Axis Communications 216FD/FD-V user manual Event Configuration, Event Servers, Definitions

Page 28

AXIS 216FD/FD-V - Event Configuration 28

Event Configuration

An event in the camera is when an Event Type is activated and causes certain actions to be performed. The event type is the set of parameters (or conditions) that specifies how and when which actions will be performed. A common event type is when the camera uploads images when an alarm occurs. Many event types use an Event Server, to receive uploaded images.

This section describes how to set up event servers and event types, i.e. how to configure the camera to perform certain actions when events (e.g. alarms) occur.

Definitions

Event type

A set of parameters describing how and when the camera will perform certain actions

 

 

 

Triggered Event - see page 29

The circumstances that start an event.

E.g. on a signal from an external device, such as a

 

door switch or a motion sensor.

 

 

 

 

 

Scheduled Event - see page 30

The circumstances that start an event.

E.g. at a pre-programmed time.

 

 

 

Action

What occurs when the event triggers.

E.g. the upload of images to an FTP server, e-mail

 

notification, etc.

 

 

 

 

 

Event Servers

Event Servers are used to receive e.g. uploaded image files and/or notification messages. To set up Event server connections in your camera, go to Setup > Event Configuration > Event Servers and enter the required information for the required server type.

Server type

Purpose

Information required

 

 

 

 

 

FTP Server

•

Receives uploaded images

•

Descriptive name of your choice

 

 

 

• Network address (IP address or host name)

 

 

 

• User Name and Password (for FTP server)

 

 

 

• Upload path e.g. images/

 

 

 

•

Port number

 

 

 

• Use passive mode if there is a firewall between the camera

 

 

 

 

and FTP server

 

 

 

• Use temporary file if your FTP server doesn’t allow an existing

 

 

 

 

file to be overwritten by a new file with the same name

 

 

 

 

 

HTTP Server

•

Receives notification messages

•

Descriptive name of your choice

 

•

Receives uploaded images

•

URL (IP address or host name)

 

 

 

• User Name and Password (for HTTP server)

 

 

 

• Proxy address/Proxy port (if required)

 

 

 

• Proxy User Name and Password (if required)

 

 

 

 

 

TCP Server

•

Receives notification messages

•

Descriptive name of your choice

 

 

 

• Network address (IP address or host name)

 

 

 

•

Port number

 

 

 

 

 

For details on each setting, please see the online help available from each web page.

When the setup is complete, the connection can be tested by clicking the Test button (the connection test takes approximately 10 seconds).

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Axis 216FD/FD-V Fixed Dome Network Camera User’s Manual About this Document Safety Notice Battery Replacement Contents Axis 216FD/FD-V Key features Product overviewModels DescriptionOverview LEDLED indicators LEDAccessing the Camera Access from a browserSetting the Password Accessing the camera from the InternetAdjusting the image Live View AMC audio controls How to stream MPEG-4 Video StreamsMPEG-4 clients Motion JpegAxis Media Control AMC QuickTime & Real PlayerAlternative methods of accessing the video stream Accessing the Setup tools ConfigurationAxis Media Control Video & Image settings Image AppearanceText Overlay Settings Advanced Camera SettingsVideo Stream Overlay/MaskLow Light Behavior Advanced MPEG-4 Settings GOV SettingsBit Rate Control Enable Audio Audio SettingsAudio Audio Channels Audio modeAudio Input Audio Output Live View Config LayoutUpload Own Web Files Customizing the defaultOwn Home Default Video Format Default ViewerAction Buttons Output ButtonsSequence Mode AMC SettingsHtml Examples External VideoEvent Servers Event ConfigurationDefinitions Configuring Event Types How to set up a triggered eventTriggered Event Click Add triggered on the Event typesPre-trigger and Post-trigger buffers Scheduled EventMotion Detection Port Status Object SizeSystem Options SecurityIP Address Filtering Referrals802.1x Network Admission Control HttpsAuthentication process RadiusNetwork Basic TCP/IP Settings IP Address ConfigurationDate & Time CA serversServices Network Advanced TCP/IP SettingsDNS Configuration NTP Configuration Host Name ConfigurationLink-Local Address NAT traversal port mappingRtsp QoS Settings QoS Quality of serviceNetwork Traffic Smtp email UPnPLED Settings MaintenanceBonjour Ports & DevicesConfiguration SupportUsing the Control Button Resetting to the Factory Default SettingsAdvanced Terminal connector I/O Terminal ConnectorPinout and Interface Terminal Connector Troubleshooting Setup Basic ConfigurationGo to Setup Checking the FirmwareEmergency Recovery Procedure Axis SupportCamera is accessible locally, but not externally Symptoms, Possible Causes and Remedial ActionsBrowser Power indicator is not constantly lit Camera is inaccessibleUsers Decode only I framesProblems uploading files Audio volume too low/highIs enabled under System Options Date & Time No audioTechnical Specifications IlluminationClock Software General performance considerations Optimizing your systemBandwidth Glossary of Terms Axis 216FD/FD-V Glossary of TermsAllowed to enter Half-duplex See Full-duplexVOP See VOP Megapixel See PixelAxis 216FD/FD-V Glossary of Terms SSL/TSL Secure Socket Layer/Transport Layer Security URL Uniform Resource Locator An address on the network Index AMCSnmp

216FD/FD-V specifications

Axis Communications has established itself as a leader in network video solutions, and the Axis 216FD/FD-V series is a prime example of their commitment to innovation and quality. This series of fixed dome network cameras blends advanced technology with a robust design, making it suitable for a variety of surveillance needs.

One of the standout features of the Axis 216FD/FD-V cameras is their impressive image quality. Equipped with a 1/2.8” progressive scan RGB CMOS sensor, these cameras deliver high-definition video at a resolution of up to 1080p. This ensures that every detail is captured, whether in broad daylight or in low-light conditions, thanks to the cameras' exceptional low-light performance. The ability to produce clear images in diverse lighting situations makes them ideal for installation in various environments such as retail spaces, transportation hubs, and public venues.

In addition to high-definition video, the Axis 216FD/FD-V series also offers advanced video analytics, which can help users gain deeper insights into their surveillance data. Features like motion detection and tampering alarm capabilities enhance security by alerting users to any suspicious activity. Moreover, the built-in Axis Zipstream technology reduces bandwidth and storage requirements without compromising image quality, making it an efficient choice for businesses looking to minimize costs.

The design of the Axis 216FD/FD-V cameras is another highlight. Featuring a discreet, compact dome form factor, they can be seamlessly integrated into various environments. Their vandal-resistant casing maximizes durability, ensuring reliable operation even in high-risk areas. The cameras are also IP66-rated, providing protection against dust and harsh weather conditions, an essential characteristic for outdoor surveillance.

Installation and integration are made easy with the Axis 216FD/FD-V series. The cameras support Power over Ethernet (PoE), allowing for simpler connectivity and reducing the need for additional power cabling. Additionally, they are compatible with Axis Camera Management software, facilitating efficient management and configuration.

In summary, the Axis 216FD/FD-V series offers a compelling combination of features and technologies. With its high-definition image quality, intelligent video analytics, durable design, and easy installation, this series represents a versatile solution for modern surveillance needs, reaffirming Axis Communications’ status as a pioneer in the field of network video surveillance.
Top Page Image Contents