Axis Communications M1143-L user manual UPnPTM, RTP/H.264, Bonjour

Page 46

AXIS M1143–L - User Manual

System Options

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 39. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 50.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Page Liability About this DocumentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Symptoms, Possible Causes and Remedial Actions Connectors Performance ConsiderationsConnector Connectors and ButtonsNetwork Connector Hardware OverviewControl Button LED IndicatorsSD Card Slot Color IndicationAccess from the Internet Access the ProductAccess from a Browser Set the Root PasswordClick Use Https Live ViewControls on the Live View Manual TriggerPTZ Controls Go to Setup EventsAxis Media Control viewer toolbar To show the manual trigger buttons in the Live ViewAccess the Product Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedMedia Streams Set Up the Product Basic SetupVideo Stream Click Save to apply the new settingsVideo Pixel CounterStream Profiles 264Image Appearance Camera SettingsExposure Settings White BalanceOverlay To configure the view areaView Area Built-in IR Illuminations LEDsOverlay Image Go to Video Overlay ImageUse Overlay Text in an Action Rule Focus AdjustmentPrivacy Mask Go to Events Action RulesViewer Settings Configure the Live ViewDefault Viewer for Browsers Browser Viewer DescriptionOutput Buttons Go to Setup Live View ConfigUser Defined Links For more information about I/O ports, see I/O Ports onGuard Tour Preset PositionsPTZ Pan Tilt Zoom AdvancedOperator Same as administrator but with lower priority Control QueueMotion Detection DetectorsCamera Tampering Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersDetectors Applications Install ApplicationGo to Setup Applications Application LicensesApplications Triggers Set Up Action RulesEvents Go to Events Action Rules and click AddStorage Input SignalHardware SystemActions Add RecipientsRecipient Types Create Schedules Set Up Email RecipientsGo to Events Schedules and click Add Set Up Recurrences Go to Events Recurrences and click AddPlay Recording RecordingsFind Recordings Go to Recordings ListContinuous Recording Export Video ClipGo to Recordings Continuous Languages Users System OptionsSecurity IP Address FilterCertificates IeeeGo to System Options Security Ieee Date & Time Basic TCP/IP SettingsGo to Setup System Options Security Certificates NetworkAssign IP Address Using ARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration ARP/PingAxis Internet Dynamic DNS Service requires IPv4 Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM BonjourMount and Unmount SD Card StorageSD Card Format SD CardNetwork Share MaintenancePorts & Devices PortsSystem Overview SupportSupport Overview Logs & ReportsScripting Reset to Factory Default SettingsPlain Config File UploadSystem Options Emergency Recovery Procedure TroubleshootingUpgrade the Firmware Check the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video Camera SettingsRe-mount the storage device Storage and disk management problemsStorage disruption Reformat the SD card and then click MountTechnical Specifications Maintenance General Casing Function/group Specifications Events actionsInstallation PowerFunction/group Specifications Warranty ConnectorsFunction Pin Specifications Performance Considerations M2.13

M1143-L specifications

Axis Communications M1143-L is a robust and versatile network camera tailored for various surveillance applications. Known for its superior image quality and smart technologies, the M1143-L is an ideal choice for both indoor and outdoor environments.

At the heart of the M1143-L is its high-resolution imaging technology, providing stunning 1080p Full HD video at up to 30 frames per second. This guarantees clear, detailed images even in challenging light conditions. The camera features Lightfinder technology, which enhances low-light performance, ensuring that critical details are captured even in near darkness. Coupled with Wide Dynamic Range (WDR) technology, the M1143-L effectively deals with challenging lighting situations, balancing light and shadow for optimal clarity.

Robust construction is another hallmark of the M1143-L. Built to withstand harsh conditions, it adheres to IP66 and NEMA 4X ratings, making it dust-tight and protected against powerful water jets. This feature makes it suitable for outdoor use, providing durability against various weather elements.

The camera also includes built-in infrared (IR) illumination, which enables it to operate effectively even in complete darkness. The IR range can reach up to 30 meters, making it a powerful ally for nighttime surveillance.

Axis Communications prioritizes user-friendliness, and the M1143-L is no exception. The camera supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted through a single cable. This reduces cable clutter while ensuring a reliable power supply. Additionally, the camera boasts an easy-to-use web-based interface for quick configuration and setup.

For enhanced security, the M1143-L supports advanced analytics and cybersecurity features. The camera can integrate with Axis’ range of video management software, offering seamless operation alongside other Axis devices. Furthermore, it is equipped with multiple user access levels, enhancing security by ensuring that only authorized personnel can access the footage.

In conclusion, Axis Communications M1143-L is a feature-rich network camera that combines high-resolution imaging, durability, and smart technologies, making it an excellent choice for a variety of surveillance needs. Its advanced features ensure reliable performance in diverse environments, providing peace of mind for users seeking top-tier security solutions.
Top Page Image Contents