Panasonic WV-CW484 operating instructions Installations

Page 13

Installations

The following installation should be made by qualified service personnel or system installers.

Mounting Bracket (WV-Q114) is optional for WV-CW484F, WV-CW484FK. Use the screws provided to the Mounting Bracket.

Mounting Bracket is provided to WV-CW484S, WV-CW484SK. Use the screws provided to this product.

Important:

Prepare four fixing screws to be used to mount the provided camera attachment according to the material of the area where the attachment is to be installed.

Recommended tightening torque is as follows. M4: 1.6 N·m {1.18 lbf·ft}

Do not use wood screws to fix the camera attachment since they are not strong enough to support the weight of the camera and the bracket.

When using the provided camera attachment, make sure that either of the arrow marks faces upward.

When the installation area is not strong enough, reinforce and strenghten it or use Mounting Bracket or Ceiling Mount Bracket (WV-Q166).

Required pull-out capacity of a single screw/bolt is 196 N {44.06 lbf} or more.

When using an optional mounting bracket, refer to the operating instructions of the bracket in use.

The mounting requirements are shown as follows.

Mounting

Model

Recommended

Number of

Minimum pull-out

place

 

screw

screws

strength (per 1 pc.)

 

 

 

 

 

Ceiling/wall

(direct mounting)

M4 or equivalent

4 pcs.

196 N {44.06 lbf}

 

 

 

 

 

Ceiling/wall

WV-Q114 (approx.

*

 

470 g {1.04 lbs.})

 

 

 

 

 

 

 

 

Ceiling

WV-Q166 (approx.

*

 

680 g {1.5 lbs.})

 

 

 

 

 

 

 

 

*Make sure that the installed mount bracket can support more than 5 times of the weight of the camera.

13

Image 13
Contents Model No. WV-CW484 Series Do not Remove Cover or Back No USER-SERVICEABLE Parts Inside English Important Safety InstructionsLimitation of Liability Disclaimer of WarrantyPreface FeaturesContents Precautions Avoid installing in the following locations Observe the following for installationInstalling place Do not aim the apparatus at strong light sourcesConsumable parts Mounting screwsWhat to do if Over Heat appears on the display Major Operating Controls and Their Functions Azimuth Angle adjuster Power cable 12 V DC or 24 V AC Cautions2Optional heater connector 6 pin female 3LED indicatorLens Mounting WV-CW484FK, CW484SK Installations Using Mounting Bracket Fixing the camera attachment to the mounting bracket Using a Junction Box How to mount the cameraUsing Mounting Bracket Protrusion Screw hole of camera attachment Rear screw Camera fixing screw Waterproof processing of cable connection Waterproof ProcessWinding the provided butyl tape Downward Image Adjustment How to use a variable focal lens Zoom/focus adjustmentPrecaution Power ConnectionWire Colors & Functions Camera power cable ConnectionsCable Length and Wire Gauge Optional Heater Unit WV-CW4H InstallationIntroduction For Adjusting the Focus Before Back-focus AdjustmentFor Using General Vari-focal Lenses HintsSettings items of the camera setup About Setup MenusSetup item Description Language Basic operation Page Language Setup Language Setup Setting ProceduresCamera Identification Setting Camera ID ALC Mode with SUPER-D3 on Light Control Mode Setting ALCSuper Dynamic 3 Function SUPER-D3 ALC Mode with SUPER-D3 OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Gain Control Setting AGCWhite Balance Setting White BAL Synchronization Setting SyncAWC Setting Motion Detection Setting Motion DETManual Fine Adjustment Available time second 2, 5, 10Motion Detector Demo ModeResolution Setting Resolution Digital Noise Reduction Setting DNRBlack and White Mode Setting BW Mode About MODE2 of Motion DetectionPrivacy Zone Setting Privacy Zone Camera Picture Upside Down Positioning UPSIDE-DOWN Electronic Zoom EL-ZOOMAuto Image Stabilizer Stabilizer Lens Back-focus Setting BACK-FOCUS SetupChroma Level Setting Chroma Gain Special Menu Special SetupPedestal Level Setting Pedestal Aperture Gain Setting AP GainChroma Phase Hue Setting HUE Pixel Compensation Setting PIX OFFSerial number of the camera will be displayed To reset to the default settings Camera ResetSymptom TroubleshootingGeneral specifications SpecificationsCamera Lens WV-CW484S, WV-CW484FABF, MANUAL, AUTO/PRESET/FIX Standard AccessoriesOptional Accessories Version Française Instructions de sécurité importantes Déni de la garantie Limitation de responsabilitéCaractéristiques dominantes PréfaceTable DES Matières Cet appareil na pas dinterrupteur dalimentation Mesures de précautionPour avoir lassurance dobtenir des performances stables Ne jamais essayer de démonter cette caméra vidéoEmplacement dinstallation Éviter toute installation dans les emplace- ments suivantsPropos de lappareil déshumidificateur Vis dinstallation Principaux organes de commande et fonctions Vis de verrouillage dinclinaison Câble de sortie vidéo avec le connecteur BNCAzimut dispositif de réglage angulaire 0Vis de blocage de caméra vidéoMonture dobjectif WV-CW484FK, CW484SK Installations En utilisant la platine de fixation dinstallation InstallationsEn utilisant une boîte de jonction TOP En utilisant la platine de fixation dinstallation Comment installer la caméra vidéoUtilisation d’une boîte de raccordement Page Remarques Mise sous étanchéité du raccordement de câble Opération de mise sous étanchéitéEnroulement de la bande en butyle fournie Vers le bas Réglage de limage Comment se servir dun objectif à focale variable Réglage de zoom ou de mise au pointConnexion de sortie vidéo BranchementsRaccordement dalimentation Couleurs des fils et fonctionsDE Courant Alternatif Longueur de câble et calibre pour filsAppareil de chauffage optionnel WV-CW4H Avant dexécuter le réglage de tirage arrière ConseilsPour régler la mise au point Configuration Propos des menus de configurationAjuste le niveau de chrominance densité de la Couleur Remarque Utilisation de baseRemarques Procédures de réglage Configuration de la langueParamétrage didentification de la caméra vidéo Camera ID Mode ALC avec la fonction SUPER-D3 activée Paramétrage de mode de contrôle de lumière ALCFonction Super Dynamic 3 SUPER-D3 SUPER-D3 on Valide laRéglage de la vitesse d’obturation Shutter Mode ALC avec la fonction SUPER-D3 OFFAccroissement de la sensibilité électronique Sens UP Paramétrage de contrôle de gain AGCAjuster et le signal vidéo de sortie de Signal de sortie vidéo de la caméra vidéo àRéglage de synchronisation Sync Réglage de balance des blancs White BALParamétrage de AWC Paramétrage de la détection de mouvement Motion DETRéglage précis et manuel Détecteur de mouvement Mode de démonstrationParamétrage du mode monochromatique BW Mode Paramétrage de résolution ResolutionParamétrage de la réduction de bruit numérique DNR Propos du MODE2 de la détection de mouvementParamétrage de zone de confidentialité Privacy Zone Stabilisateur dimage automatique Stabilizer Zoom électronique EL-ZOOMParamétrage de tirage arrière BACK-FOCUS Setup 18-1. Réglage de niveau de chrominance Menu spécial Special Setup18-2. Réglage de gain douverture AP Gain 18-4. Réglage de phase de chrominance teinte HUEParamétrage de compensation de pixel PIX OFF Le numéro de série de cette caméra vidéo sera affiché Symptômes DépannageCaméra vidéo Caractéristiques techniquesObjectif WV-CW484S, WV-CW484F ENGLISH, FRENCH, GERMAN, SPANISH, Italian Accessoires standardAccessoires optionnels Panasonic Canada Inc

WV-CW484 specifications

The Panasonic WV-CW484 is a sophisticated network camera designed for versatile surveillance applications. It is a part of Panasonic's line of high-performance IP cameras that are widely used in various environments, including retail, education, transportation, and municipal surveillance. This camera stands out due to its robust features that cater to both indoor and outdoor monitoring needs.

One of the main features of the WV-CW484 is its high-resolution imaging capability. It utilizes a 1/3-inch CCD sensor that delivers clear and detailed images at resolutions up to 640 x 480 pixels. The camera supports progressive scan technology, ensuring that it captures sharp images without motion blur, which is essential for monitoring fast-moving subjects.

The WV-CW484 is equipped with a durable and weather-resistant housing, meeting the IP66 standard. This makes it suitable for installation in challenging outdoor conditions, protecting it from dust, rain, and other environmental factors. Additionally, it has a built-in heater that aids in maintaining optimal operation in low-temperature environments, ensuring reliable performance year-round.

Another notable aspect of the WV-CW484 camera is its integration of advanced digital signal processing technologies. These features enhance image quality by reducing noise and improving visibility in low-light conditions. The camera also includes a wide dynamic range function, allowing it to capture clear images in scenes with high contrast, such as brightly lit areas with shadows.

The pan-tilt functionality allows for flexible positioning and the ability to cover a broader area. Users can control the camera's movement remotely, making it easier to focus on particular areas of interest. Additionally, the WV-CW484 supports multiple streaming formats, including MPEG-4 and JPEG, enabling efficient transmission of video data across various network conditions.

For ease of installation and use, the camera is compatible with a wide range of network protocols and can be seamlessly integrated into existing surveillance systems. This versatility facilitates remote monitoring and management, allowing users to access live feeds and playback recordings from any device with internet connectivity.

In summary, the Panasonic WV-CW484 is a feature-rich network camera that combines high-performance imaging, robust housing, and advanced processing technologies. Its versatility, durability, and ease of integration make it an ideal choice for comprehensive surveillance solutions in a variety of applications.