Light ConditionsMotion Detection with Region of Interest 500i Series Only Preset positions 90 throughVirtual Masking 500i Series Only 4Privacy Masking 300 and 500i Series Only7Pre-position Tour Image Stabilization 500i Series OnlyOverview of Features Using the IP AutoDomeBelow Connecting the IP AutoDome to the PCNetwork switch to bypass the Local Area Network LAN System RequirementsAutoDome IP Connection Network Switch Computer Configuring the IP AutoDome CameraInstalling the Required Software Using the Configuration Manager 1Changing the Network SettingsInstall the software packages using the procedure below Network Settings Using the IP AutoDome Web ServerProtected Network 6The LivepageMaximum Number of Connections Protected IP AutoDomeDigital I/O View ControlIris open Audio Function Entering a Keyboard Control CommandTriggering Relay System Log / Event LogNumber Description To Enter a Keyboard Control CommandTo Set a Preset Shot Aux Control TabRecording Video Sequences To View a Preset ShotImage Resolution Saving SnapshotsConnections Audio Line Input SpecificationsWire Specifications 9VG4 Audio ConnectionsTo transmit audio via the IP connection, do the following Click the Transmit Audio radio button to enable for audioEnabling Audio Transmission 5Configuring Gain optional 10.1 Basic Mode Device Access Configuring the IP AutoDomeConfirm password PasswordDhcp 10.2 Basic Mode Date/Time10.3 Basic Mode Network Modem 10.4 Basic Mode Encoder Profile10.5Basic Mode Audio DSLStorage medium 10.6 Basic Mode Recording10.7 Basic Mode System Overview 10.8Advanced Mode IdentificationInitiator extension 10.9Advanced Mode PasswordDevice time zone 10.10 Advanced Mode Date/TimeDate format Device date/Device time10.11 Advanced Mode Display Stamping 10.13 Advanced Mode Livepage Functions 10.12 Advanced Mode Appearance10.14 Advanced Mode Logging Isdn 1B 10.15 Advanced Mode Picture Settings10.16 Advanced Mode Encoder Profile Isdn 2BCIF 10.17 Advanced Mode Encoder Streams Transmitted, select Off 10.18 Advanced Mode AudioPicture quality Network10.21 Camera Settings Group 10.23 Advanced Mode Lens 10.24 Lens Settings Group 10.22 Camera Settings Group10.26 Advanced Mode PTZ 10.27 PTZ Settings Group 10.25 Lens Settings Group10.29 Advanced Mode Display 10.30 Display Settings Group 10.28 PTZ Settings GroupTour 10.31 Display Settings GroupScene # Custom Tour 10.32 Display Settings Group10.33 Advanced Mode Alarm 10.34 Input Options Custom Tour PeriodPhysical Output 10.35 Output OptionsRule Definition Creating Alarm Rules 10.36Alarm RulesBasic Alarm Rule Example Output Option 5 Example Click the Type drop-down list and select Transmit Select Output OptionAlarm Rule 1 Example Address Advanced Alarm Rule Example using AutoTrackAudio/BiPhase 10.37Miscellaneous10.38 Logs 10.39 Advanced Mode Storage ManagementFormatting Storage Media Activating and Configuring Storage MediaLocal Media Recording includes 10.40Advanced Mode Recording ProfilesStream profile settings Deactivating Storage Media10.41 Advanced Mode Retention Time Time periods 10.42 Advanced Mode Recording SchedulerHolidays Deleting Holidays10.44 Advanced Mode Alarm Connections 10.43 Advanced Mode Recording StatusDecoder Video transmissionRemote port Video outputVCA configuration 10.45 Advanced Mode VCA10.46 Advanced Mode VCA Profiles Sensitivity MOTION+ only Aggregation time sAnalysis type Motion detector MOTION+ onlySelect Area MOTION+ only Trigger delay sMinimum object size MOTION+ only Debounce time 1 s MOTION+ onlyScene too noisy Global changeScene too bright Scene too darkSelect Area 10.47 Advanced Mode VCA Scheduled10.49 Advanced Mode Audio Alarm 10.48 Advanced Mode VCA Event triggeredSMS 10.50 Advanced Mode Alarm E-MailTest e-mail 10.51 Advanced Mode Alarm Task EditorSender name Http browser port 10.52 Advanced Mode NetworkAutomatic IP assignment DNS server addressRCP+ port Interface mode ETHEnable DynDNS Https browser portSnmp 10.53 Advanced Mode AdvancedNtcip 10.54 Advanced Mode Multicasting10.55 Advanced Mode Jpeg Posting 10.57 Advanced Mode Maintenance 10.56 Advanced Mode EncryptionDownload 10.58 Advanced Mode Licenses10.59 Advanced Mode System Overview Maintenance log11.1 VG4 AutoDome Operation and Control Troubleshooting GuideIf O.K., then If using a non-Bosch power supply If O.K., then If there is power to the AutoDome, thenNo camera control If amber LED does not light when given PTZ commands, thenCannot access user SettingsDynamics Keyboard Setting FastAddressDoes not switch If O.K., then Automatically when With an American11.2 VG4 IP AutoDome Video and Control Audio Connections with an Analog standard VG4 AutoDome Audio Connections with an IP-enabled VG4 AutoDome11.3VG4 IP AutoDome Audio Typical Audio Connections for an Analog AutoDome Problem Solution No Audio Poor Audio Problem Solution If O.K., thenProbably not the source of audio problems 328 ftUser Command Table En User Command Table VG4 Modular Camera System Group Appendix FastAddress ConversionsBlock Numerics IndexVG4 Modular Camera System Index en En Index VG4 Modular Camera System Jpeg En Index VG4 Modular Camera System PTZ En Index VG4 Modular Camera System VIP XD Page Page Bosch Security Systems, Inc
Related manuals
Manual 76 pages 38.12 Kb

VG4-500I, VG4-200, VG4-300 specifications

Bosch Appliances is renowned for its commitment to quality and innovation, and their VG4 series of ventilation hoods is no exception. The VG4-300, VG4-200, and VG4-500I models are designed to cater to various kitchen needs, providing effective air filtration while maintaining aesthetic appeal.

The VG4-300 model is characterized by its sleek design and robust performance. It features a powerful motor that delivers efficient ventilation, removing smoke, odors, and grease from your kitchen swiftly. One of the standout features is its three-speed fan system, which allows users to select the appropriate level of airflow based on cooking intensity. Additionally, the grease filter is dishwasher-safe, ensuring easy maintenance and longevity.

In contrast, the VG4-200 model is perfect for those seeking a compact yet powerful solution. Designed for smaller kitchens, it doesn’t compromise on performance. This model also offers a three-speed fan, providing sufficient airflow for everyday cooking activities. The LED lighting integrated into the design enhances visibility on your cooktop while adding a modern touch to your kitchen. With a focus on energy efficiency, the VG4-200 operates quietly, allowing for a pleasant cooking experience without distraction.

The VG4-500I model is a standout in the series, designed for larger, more demanding kitchens. With increased airflow capacity, it can handle vigorous cooking styles with ease. It also boasts an advanced filtration system that captures more airborne particles, enhancing indoor air quality. The model features a touch control panel for ease of use, giving users the ability to adjust settings seamlessly. Like its counterparts, the VG4-500I includes LED lighting and dishwasher-safe filters, making maintenance straightforward.

All three models in the VG4 series exemplify Bosch's dedication to advanced technologies. Noise reduction features ensure that the ventilation system operates quietly, allowing conversations in the kitchen without disturbance. Furthermore, the stylish and modern finishes of each model enhance kitchen aesthetics, making them suitable for any decor.

In summary, Bosch Appliances’ VG4-300, VG4-200, and VG4-500I ventilation hoods offer a range of features tailored to meet different culinary needs. From effective air filtration and energy-efficient operation to user-friendly controls and elegant designs, these models are crafted to elevate the cooking experience while ensuring a fresh and clean kitchen environment.