Cisco Systems 5010, 5011 manual Service Cable, Qty Description

Page 21

Chapter 2 Installation

Service Cable

Service Cable

The dome camera includes a service port that outputs camera video. Use it at the installation site to set up the field of view and to focus the camera.

To assemble a service cable for the camera, you will need to purchase the following items from an electronics supply store:

Qty Description

1

2.5 mm stereo plug (male)

1CPM 88 miniature coaxial connector

1RG174/U coaxial cable

11/8-inch shrink fit tubing, 1/2-inch long

To assemble the cable:

Step 1 Attach the CPM 88 miniature coaxial connector to one end of the cable. Follow the directions supplied with the miniature coaxial connector.

Step 2 Attach the 2.5 mm stereo plug to the other end of the coaxial cable (refer to Figure 2-12 on page 2-10):

a.Remove the support sleeve from the plug.

b.Slip the shrink fit tubing and support sleeve over the end of the cable.

c.Prepare the cable:

d.Strip back the outer jacket 0.318 inch (8.06 mm) inch from the end of the cable.

e.Pull back the coaxial braid shield.

f.Strip back the insulating material 0.125 inch (3.18 mm) inch to expose the center conductor.

g.Solder the center connector of the cable to the center pin of the plug.

h.Pull the coaxial braid shield back through the crimp pin and solder it to the top of the crimp pin arm.

i.Crimp the end of the crimp pin around the cable.

j.Heat the shrink fit tubing around the center conductor and shoulder pin.

k.Reassemble the support sleeve and the plug.

Cisco Video Surveillance 5010/5011 Indoor Fixed HD IP Dome Camera User Guide

 

OL-22669-02

2-9

 

 

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Americas Headquarters Page N T E N T S Unicast Profile OL-22669-02 Preface Viii Models Getting StartedA P T E R Product Overview Parts ListCamera Connections and Features Top View Product Label In-Ceiling Installation InstallationPin DC AID Auto Iris Lens Positioning the Camera Surface Installation Surface Back Box Installation Positioning the Camera Installing the Dome Liner Dome Liner and Lower Dome InstallationAligning the Lower Dome with Camera Qty Description Service CableCat5 or Cat6 Cable WiringSingle Camera Wiring VAC ConnectorMultiple Camera Wiring Alarm and Relay ConnectorConnecting a Relay Device Connecting AlarmsSupervised Alarms Supervised Alarm Conditions Unsupervised Alarms19 Unsupervised Alarm Conditions Alarm ConnectionsOL-22669-02 Minimum System Requirements Camera Configuration SequenceLogging on to the Camera Accessing the IP CameraLive Video Page Icons Live VideoSelecting a Stream Primary Stream and Secondary Stream QuickView StreamUnicast Settings Taking a SnapshotDisplaying Video in the Multiscreen View General Settings Accessing the Camera MenusInformation Settings System TabCustomizing the Appearance of the Text Overlay Configuring the Time SettingsRestoring All Camera Defaults Rebooting the CameraNetwork Tab Generating a System LogGeneral Network Settings Changing the HostnameTurning On Dhcp General Imaging Settings Imaging TabTurning Off Dhcp Focus Settings Exposure SettingsTone Map Settings White Balance SettingsConfiguring the Orientation of the Scene Digital Processing Changing the Digital Processing SettingsAuto Exposure Selecting Auto Exposure SettingsDay Night Settings, Manual Exposure Selecting Manual Exposure SettingsDay Night Auto Mode Day Night SettingsDay Night Manual Mode Day Night Auto and Manual ModesConfiguring Auto Focus Settings Manual Focus Configuring Manual Focus SettingsSetting Tone Map Options Auto White Balance Selecting Auto White Balance Settings10 Manual White Balance Selecting Manual White Balance SettingsTuring Off Window Blanking Turning On Window BlankingVideo Configuration Video PresetsStreams Tab Deleting a Window Blanking Area12 Select Video Preset Configuration Selecting a Video Preset Configuration13 Custom Video Stream Configuration Configuring a Custom Video Stream ConfigurationQuality of Service for Differentiated Services Code Point Available Camera ResolutionCompression Standards Image RateProfile Rate ControlAdvance Sharpening Users and Groups TabUsers GroupsCreating a New User Includes default accounts for the following groupsDeleting a User Editing a UserCreating a New Group Editing a GroupDeleting a Group Setting the Camera to Node General Settings for Users and GroupsEvents Tab Setting the Camera to MixedSources HandlersSources Creating an Alarm Event SourceCreating a System Event Source Creating a Timer Event SourceEditing an Event Source Deleting an Event SourceCreating an Event Handler Send Email HandlersCreating an Event Handler Write Jpeg to SD Card Creating an Event Handler Open/Close Relay Creating an Event Handler Upload Jpeg to FTP ServerDeleting an Event Handler Editing an Event HandlerExample Handler Filter Setup Help MenuLog Off Menu General SpecificationsEnvironmental MechanicalPhysical VideoSpecifications OL-22669-02

5011, 5010 specifications

Cisco Systems is a leader in networking technology, providing robust solutions for businesses worldwide. Among its many offerings, the Cisco 5010 and 5011 models stand out as powerful devices designed to address the needs of modern data centers and enterprises requiring reliable and high-performance networking solutions.

The Cisco 5010 is a fixed-configuration switch that combines advanced features suitable for small to medium-sized businesses. It supports a range of Ethernet and wireless technologies, allowing seamless integration into various network infrastructures. With a capacity for Layer 2 and Layer 3 switching, the 5010 facilitates efficient data routing and switching, ensuring optimal performance for diverse applications.

On the other hand, the Cisco 5011 builds upon the 5010's capabilities, offering enhanced features and scalability. It is designed for organizations that demand higher performance and advanced networking capabilities. This model supports more VLANs and can handle increased traffic loads, making it suitable for larger enterprises or data centers.

One of the key features of both models is Cisco's advanced security protocols. They provide comprehensive protection against unauthorized access and network threats, ensuring that sensitive information remains secure. The switches also support segmentation and access control lists (ACLs), allowing administrators to manage network traffic effectively.

Both the 5010 and 5011 models are equipped with Cisco's innovative IOS software, providing users with a familiar interface for configuration and management. This software allows for automation of routine tasks, reducing administrative overhead and minimizing potential errors.

In terms of performance, both switches are built to handle high-speed connectivity, supporting multiple gigabit interfaces. They also feature advanced Quality of Service (QoS) mechanisms, which prioritize critical network traffic and maintain high performance during peak usage times. The support for Power over Ethernet (PoE) allows businesses to power devices like IP phones and access points directly through the switch, simplifying infrastructure requirements.

Scalability is another important characteristic of the Cisco 5010 and 5011. They can accommodate growth in network size and complexity without compromising performance, making them future-proof investments for enterprises.

In conclusion, the Cisco 5010 and 5011 switches are exemplary products that illustrate Cisco's commitment to delivering high-quality networking solutions. With their advanced features, robust security, scalability, and high performance, they cater to the needs of modern businesses looking to enhance their connectivity and operational efficiency.
Top Page Image Contents