Axis Communications AXIS M3203-V user manual UPnPTM, RTP/H.264, Bonjour

Page 43

AXIS M3203-V Network Camera

System Options

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see . To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 46.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

43

Image 43

Contents Axis M3203-V Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis M3203-V Network Camera Table of ContentsRJ45 Ethernet connector with Power over Ethernet PoE Connectors and ButtonsNetwork Connector For technical specifications, seeControl Button LED IndicatorsColor Indication Set the Root Password Accessing the ProductAccess from a Browser Access from the InternetLive View Set Power Line FrequencyClick Create self-signed certificate Manual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbarPTZ Controls Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M3203-V Network Camera Basic Setup Setting Up the ProductImage VideoVideo Stream Pixel Counter264 Camera SettingsClick Save to apply the new settings Stream ProfilesImage Appearance Exposure SettingsTo configure the view area View AreaGo to Video Overlay Image OverlayOverlay Image Go to Video Video Stream and select the Image tabPrivacy Mask Using Overlay Text in an Action RuleGo to Events Action Rules Axis M3203-V Network Camera Browser Viewer Description Live View ConfigDefault Viewer for Browsers Viewer SettingsUser Defined Links Guard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControls AdvancedGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionRecommended values Default valuesMedium level 50% Low level 0%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis M3203-V Network Camera Events Recipients Setting Up an Action RuleGo to Events Action Rules and click Add Recipient Use with action Setting Up an Email RecipientGo to Events Recipients and click Add Go to Events Schedules and click Add SchedulesRecurrences To create a new scheduleGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264To add a network share MaintenanceStorage Network ShareLogs & Reports SupportSupport Overview System OverviewPlain Config Reset to Factory Default SettingsFile Upload Upgrading the Firmware TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserVideo Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalReformat the SD card and then click Mount Storage and disk management problemsStorage disruption Re-mount the storage deviceTechnical Specifications Connectors Function/group Specifications System ApplicationMaintenance Installation aids Memory PowerPerformance Considerations Function/group Specifications VideoM2.15