Samsung SCC-C6455N user manual Night

Page 23

CAMERA SETUP MENU		STANDARD	ITS	BACKLIGHT	DAY/NIGHT	GAMING
		STANDARD	ITS	BACKLIGHT	DAY/NIGHT	GAMING
Parent Menu	Sub-menus

MOTION		(F.FAST)	(F.FAST)	NORM	(F.FAST)	SLOW
MOTION		---	---	NORM	---	SLOW
		---	---		---

DNR		MEDIUM	MEDIUM	MEDIUM	MEDIUM	MEDIUM

SHUTTER		OFF	OFF	OFF	OFF	OFF

SENSE UP		AUTO X4	AUTO X2	AUTO X4	AUTO X4	AUTO X4

XDR		MEDIUM	MEDIUM	MEDIUM	MEDIUM	MEDIUM

		AUTO	AUTO	DAY	AUTO	DAY

	NIGHT	-	-	-	-	-

DAY/NIGHT	BURST	OFF	ON	OFF	OFF	OFF

	EXT	-	-	-	-	-

	BURST	OFF	ON	OFF	OFF	OFF

		DAY	DAY/NIGHT	DAY	DAY/NIGHT	DAY

	DAY	-	-	-	-	-

	MODE	ATW2	ATW1	ATW1	ATW1	ATW1

	RED	0	0	0	0	0

	BLUE	0	0	0	0	0
WHITE BAL
WHITE BAL	NIGHT	-	-	-	-	-

	BRIGHTNESS	Custom Setting	MEDIUM	Custom Setting	MEDIUM	Custom Setting

	MODE	OFF	ATW2	OFF	ATW2	OFF

	RED	Custom Setting	0	Custom Setting	0	Custom Setting

	BLUE	Custom Setting	0	Custom Setting	0	Custom Setting

DETAIL		2	2	2	2	2

English

English _23

00885A-NA_SCC-C6455N-ENG.indb 23

2009-08-05 오후 2:43:

Image 23

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesFrame SET At a GlanceCamera Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Use SW606, SW605, and SW604 to specify the camera address Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationVideo terminal on the rear of monitor BNC Cable Connecting with Other deviceConnecting to a monitor To connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu  ITS ProfileNight VPS You can configure the general settings of the camera moduleCamera SET Camera IDBLC With Backlight set to IrisDNR With this, you can adjust the AGC level of aAGC MotionXDR ShutterSENS-UP FlickerlessAny excessively bright area in a night scene will be MASKed You can specify a recording mode according to the sceneDAY/NIGHT SET-AUTO SET are not available Auto Switch or Auto FocusWhite BAL  You can specify Mask 1 and 2 simultaneouslyDAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset SET. pages 24 ~ Select the preset numberSelect Position and adjust PAN You can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup ~ 511 for Preset Auto Play SetupSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Tilt range -6˚~186˚ Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Manual Pan Speed 0.01˚~ 180˚/secProduct Appearance 00885A-NASCC-C6455N-ENG.indb 2009-08-05 오후