Axis Communications AXIS M3203-V IPv4 Address Configuration, IPv6 Address Configuration, ARP/Ping

Page 39

AXIS M3203-V Network Camera

System Options

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 46) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 39.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator)

arp -s <IP address> <serial number> ping -l 408 -t <IP address>

Windows example (this may require that you run the command prompt as an administrator)

arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125

4.Check that the network cable is connected and then restart the product by disconnecting and reconnecting power.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Axis M3203-V Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis M3203-V Network Camera Table of ContentsRJ45 Ethernet connector with Power over Ethernet PoE Connectors and ButtonsNetwork Connector For technical specifications, seeLED Indicators Control ButtonColor Indication Set the Root Password Accessing the ProductAccess from a Browser Access from the InternetSet Power Line Frequency Live ViewClick Create self-signed certificate Manual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbarPTZ Controls How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M3203-V Network Camera Basic Setup Setting Up the ProductImage VideoVideo Stream Pixel Counter264 Camera SettingsClick Save to apply the new settings Stream ProfilesImage Appearance Exposure SettingsTo configure the view area View AreaGo to Video Overlay Image OverlayOverlay Image Go to Video Video Stream and select the Image tabUsing Overlay Text in an Action Rule Privacy MaskGo to Events Action Rules Axis M3203-V Network Camera Browser Viewer Description Live View ConfigDefault Viewer for Browsers Viewer SettingsUser Defined Links Guard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControls AdvancedGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionRecommended values Default valuesMedium level 50% Low level 0%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis M3203-V Network Camera Events Setting Up an Action Rule RecipientsGo to Events Action Rules and click Add Setting Up an Email Recipient Recipient Use with actionGo to Events Recipients and click Add Go to Events Schedules and click Add SchedulesRecurrences To create a new scheduleGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264To add a network share MaintenanceStorage Network ShareLogs & Reports SupportSupport Overview System OverviewReset to Factory Default Settings Plain ConfigFile Upload Upgrading the Firmware TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserVideo Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalReformat the SD card and then click Mount Storage and disk management problemsStorage disruption Re-mount the storage deviceTechnical Specifications Connectors Function/group Specifications System ApplicationMaintenance Installation aids Memory PowerPerformance Considerations Function/group Specifications VideoM2.15
Top Page Image Contents