Axis Communications M1143-L user manual Media Streams, How to Stream H.264, Axis Media Control AMC

Page 12

AXIS M1143–L - User Manual

Media Streams

Media Streams

The Axis product provides several video stream formats. Your requirements and the properties of your network will determine the type you use.

The Live View page in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream profiles. Other applications and clients can access video streams directly, without going via the Live View page.

How to Stream H.264

H.264 can, without compromising image quality, reduce the size of a digital video file by more than 80% compared with the Motion JPEG format and as much as 50% more than the MPEG-4 standard. This means that much less network bandwidth and storage space are required for a video file. Or seen another way, much higher video quality can be achieved for a given bit rate.

Deciding which combination of protocols and methods to use depends on your viewing requirements, and on the properties of your network. The available options in AXIS Media Control are:

Unicast RTP

This unicast method (RTP over UDP) is used

 

 

 

for live unicast video, especially when it is

 

 

 

important to always have an up-to-date video

 

 

stream, even if some frames are dropped.

 

Unicasting is used for video-on-demand

RTP over RTSP

This unicast method (RTP tunneled over RTSP)

transmission so that there is no video traffic

on the network until a client connects and

 

is useful as it is relatively simple to configure

 

 

 

requests the stream.

 

firewalls to allow RTSP traffic.

 

 

 

Note that there are a maximum of 20

 

 

 

RTP over RTSP over HTTP

This unicast method can be used to traverse

 

simultaneous unicast connections.

 

firewalls. Firewalls are commonly configured

to

 

 

allow the HTTP protocol, thus allowing RTP to

 

 

be tunneled.

 

 

 

 

 

Multicast RTP

This method (RTP over UDP) should be used for live multicast video. The video stream is always

 

up-to-date, even if some frames are dropped.

 

 

Multicasting provides the most efficient usage of bandwidth when there are large numbers of

 

clients viewing simultaneously. A multicast cannot however, pass a network router unless the

 

router is configured to allow this. It is not possible to multicast over the Internet, for example.

 

Note also that all multicast viewers count as one unicast viewer in the maximum total of 20

 

simultaneous connections.

 

 

 

 

 

 

AXIS Media Control negotiates with the Axis product to determine the transport protocol to use. The order of priority, listed in the AMC Control Panel, can be changed and the options disabled, to suit specific requirements.

Note

H.264 is licensed technology. The Axis product includes one H.264 viewing client license. Installing additional unlicensed copies of the client is prohibited. To purchase additional licenses, contact your Axis reseller.

MJPEG

This format uses standard JPEG still images for the video stream. These images are then displayed and updated at a rate sufficient to create a stream that shows constantly updated motion.

The Motion JPEG stream uses considerable amounts of bandwidth, but provides excellent image quality and access to every image contained in the stream. The recommended method of accessing Motion JPEG live video from the Axis product is to use the AXIS Media Control in Internet Explorer in Windows.

AXIS Media Control (AMC)

AXIS Media Control (AMC) in Internet Explorer in Windows is the recommended method of accessing live video from the Axis product.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Page About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Symptoms, Possible Causes and Remedial Actions Connectors Performance ConsiderationsConnectors and Buttons Network ConnectorConnector Hardware OverviewLED Indicators SD Card SlotControl Button Color IndicationAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordLive View Controls on the Live ViewClick Use Https Manual TriggerGo to Setup Events Axis Media Control viewer toolbarPTZ Controls To show the manual trigger buttons in the Live ViewAccess the Product How to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedMedia Streams Set Up the Product Basic SetupClick Save to apply the new settings VideoVideo Stream Pixel CounterStream Profiles 264Camera Settings Exposure SettingsImage Appearance White BalanceTo configure the view area View AreaOverlay Built-in IR Illuminations LEDsOverlay Image Go to Video Overlay ImageFocus Adjustment Privacy MaskUse Overlay Text in an Action Rule Go to Events Action RulesConfigure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions PTZ Pan Tilt ZoomGuard Tour AdvancedOperator Same as administrator but with lower priority Control QueueDetectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersDetectors Install Application Go to Setup ApplicationsApplications Application LicensesApplications Set Up Action Rules EventsTriggers Go to Events Action Rules and click AddInput Signal HardwareStorage SystemAdd Recipients ActionsRecipient Types Set Up Email Recipients Create SchedulesGo to Events Schedules and click Add Set Up Recurrences Go to Events Recurrences and click AddRecordings Find RecordingsPlay Recording Go to Recordings ListExport Video Clip Continuous RecordingGo to Recordings Continuous Languages System Options SecurityUsers IP Address FilterIeee CertificatesGo to System Options Security Ieee Basic TCP/IP Settings Go to Setup System Options Security CertificatesDate & Time NetworkIPv4 Address Configuration IPv6 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 BonjourStorage SD CardMount and Unmount SD Card Format SD CardMaintenance Ports & DevicesNetwork Share PortsSupport Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigScripting File UploadSystem Options Troubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsStorage and disk management problems Storage disruptionRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Function/group Specifications Events actions InstallationMaintenance General Casing PowerConnectors Function/group Specifications WarrantyFunction Pin Specifications Performance Considerations M2.13

M1143-L specifications

Axis Communications M1143-L is a robust and versatile network camera tailored for various surveillance applications. Known for its superior image quality and smart technologies, the M1143-L is an ideal choice for both indoor and outdoor environments.

At the heart of the M1143-L is its high-resolution imaging technology, providing stunning 1080p Full HD video at up to 30 frames per second. This guarantees clear, detailed images even in challenging light conditions. The camera features Lightfinder technology, which enhances low-light performance, ensuring that critical details are captured even in near darkness. Coupled with Wide Dynamic Range (WDR) technology, the M1143-L effectively deals with challenging lighting situations, balancing light and shadow for optimal clarity.

Robust construction is another hallmark of the M1143-L. Built to withstand harsh conditions, it adheres to IP66 and NEMA 4X ratings, making it dust-tight and protected against powerful water jets. This feature makes it suitable for outdoor use, providing durability against various weather elements.

The camera also includes built-in infrared (IR) illumination, which enables it to operate effectively even in complete darkness. The IR range can reach up to 30 meters, making it a powerful ally for nighttime surveillance.

Axis Communications prioritizes user-friendliness, and the M1143-L is no exception. The camera supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted through a single cable. This reduces cable clutter while ensuring a reliable power supply. Additionally, the camera boasts an easy-to-use web-based interface for quick configuration and setup.

For enhanced security, the M1143-L supports advanced analytics and cybersecurity features. The camera can integrate with Axis’ range of video management software, offering seamless operation alongside other Axis devices. Furthermore, it is equipped with multiple user access levels, enhancing security by ensuring that only authorized personnel can access the footage.

In conclusion, Axis Communications M1143-L is a feature-rich network camera that combines high-resolution imaging, durability, and smart technologies, making it an excellent choice for a variety of surveillance needs. Its advanced features ensure reliable performance in diverse environments, providing peace of mind for users seeking top-tier security solutions.
Top Page Image Contents