Axis Communications M3025-VE user manual UPnPTM, RTP/H.264, Bonjour

Page 45

AXIS M3025–VE Network Camera

System Options

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 38. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 49.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

45

Image 45
Contents Axis M3025-VE Network Camera Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis M3025-VE Network Camera Table of ContentsPerformance Considerations Network Connector Connectors and ButtonsFor technical specifications, see RJ45 Ethernet connector with Power over Ethernet PoEConnector LED IndicatorsSD Card Slot Control ButtonAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordLive View Set Power Line FrequencyControls on the Live View Click Use HttpsAxis Media Control viewer toolbar Go to Setup EventsPTZ Controls Manual TriggerAxis M3025-VE Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M3025-VE Network Camera Basic Setup Set Up the ProductVideo Click Save to apply the new settingsVideo Stream Pixel Counter264 Stream ProfilesExposure Settings Camera SettingsImage Appearance White BalanceOverlay View AreaOverlay Image Go to Video Video Stream and select the Image tabGo to Video Overlay Image Use Overlay Text in an Action RuleGo to Events Action Rules Click Add to create a new rulePrivacy Mask Default Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions PTZ Pan Tilt ZoomAdvanced Axis M3025-VE Network Camera Camera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis M3025-VE Network Camera Go to Setup Applications Install ApplicationApplications Application LicensesAxis M3025-VE Network Camera Events Set Up Action RulesConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers Input SignalDetectors HardwareAdd Recipients ActionsRecipient Types Recipient Use with action Set Up Email RecipientsCreate Schedules Set Up RecurrencesTo create a new schedule Go to Events Schedules and click AddRecording List RecordingsContinuous Recording Go to Recordings ListLanguages Security System OptionsUsers IP Address FilterIeee CertificatesGo to System Options Security Ieee Go to Setup System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkIPv6 Address Configuration IPv4 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4Smtp email QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 BonjourSD Card StorageMount and Unmount SD Card Format SD CardPorts & Devices MaintenanceNetwork Share PortsSupport Overview SupportSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsScripting File UploadAxis M3025-VE Network Camera Upgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Video Camera Settings Key framesStorage and disk management problems Problem Retrieving Additional Video StreamsStorage disruption Re-mount the storage deviceTechnical Specifications Power Function/group Specifications System ApplicationConnectors DimensionsFunction/group Specifications Included ConnectorsConnector Function Pin SpecificationsPerformance Considerations M4.5
Related manuals
Manual 22 pages 30.55 Kb